BTW your engine temps were good, you could approach temps of 230ish safety, and you were under 200 when you checked. After a couple tanks these engines run better, I'm sure you know. Anyway, the NItroGang is here to support you!>
Hey Maddi, the break-ins are sometimes rough, even for new RCs. You did what you could. I ran into this same issue over the weekend with a brand new T-maxx Break in. Turns out the Low Speed Needle needed to be richened like 1 whole turn and the Idle set-screw needed to be turned in (raised). Then it ideas well.
Hobao have some great nitros as this one!!Thanks for sharing with us this video! A little note: Turbo Glowplugs as you showed one ,only fits on engines with the turbo chamber,they have a different coil size:-) The best plugs that you can use on this Hobao engine are following plugs: -O.S. engines A5 -LRP R5 -RB Concept 6 (sadly this manufactor had closed the business ) Nice regards V-1
Nice you got it never give up! It was the fuel for some reason it didn't want to prime cause seems some issues with the ball end side slipping that was def the issue! 🙏
I would also remove that engine if still have problems go over the clutch make sure everything tight and also make sure that starter is not have any internal issues!
based on the info on this video. i am going to say it's running too lean, on the high and low speed needle, of the carb. based on the hard to start, stay running and high rev sound, after blip of throttle... not sure if you said it was new or not. but if not, the carb might need disassembling. cleaning the sticky oil off the needles might be needed..... i am going to say i was part right based on my last comment.... great video i liked it
Good video at certain times I felt like you was getting Frustrated and going to give up but you didn’t you stayed in it to win it lol good job #nitro4live👍💪
Hi I like the hyper cage hope you dont mind Me asking I am think about getting the same steering controller as you how do you find it any problems etc thanks
I wanna get one of these the cage on that buggy looks cool maybe i will get one of these one day but buying new rcs is becoming addicting and im terrible at managing money maybe after 6 months of saving if they still available by then because losi and associated have cleared all there nitros out for rtrs they still do kits but its really sad to see that there is not much choice i hope more people get into nitro i wish i never touched brushless in the first place
BTW your engine temps were good, you could approach temps of 230ish safety, and you were under 200 when you checked. After a couple tanks these engines run better, I'm sure you know. Anyway, the NItroGang is here to support you!>
Hey Maddi, the break-ins are sometimes rough, even for new RCs. You did what you could. I ran into this same issue over the weekend with a brand new T-maxx Break in. Turns out the Low Speed Needle needed to be richened like 1 whole turn and the Idle set-screw needed to be turned in (raised). Then it ideas well.
Glow plugs rule of thumb hot weather cold plug. Cold weather hot plug
Hobao have some great nitros as this one!!Thanks for sharing with us this video!
A little note: Turbo Glowplugs as you showed one ,only fits on engines with the turbo chamber,they have a different coil size:-)
The best plugs that you can use on this Hobao engine are following plugs:
-O.S. engines A5
-LRP R5
-RB Concept 6 (sadly this manufactor had closed the business )
Nice regards V-1
@@MaddiNitro Welcome my nitro Sis,always happy to help!
As you like Nitro on-roads you should take a look at my newest upload ;-)
Dope Maddi, you go girl! This journey was/is a great way to make nitro great again! 😈👍💯😎
Nice you got it never give up! It was the fuel for some reason it didn't want to prime cause seems some issues with the ball end side slipping that was def the issue! 🙏
Just got work on the tune now richen the high
I would also remove that engine if still have problems go over the clutch make sure everything tight and also make sure that starter is not have any internal issues!
I'm might getting the hobao monster truck soon I've have had couple of hyper 7 buggy great rc nitros
I always loosen glow plug on big block motor starts easier less strain on rod when it starts tighten glow plug
based on the info on this video. i am going to say it's running too lean, on the high and low speed needle, of the carb. based on the hard to start, stay running and high rev sound, after blip of throttle... not sure if you said it was new or not. but if not, the carb might need disassembling. cleaning the sticky oil off the needles might be needed..... i am going to say i was part right based on my last comment.... great video i liked it
Good video at certain times I felt like you was getting Frustrated and going to give up but you didn’t you stayed in it to win it lol good job #nitro4live👍💪
Great job glad you got it started
That’s a really nice cage
Hi I like the hyper cage hope you dont mind Me asking I am think about getting the same steering controller as you how do you find it any problems etc thanks
I wanna get one of these the cage on that buggy looks cool maybe i will get one of these one day but buying new rcs is becoming addicting and im terrible at managing money maybe after 6 months of saving if they still available by then because losi and associated have cleared all there nitros out for rtrs they still do kits but its really sad to see that there is not much choice i hope more people get into nitro i wish i never touched brushless in the first place
You can order the roll cage from HoBao. Unfortunately, I does not come as a complete kit. You have to order it in parts.
Sweet video 👍🔥🔥🔥🔥
Hey! Haha you got it running yay! Get a jammin jp-1pipe