Common Holley Carb Leak Solutions | Holley Carburetor Tuning Secrets |
HTML-код
- Опубликовано: 30 янв 2022
- Today we are looking at all the different problems and solutions when it comes to holley carbs and their common leaks. The holley carburetor is known for its constant leaks but in this video I will not only show you the causes of the leaks but also the solutions and how to fix them. Videos like these are a part of showing people how easy it actually is to work on your own carburetor. This video is part of the holley carb secrets tuning video series so if there are other questions, feel free to check out those videos first and if I havnt gotten around to making a video on your question, feel free to reach out to me in the comments below.
#Holley #HolleyCarbTuning #HolleyCarburetor 
Авто/Мото
![Natanael Cano x Oscar Maydon - Giza [Official Video]](http://i.ytimg.com/vi/eXCS6-MSQ_Y/mqdefault.jpg)
Perfect video. Just what I was looking for. Gets right to the point without a lot of fluff and jibber jabber. Well done.
Thanks man, more carb tuning videos coming out soon 👍
Just want to say thank you. Your video helped me diagnose my leak on my '70 Z28. Have a terrific day
From teaching me how to properly use my flex core to fixing my carb leak 🤙🏽🍻 wanted to say again, thank you !
Glad I could be of assistance 👍
I fixed my 780 problems. After having an off idle stumble besides a surge at cruise at any speed and an idle that would not go down, I tore my 780 apart. I found wet gaskets and areas that should not be wet and a blown prim power valve.
I ended up filing warped parts especially the body bottom, the bottom throttle plate side and a bit on both body surfaces where the metering block meets. I spent a total of 5 hrs filing. It works great now after replacing gaskets, power valves and so on.😅
You're a good teacher and very knowledgeable. Many thanks for your videos.
Thank you sir! I really appreciate it!
Great information!
This is a really really good video!
What a great video. Explains the topic really well Thankyou
Thank you! I hope it helps!
Such a great informing video
One of the greater explanations And visual breakdownI have seen On RUclips
Hey man, thank you! I hadnt seen your comment but I appreciate it!
All of this information is great! Thank you!
I appreciate it! Hope it helps!
Wow ...thank you so much for sharing ...learnt a lot from this video
Thanks man. I hope it helps!
Thanks this helped alot
Outstanding video!!!!!
Thank you sir, I appreciate it 👍
Hey I just found your videos, I’ve learned so much! Thank you. I’m having trouble with my Holley pouring fuel from the vent tube in my primary side. At high idle and driving it runs fine but when I let off the throttle it starts pouring fuel from my vent tube on the primary. I’ve checked the needle and seat, replaced the O ring and adjusted.
Hey man, what is your fuel pressure?
Great videos
Thanks man, good to see you 👍
Best video on these Holley leaks. I have original 735 cfm for my 68.5 CJ. No one’s been able to diagnose the source of leak which is on the upper right where body meets bowl and it sounds to me like he might be the accelerator?
Just fixed my leaky vent after a few years. Thx
Really good video!! Easily can tell you know your stuff
I really appreciate it Billy!
Mine was leaking at the same place caught fire. 🔥
Lots of great info! Its been 10 years since i had to play with one. But got this old holley 4 barrel on a project car. Was just rebuilt prior to buying the car from a reputable carb shop. 2 months later and maybe 1k miles of driving I have a decent size fuel leak from throttle shaft area. Other than shaft being worn, can anything else cause it like over-filled bowls?
Thanks again
If the shafts are leaking, the shaft bores are worn out. Somtimes they have nylon seals and other times its just metal to metal from the factory. You might also develop a vacuum leak from there. They sell bushing repair kits but I would recommend replacing the base plate. Good luck 👍
Hey man just found your videos a while ago and I've been watching all your welding ones. can you do a video on how to weld tool steel for repairing like a broken wrench, Hammer, Etc...? Ive checked around youtube and cant gind any videos on it
Hey man, I Havnt done too much tool steel welding but I have done it a few times. I've found that it takes less travel speed, More heat and less wire speed to get the metal molten enough for you to be able to get a solid weld in. Also beveling the two pieces before you weld them together helps a lot too.
@@NightWrencher thanks! I'll try all those things. I have a rare hammer that my dad gave me. It has alot of sentimental value and the claw broke off.
I bought some vasaline and chapstik to put on gaskets for my next carb rebuild. I'm hoping it helps, especially on the paper gaskets. What do you think? Or maybe antisieze or motor oil or trans fluid on the gaskets and the O ring on the needle and seat.
Ive heard that chapstick works pretty well but I've never tried it myself. Vaseline on the orings might work too. I usually install the gaskets bare and use motor oil or PBblaster as a lubricant to install the orings.
I have a holley carburetor with a float bowl on the front and rear of the carb. There is a straight steel fuel line that connects the two bowls. Fuel is leaking out of both ends of that steel line. It is almost as if the line needs to be longer. What should i do?
I have a brand new 600 Holley Brawler with mechanical secondaries and after making changes to tune it for my 306 I’ve noticed the secondary fuel bowl leaks down after filling it. There’s no power valve in it because it came with a plug, I have no visible leaks outside of the carburetor and I’m really stumped on this one, any advice would be greatly appreciated!!!
Well, fuel has to go somewhere and if its not leaking outside, its probably leaking into the engine. Where exactly, I dont know but if you can pinpoint if the fuel is leaking through the idle holes, accel pump, boosters, tslot or air bleeds, you'll be able yo find the cause really quick.
Does the casing that holds the accelerator pump ever get warped and no seal correctly? I noticed a fuel around the sides of the accelerator pump so I replaced the actual accelerator pump gasket because I thought it was ripped or something. It looked fine but I replaced it anyway. When I started up the car again I could still see the fuel seeping out the sides. So I was wondering if the casing maybe is warped and not sealing all
The way. Thanks in advance!
Sometimes it does happen. Running it over a piece of sand paper and check the pattern. Usually its just a little warped but it shouldnt be too hard to fix
@NightWrencher Do you happen to have any idea why my secondary squirter drips fuel slowly when the car is off? Ive tried everything i can think of and nothing works. I appreciate any insight you can give. Ive searched high & low online with no answers.
Make sure you have a steel needle inside the squirter fuel feed and make sure its clean. When the car is off, fuel expands and sometimes escapes through the squirters. Once the engine cools off or leaks enough gas, it will stop leaking. Not really a dangerous problem unless its flooding the engine or leaking to the outside of the carb.
@@NightWrencher you helped me narrow it down. The brass seat under the steel needle had a defectin it. Used a small punch and hammer on top of the needle and it reformed the brass seat. Good to go! Thanks brorher!!
@@jeremiahfiek5495 thats awesome, great job!
Hey senor Nighwrencher,
Not sure if it is me or my carb. I have a 750 4150 Holley on a 396 BB , my El Camino is insane Up to say 100 ish mph, and just seems to take its sweet time getting up to the HP at 4500 - 5600 RPM, my cam, heads, intake are all matched up at 1900-5800 rpm Edelbrock and Comp cam, I have a AF gauge, it seems to be fine all through the entire rpm range, just seems to take its time at the top end , the build is supposed to be a 550 ish build, any thoughts? I am concerned about the carb CFM but it should be fine 🤔🤔🤔🧐😵💫
It sounds like your set up is dialed in but keep in mind that max horsepower does not dictate how the engine accelerates. If you've ever been on a dyno, you can see where the power starts to flatten out before it drops off, that's probably what you're feeling. Without completely changing your engine, I would suggest switch out to a shorter gear ratio
@@NightWrencher Well the gearing is a 700R 4 built with a 22-2500 stall, locking Tq and posi w 342 gears , first into second is all about burning rubber she is mean from shit to get, I just would like to see it act the same all the way through the gears.
I guess Dyno is my best shot 💉 now, and I really love your shows I have used them to go ahead with my AF gauge system, I was only off on my primary jets from 72s to 65s after the install , not to shabby from being a plug reader from the early 1970s. 🤔😉 Peace
👍💪
👊
What causes a dead peddle on a holly 4160
What do you mean when you say "dead pedal"
I don't have a fuel return, so fuel pressure goes up after I turn it off. The bowl levels start to go up, and just enough fuel blocks the air bleeds and then it develops a very slow leak on the butterflies
more than likely thats caused by heat soak. Try using a wooden or plastic half inch spacer
@@NightWrencher thanks, I'm putting in a return regulator and love to the tank. I just don't see a way around it at this point. I don't fuel in my new engine oil
Thats the best way to take care of it 👍
If you're having a connection Weak use the Indian Head and make sure those washers have no Burz. on them. Use the artist brush put some indian head on the threads and the washers
Don't forget to not use a electric tool. My 800 carb became a paperweight
It depends on what tool you use. I use an electric drill with an adjustible clutch. I snug them down close and tighten them by hand