If you flip the calipers so you can see the screen when measuring. you'll take better measurements because you can see where and when it's registering best. I've never - ever succeeded at using them the way you do. They always move just a little when I remove them from the work. Aluminum cuts so unbelievably well with HSS tooling; way nicer than with carbide. You can get such a keen edge with HSS. Use kerosene for cutting aluminum.
@@ypaulbrown WD40 is mostly ICP solvent. This is a proprietary product that is very much like de-oderized Kerosene (it may be kero with a special treatment). There's a touch of hydrotreated light pump oil, engine oil and light and heavy hydrotreated paraffins in it. Years ago the MSDS listed the CAS # for aviation jet fuel as almost 100% with a wee skosh of mineral oil. Kero is why it's good on aluminum. You can just buy kero it's so much cheaper.
Leaving a chuck key (ratchet with extension) in the chuck is one of those things that turns out badly someday. I think it would have been nice to see proper measurements taken to avoid the time consuming process of, measure, hog some more out, measure again, rinse and repeat. Instead, just measure, and know each turn on the cross slide will enlarge the hole by 0.020"
For your own safety you should take your ring off while you're doing machining...... And it would be best if you would roll your sleeves up too (rather than risk them getting caught in the machinery). BTW..... Where are the "turning tricks" that we were supposed to see? From what I can tell you got quite a bit of chatter on your external threads.
I agree with you 100%, no commentary whatsoever so how is any of this tips. I’m completely new to running a lathe and just bought my first and I’m already seeing mistakes in this video so I’m not sure how any of this would be tips, don’t teach bad tips, proper measuring, documenting etc.
I’ve been eyeing that Chinese QCTP, haven’t pulled the trigger just yet. Just a free suggestion, grab a set of cheap snap-spring ID feelers. I think I paid $50 for a set of 7 that ranges from 1/2” to 5”. It’s way more accurate and easy to use. Keep up the great work
No tricks,, just foolish long sleeves and foolish wedding rings,,a trick would be how to untangle your shirt sleeves and get ring off after the lathe got done with them.
I know this was posted 4 years ago but is there any way you could let me know more about your lathe mainly tool holders and quick change part number pls
Good night, I'm from Brazil and I really liked your RUclips channel, I have a lathe similar to yours and I would like to know if your lathe has slack, hug.
I enjoy watching your videos. When you were cutting the inside thread, I noticed that you adjusted the compound each time you turned the cross slide. Why was this?
hello Ive see that you use the tread handle and not the clutch ? have you a problem with him, Iv an old sheldon 1936 model and it is an similar lathe and mine lathe have this clutch ,I has a problem with the piñon that go engange with the leadscrew but ive replace this piñon because he dont engaeged , now he go good nice video bye
I like the long sleeves...
That and long hair or sweater string have hurt many young high school and college student in shop class.
If you flip the calipers so you can see the screen when measuring. you'll take better measurements because you can see where and when it's registering best. I've never - ever succeeded at using them the way you do. They always move just a little when I remove them from the work.
Aluminum cuts so unbelievably well with HSS tooling; way nicer than with carbide. You can get such a keen edge with HSS. Use kerosene for cutting aluminum.
WD-40 also works great on aluminum for cutting
@@ypaulbrown WD40 is mostly ICP solvent. This is a proprietary product that is very much like de-oderized Kerosene (it may be kero with a special treatment). There's a touch of hydrotreated light pump oil, engine oil and light and heavy hydrotreated paraffins in it. Years ago the MSDS listed the CAS # for aviation jet fuel as almost 100% with a wee skosh of mineral oil. Kero is why it's good on aluminum. You can just buy kero it's so much cheaper.
Leaving a chuck key (ratchet with extension) in the chuck is one of those things that turns out badly someday. I think it would have been nice to see proper measurements taken to avoid the time consuming process of, measure, hog some more out, measure again, rinse and repeat. Instead, just measure, and know each turn on the cross slide will enlarge the hole by 0.020"
For your own safety you should take your ring off while you're doing machining...... And it would be best if you would roll your sleeves up too (rather than risk them getting caught in the machinery).
BTW..... Where are the "turning tricks" that we were supposed to see? From what I can tell you got quite a bit of chatter on your external threads.
I agree with you 100%, no commentary whatsoever so how is any of this tips. I’m completely new to running a lathe and just bought my first and I’m already seeing mistakes in this video so I’m not sure how any of this would be tips, don’t teach bad tips, proper measuring, documenting etc.
You promised "tricks"! Sadly, I stayed till the end! .....Where?
Wakodahatchee Chris
que bonita maquina aprendi en mi colegio con un torno South Bend .. gran video
Why is everyone using carbide inserts? Even Mr. Pete is using them. I thought HSS was the ticket for small lathes like this one. Just wondering.
I’ve been eyeing that Chinese QCTP, haven’t pulled the trigger just yet. Just a free suggestion, grab a set of cheap snap-spring ID feelers. I think I paid $50 for a set of 7 that ranges from 1/2” to 5”. It’s way more accurate and easy to use. Keep up the great work
Thought we was going to see some tricks,,,not simple turns
Good work 👍
Real question is, is that 29°angle or 30°¿
No tricks,, just foolish long sleeves and foolish wedding rings,,a trick would be how to untangle your shirt sleeves and get ring off after the lathe got done with them.
You seem to enjoy lathe work, if everything is good make some more videos. There is always something to share
maybe im tripping but your chuck doesnt seem to run 100% true, looks like its trowing a bit maybe its just the video
I know this was posted 4 years ago but is there any way you could let me know more about your lathe mainly tool holders and quick change part number pls
Good night, I'm from Brazil and I really liked your RUclips channel, I have a lathe similar to yours and I would like to know if your lathe has slack, hug.
Not bad man keep going you’ll get there invest in some nice mics tho
I enjoy watching your videos. When you were cutting the inside thread, I noticed that you adjusted the compound each time you turned the cross slide. Why was this?
he likely was returning the cross slide to the same spot every time and advancing the compound in each time to take the deeper bite
@ 7:17 is a no no no no tools over there no no no no
I think we have been tricked!
hello Ive see that you use the tread handle and not the clutch ? have you a problem with him, Iv an old sheldon 1936 model and it is an similar lathe and mine lathe have this clutch ,I has a problem with the piñon that go engange with the leadscrew but ive replace this piñon because he dont engaeged , now he go good nice video bye
Hi, always use the lead screw engagement when threading and the clutch when taking regular cuts. Hope you can get it figured out. Thanks for watching
You got this thing called a power feed. Try it sometime
cat got your tongue?
Why not measure?
and the 'tricks?'
I give up! 10 min in and no trick.
Long sleeve shirt, not tucked in. smh
I guess I don't get it... What trick ??? This is a normal common job for a lathe ! What trick ?
Steve Lamperta hi Steve, it was just a play on words when thinking of a catchy title. Thanks for watching
nice try
He Made the Part. good job. Now some Safety lessons.