A200 Hobart Service

Поделиться
HTML-код
  • Опубликовано: 5 янв 2025

Комментарии • 135

  • @johnnieholt1188
    @johnnieholt1188 9 лет назад +33

    A couple of hints that might help someone tearing down their A200.
    1. If you reassemble the mixer, and you hear a clunk every revolution of the planetary on speeds 2 and 3, loosen up the nut on the top of the main drive shaft outside the top cover. You should only tighten this nut until it just barely seats. Maybe even a bit looser. Wrenching it down will cause the clunking noise. It's a lock nut, so you don't have to tighten this down to keep it from coming off.
    You'll also get the clunk if you grease the planetary. It might take a minute or two for the clunk to go away once the grease spreads out. Once it's good, you shouldn't hear any noise. The mixer should run completely smooth.
    2. I used a synthetic, automotive grease - NLGI #2 for the transmission. I bought this at my local auto parts store. This suggestion came from a restaurant service tech who works on these mixers. He advised staying away from red grease, and going with green or black. In his experience, the red breaks down, and leaks too quickly. This grease does not have to be food grade for proper functioning, although health laws might require it. I use my mixer at home, so health laws don't apply. The price difference between food grade grease (especially the Hobart part), and the automotive stuff was significant.
    For the planetary, you do have to use food grade grease. Again, NLGI #2. I used MobilGrease FM221. I bought it off of Ebay, as finding it locally was difficult. $20 for a 14 ounce tube.
    Tearing the transmission apart, as well as the planetary, and cleaning / greasing everything was a smart thing to do. Considering the cost of Hobart parts, and the number of gears, bearings and worm drives, regular maintenance makes tons of sense.
    3. When you're using the screw to remove the top, inner cover to expose the transmission, it will lift the cover from the front first. Gently help the back to lift as well as you tighten the screw down. Allowing the front to come up first will cause the cover to lift out all of the shafts and gears, making it very difficult to see how it all goes together.
    4. If the clutch comes apart in pieces, the springs adjacent to the rollers go on the side of the clutch assembly. The hollow side goes toward the housing, and the bulging out side goes toward the rollers. There's one spring for every roller, and it's easy for these springs to fall into the grease and disappear.
    Finally, take detailed pictures as you're removing things. The Hobart tech literature is not great, and it's hard to see how things go back together if you don't have pictures. Also, getting info out of Hobart is almost impossible. If you need a service tech, Hobart will not come to a home-based business. Try calling your local restaurant supply place, and get the name of an independent technician. Expect to pay for travel time, and two calls. One to tear down and diagnose, and the second to return after the tech gets the part. Most independent techs have a limited supply of parts.
    Again, thanks for this video.

    • @Yosh-doesnt-understand
      @Yosh-doesnt-understand 7 лет назад

      Johnnie Holt I just replaced the main key in the gear box and I am getting a clicking sound in low gear. But the higher gears run smooth. Any thoughts to what might cause this?

    • @deansheridan
      @deansheridan 5 лет назад

      Johnnie Holt any suggestions on pulling the key out of the drive ? I seem to be reshaping the edges with my needle nose pliers

    • @mkhan-ny6nq
      @mkhan-ny6nq 4 года назад

      Hi Johnnie quick question Bush that fits on bottom end of main shaft what's its purpose and if not installed will it cause a problem?

    • @mkhan-ny6nq
      @mkhan-ny6nq 4 года назад

      A200 I have speed 2 and 3 but have lost speed 1 it spins but you can stop the shaft by hand any idea what the problem is?

    • @intheclutch4618
      @intheclutch4618 3 года назад

      Hey

  • @markhull9156
    @markhull9156 3 года назад +7

    I'm very impressed. I thought this was a particularly clear and well-done exposition of what a person needs to know if they should choose to dive into one of these. (Just remember his opening comment about this machine being prepped for the video.)

  • @emmettkelly7465
    @emmettkelly7465 9 лет назад +6

    Thank you. Thank you. Thank you. This video was beyond valuable in rebuilding my A200. Getting info out of Hobart is a nightmare.
    You are a God.

    • @franknavarrette1015
      @franknavarrette1015 6 лет назад

      Emmett Kelly
      Hi I have a HOBART mixer D300 20qts.spinning to slow and if I hold the shaft she will stop can you held finding what the problem maybe

    • @charlesburow8120
      @charlesburow8120 5 лет назад

      Frank Navarrette it sounds like you have a broken key in the transmission. The key usually breaks in half lengthwise. There is enough of a bite for the mixer to turn till you put it under a load. If you find a broken key you should change the grease and it would be a wise idea to change the shifter bushings. The bushings can wear causing a loss of speed.

  • @mrcarlopiazza1
    @mrcarlopiazza1 4 года назад +1

    my a200 mixer does not knead my dough...its weak.
    however it spins when there is no load
    when i press on button i hear a humming but the dough arm is too weak

  • @baoqdang-ll2fx
    @baoqdang-ll2fx 5 месяцев назад +1

    How do you remove old grease

  • @JC-Jason-DK
    @JC-Jason-DK Год назад

    Are the top bearings for the worm and transmission gears upside down? I have seen them different on my videos thank you.

  • @jeffreyoyibo2475
    @jeffreyoyibo2475 Год назад

    What do I do when the transmission gear stop rotating after some motion

  • @mikeharvey9811
    @mikeharvey9811 3 года назад

    Excellent , Chrystal clear, Thank you so much. Mike

  • @ahmednasef1991
    @ahmednasef1991 3 года назад

    Where to find the handle, mine is broken!

  • @denissequera5569
    @denissequera5569 3 года назад

    Excelente vídeo. Alguien me puede orientar con el link que tenga la traducción de este vídeo. Gracias.

  • @ogsixto
    @ogsixto 11 лет назад

    Thank you very much for posting this video you just save me a lot of money

  • @rockgee
    @rockgee 9 лет назад +6

    I wish I could find the same type of video for a Hobart D 300 mixer.Does anyone know of one?
    Rock

    • @charlesburow8120
      @charlesburow8120 5 лет назад +1

      rockgee it’s basically the same steps just on a bigger scale and more grease. A suggestion is to replace the shifter bushings before you reassemble the transmission. The bushings are brass and they can wear. If they wear then you could loose a speed. Good luck

  • @LuisAlejandroRodriguezSusarret
    @LuisAlejandroRodriguezSusarret Месяц назад

    Cómo podría adquirir el Embobinado o Camisa de Hobart A_200... Si, podrían darme mayor información de lo agradecería mucho... Gracias.

  • @johnaltopiedi6746
    @johnaltopiedi6746 3 года назад

    Hello I have a question, and I think you can help, I have a Hobart A-120T it looks very similar to the A200 I want to remove the Gear change to lubricate the shaft .Can I take that out without removing any inner parts . and be able to slide the shaft back in .Thank You so much. John

  • @GuestU2
    @GuestU2 3 года назад +1

    Great video. I'm looking for a Hobart D-300 video to replace grease, or oil. A service video if anyone knows of one. Thanks

    • @jeremypointer3392
      @jeremypointer3392 Год назад

      Did you find a video for the D-300? I could use a tutorial on that machine too!

  • @dinocalderon9504
    @dinocalderon9504 9 лет назад +1

    TENGO UN MIXER A200 DE 20QUARTS Y LE HABRI LA TRANSMISSION. POR QUE SONABA ALGO ADENTRO Y YA NO AGARRAVA LAS VELOCIDADES LA PRIMERA Y TERCERA Y SOLO ENCONTRE UNA ARGOLLA DE ACERO CON UNA ABERTURA Y NO SE SI ES ASI ABIERTA O SE ABRIO IVA EN EL ENGRANE QUE VIENE DEL MOTOR

  • @elmar7900
    @elmar7900 4 месяца назад

    A mi maquina se le quebro la cuña de sincronisacion de cbios no se como es!! Salio en pedasos pero como recontruirla!!! ??????

  • @PizzaManNick
    @PizzaManNick 2 года назад

    Thank you so much for this great information!

  • @chefbrucer
    @chefbrucer 6 лет назад

    Hola, I wonder if you have a video, how to change the oil or add oil.
    Thanks

  • @airplayespressobakery6452
    @airplayespressobakery6452 6 лет назад

    I cant seem to see where to place the A200 driving key on the shaft. It fell out when removing the shaft. The item is M13024.

    • @charlesburow8120
      @charlesburow8120 5 лет назад

      Airplay Espresso and Bakery the Divin key? If that’s it the location is on the center shaft. The gear that rests in the shifting yolk is where it goes. You will see a spring loaded bar on the center shaft. The gear (has a hole in it ) ,and the divin key has a small nipple on it which rests in that hole. You need to put the pieces together while on the shaft pushing against the springy bar and pushing down at the same time. It’s a pain in the butt. If someone could show you that would make it way easier.

  • @leomardua2367
    @leomardua2367 2 года назад

    Gracias por enseñarme como se hace el mantenimiento mecánico de la batidora Hobart

  • @367Richard
    @367Richard 6 лет назад

    Hello can i ask a question I have an AE200 and have just replace the carbon and replace it all but now no 3rd gear can you give me some idea what wrong ? kind regards Richard

  • @sereyoudomchum9979
    @sereyoudomchum9979 3 года назад

    Really well explained. Thank you so much sir

  • @LSMH528Hz
    @LSMH528Hz 4 года назад

    Hello, I'm trying to fix a A200 that leaks oily grease to the planetary after it's been unused for decades. I noticed the spacer the oilseal seals on has a neat groove around it just about where the seal should be. Is this wear or does it belong there ? And does anyone know where i can buy parts in west europe ? Many thanks !

    • @Longwood75
      @Longwood75 4 года назад

      That groove is from wear. The spacer should not have a groove around it.

  • @cumbiachamacos
    @cumbiachamacos 7 лет назад

    Que tal saludos. En una hobart h 600 el balero que ba en el planetario se nete de abajo para arriba o hay que mover la transmicion y meterlo pir arriva? .. grasias. .

  • @boromsun8863
    @boromsun8863 6 лет назад

    Hello, do you know how to open the gear box cover for Uniworld 30qt mixer? I'm having a hard time trying to open it. Thanks!

  • @kennykeating5243
    @kennykeating5243 6 лет назад

    The one I'm trying to fix at work isn't going into second speed when it's mixing dough. But it will without resistance. Why might that be and how should I fix it? Thanks for your thoughts.

    • @owenwhitman6616
      @owenwhitman6616 6 лет назад +1

      Just had this one... The worm gear follower (The brass gear that meshes with the worm gear on the motor) was stripped. Has enough grab to run without load, but once loaded it slipped.

    • @charlesburow8120
      @charlesburow8120 5 лет назад

      It could also be a broken key. One of the keys will break lengthwise. Usually this happens if someone shifts the mixer while it’s under a load and running.

  • @veronicar4989
    @veronicar4989 7 лет назад

    Hi, could you show how to do this for a Hobart n50?

  • @oscarhernandez3100
    @oscarhernandez3100 2 года назад

    What if it doesn't shift to 3rd gear?

  • @chadelliott8012
    @chadelliott8012 8 лет назад +1

    Can I replace the switch with a "dimmer light switch" to allow slow starts when mixing?

    • @RobbSadler
      @RobbSadler 6 лет назад +1

      No, you would do damage to the motor.

  • @jesussilva7706
    @jesussilva7706 6 лет назад

    I have an old model A200, with light switch for on/off. That I had replaced grease, now unit has ware gears 1, and 2 are binding. What should I check?

    • @charlesburow8120
      @charlesburow8120 5 лет назад

      Jesus Silva look for any burrs on the gears. If you changed the grease but didn’t completely remove all of it there can be small metal shavings in the old grease. That old grease can migrate in between the gears and bind them

  • @GaudencioTrejo
    @GaudencioTrejo Месяц назад

    Disculpe la mi le movi y no trabaja la primera en 3 y primera trabaja rrecio me puede ayudar

  • @DiegoRamirez-jr8li
    @DiegoRamirez-jr8li 3 года назад

    Muchas gracias muy bien esplicado bendiciones desde colombia

  • @noonakane
    @noonakane 7 лет назад

    Thank you for the video. Really hope me in this moment.

  • @melburnewalker659
    @melburnewalker659 4 года назад

    Need to have a diagram of the low speed gear

  • @mkhan-ny6nq
    @mkhan-ny6nq 4 года назад

    Hi, gear 2 and 3 runs fine gear 1 spins but can be stop by hand what could be the problem ?

  • @sliceofitaleighpizzacheese8761
    @sliceofitaleighpizzacheese8761 6 лет назад +1

    This example has no gear oil at all. Mine is FULL of gear oil. Is this normal? Also I think I put the gears on wrong, but they fit perfectly, and it only has 2 speeds, REALLY REALLY slow and then fast....wtf??

    • @jscarnucci2636
      @jscarnucci2636 6 лет назад +1

      why not show how to apply grease?!?!

    • @charlesburow8120
      @charlesburow8120 5 лет назад

      Yes the transmission will be full of grease. You need to remove all of it before you make a repair. There are wearing brass parts that can leave small shavings in the grease. Check all the keys, and replace both shifter bushings. The bushings are brass which wears and can cause a loss of a speed.

  • @curtisneedham6083
    @curtisneedham6083 11 лет назад

    I would like to ask about the setting of the main shaft to the planetary. I completely rebuilt my unit. When I first fired it up it would tick in first and had no difference between 1st and 2nd gear. I loosened the nut on the planetary and same on the top of the shaft. 1st started working good, but second disappeared. Third works good. I'm assuming this is a trial and error process. I also learned that flipping the gear on the top of the main shaft could have catastrophic consequences.

    • @curtisneedham6083
      @curtisneedham6083 11 лет назад

      I should have mentioned that this unit was made somewhere in the lte 40's.

    • @charlesburow8120
      @charlesburow8120 5 лет назад

      Check all the keys to make sure none are broken. Ever time you open the transmission the shifter bushings and grease should be replaced.

  • @ivanbarroso2266
    @ivanbarroso2266 3 года назад

    Hola! Me he reservado su tutorial para siempre. Pero querría preguntarle si tiene usted algún tutorial para cambiar el cable elevador de la olla? El mío no eleva la cacerola y tengo que meterle un suplemento debajo para que las palas me lleguen a lo más profundo de la olla. Estaría muy agradecido. Por cierto! Es la misma máquina que expone usted en el video

  • @haroldcanoy2340
    @haroldcanoy2340 5 лет назад

    Mine doesnt have a screw on top. How do you open this cover guys?

  • @juanmanuelolveracastro4024
    @juanmanuelolveracastro4024 2 года назад

    Quiero saber cómo se desarma y se arma

  • @deansheridan
    @deansheridan 5 лет назад

    How in the heck do you remove the first key? He makes it look so easy

  • @abdullahmuhammad5496
    @abdullahmuhammad5496 7 лет назад

    need the wiring diagram for the on/off switch for A 200
    or location of the wires T 1 T2 T3 T4 Thanks

  • @javiermonzalvovelazquez5068
    @javiermonzalvovelazquez5068 4 года назад +2

    Hola amigo, yo tengo una crypto-peerless y la desarme para cambiar el engrane que va en el sin fin del motor, pero ahora no entra la 1, la segunda si entra bien y la 3 gira pero no tiene fuerza y empieza a tronar ( me refiero a no tener fuerza, es que gira pero lo puedo detener con la mano 1 y 3) la segunda trabaja bien, alguna idea de que puede ser, o algún video? 🤔
    Espero y me puedas ayudar amigo. Saludos desde México 🇲🇽

    • @lazarofuentes6386
      @lazarofuentes6386 2 года назад

      hola amigo !!! de seguro la has armado mal !!! es por eso, saludos

  • @16horses2004
    @16horses2004 7 лет назад

    I can't get the cover off the planetary. Any suggestions?

    • @owenwhitman6616
      @owenwhitman6616 6 лет назад

      1) Be sure all 4 cover screws are removed, as well as the nuts on the top of the shafts.
      2) If the gears have bound/locked-up you may need to manually roll-back (counter-clockwise as viewed from the front) the motor to release the tension.

  • @chadelliott8012
    @chadelliott8012 8 лет назад

    How did you remove the stainless steel ring around the planetary area?

    • @Longwood75
      @Longwood75 4 года назад

      Pull the ring down to remove it. It is held in place by friction from small spring loaded balls pressing against the inside diameter of the ring. If the planetary is removed, the ring should come down with the planetary.

  • @amadorvelasquez
    @amadorvelasquez 5 лет назад

    Tengo una de 20 litros ventus. El mecanismo es similar si me enseñan como alibrar. Por que se escucha un sonido de fierro. Gracias

  • @norbertwojke9282
    @norbertwojke9282 4 года назад

    looking for video oil change hobart meat grinder mod. 4812 does anyone know?

  • @anthonyguilianoii8836
    @anthonyguilianoii8836 6 лет назад +13

    I love how they say to use latex gloves and the guy in the video isn't wearing any gloves

    • @charlesburow8120
      @charlesburow8120 5 лет назад +1

      Anthony Guiliano II I found every time I pulled apart these mixers the gloves would catch on a burr on a gear and the gloves would rip open.

    • @alexelliott5022
      @alexelliott5022 Месяц назад

      They already cleaned the kilo of old grease out, gloves weren’t necessary anymore.

  • @snowdc5039
    @snowdc5039 8 лет назад

    WHAT TYPE OF GREASE I NEED TO USE FOR TRANSMISSION GEAR UNIT

    • @jaredj631
      @jaredj631 8 лет назад

      SNOW DC503 you need to use Mobile grease 222. It's hard to find you likely need to buy it from Hobart.

  • @aad1339
    @aad1339 4 года назад

    I have a problem, I've tried to change the first gear speed and cannot get it back. Can you help me?

  • @milojm1
    @milojm1 11 лет назад

    hello I speak of Argentina have a machine like and want to rebuild, seeking a gear, is the first of the little that is coupled to the main drive, and is the first speed, I have to send to make, or come to replace?
    thank you for your help, or if you have so far, can you give me the specification of gear

  • @filibertotrejo2446
    @filibertotrejo2446 7 лет назад

    tengo una igual le cambie el engrane d bronce pero no me ace Los cambios pueden desirme que sera

  • @filibertotrejo2446
    @filibertotrejo2446 7 лет назад

    hi I need help I have a similar machine but I need fix it I want to know if you can show me step by step how to open it and change the transmission

  • @gelordkavukatema3981
    @gelordkavukatema3981 2 года назад

    Great teacher 👍

  • @dwightsmall9970
    @dwightsmall9970 3 года назад

    Thanks for showing how to remove the gears.

  • @robertknight4672
    @robertknight4672 3 года назад

    Latex gloves aren't allowed. vinyl or nitrile.

  • @todor55
    @todor55 6 лет назад

    Hi Anand!
    are they compatible a200 and other 20 quart hobart mixer gear shifters,because my A200 has a broken flat handle and i find other from the newest models(with the black ball)..
    Can i replace it or they are not compatible?!
    Regards!

    • @charlesburow8120
      @charlesburow8120 5 лет назад

      Toshko you need to call your local Hobart office. The need the model number and the ML#(old units have SPEC #’s)

  • @user-sb2gh8du4z
    @user-sb2gh8du4z 5 лет назад

    Perfect! Just saved me 1800$!!

  • @alexgamboa8143
    @alexgamboa8143 3 года назад

    Hola buenas tardes necesito conseguir repuesto para esa batidora el muelle que ajusta las velocidades

  • @milojm1
    @milojm1 11 лет назад +1

    hola le hablo de argentina tengo una maquina igual y quiero reconstruirla, busco un engranaje, es el primero de los pequeños el que esta acoplado al mando principal, y es la primera velocidad, lo tengo que mandar a fabricar, o viene como repuesto?
    agradesco su ayuda, o si tiene la medida, me puede dar la especificacion del engranaje

    • @snowdc5039
      @snowdc5039 8 лет назад

      es aviene como repuesto lo puedes conseguir en ebay or Hobar mixer parts

  • @bernardolara9042
    @bernardolara9042 11 лет назад

    Thank you for the tips, excellent job !

    • @humbertoguerrero1741
      @humbertoguerrero1741 6 лет назад

      hola no puedo guitar la pieza para hacer la pizza dog esta standards donde puedo alla un lugar donde la remuaban

  • @filibertotrejo7927
    @filibertotrejo7927 6 лет назад

    Tengo una igual no hace los. Cambios me puede ayudar

  • @claragermiller7413
    @claragermiller7413 7 лет назад

    I lost speed #1 how do I fix it? Please respond

    • @anthonyguilianoii8836
      @anthonyguilianoii8836 6 лет назад +1

      Clara Germiller ... so you didn't watch the whole video? At 7:56 he answers your problem... I hope that was your problem. If not then I look stupid being sarcastic.

  • @rafaelsalazarcantor1993
    @rafaelsalazarcantor1993 8 лет назад

    tego una batidora de 40 litros mepuedes enseñar el mantenmiento de la kajad el bideo quemuestras es eselente grasias

  • @guillermoamartinez1
    @guillermoamartinez1 9 лет назад

    Hello, I have a mixer hobart a200 and is unarmed, I need information on connecting the starting coil motor and cables to the platinum condenser, best regards
    hola, tengo una mezcladora hobart a200 y esta desarmada, necesito información de como conectar la bobina de arranque del motor y los cables que van al platino y condensador, saludos cordiales

  • @HattabFatima-v2x
    @HattabFatima-v2x 5 месяцев назад

    قطع الغيار لهذا الخلاط

  • @drbeneamin
    @drbeneamin 11 лет назад

    Fantastic. Thank you.

    • @ibrahimka245
      @ibrahimka245 7 лет назад

      Dear Sir
      Please upload Gear box (Service) for my Hobart h 600 1800 step by step like others specialy how to joint the parts after removing

  • @CHOWIXCHANNEL
    @CHOWIXCHANNEL 5 лет назад

    Thank You 🙏🏻

  • @erneumann3136
    @erneumann3136 4 года назад

    Good video.

  • @musistecnico
    @musistecnico 2 года назад

    Que bien. Algunos pasitos faltaron😀😀

  • @tubekim777
    @tubekim777 11 лет назад +4

    Please upload GEARBOX(SERVICE) for my Hobart D300 step by step same like this one .
    one to know how to remove or open top of the gear box.
    Thank You

    • @rockgee
      @rockgee 9 лет назад

      +Sary Siv have you found a video for the Hobart D 300? I also need it.
      Rock

    • @vandalentim
      @vandalentim 6 лет назад

      @@rockgee have you find any videos? I have a A300 too and it needs some work. I cant even get the main nut from the shaft. It's so tight and the planetary will just rotate when I will try and loosen the nut. Any help would be great. Hobart tech manuals are not very helpfull in any case

  • @saulfuentes7073
    @saulfuentes7073 8 лет назад

    yo tengo una pero es sellada no se desalma

  • @marcosarmandoescamilladzul6893
    @marcosarmandoescamilladzul6893 10 лет назад

    thank yuo. very similar to a blazer b-10

  • @bsbagbbaba2807
    @bsbagbbaba2807 5 лет назад

    plz gub video model B-30N

  • @isaacmazack6675
    @isaacmazack6675 5 лет назад

    cant take out first gears

  • @blondorphanboy3874
    @blondorphanboy3874 5 лет назад +4

    the funny mixer

  • @LuisAlejandroRodriguezSusarret
    @LuisAlejandroRodriguezSusarret Месяц назад

    Amasadora,

  • @KitaC-u9c
    @KitaC-u9c Год назад

    My donut won’t come offf

  • @jwootton03588
    @jwootton03588 9 лет назад

    10/10
    Jack Wootton

  • @mohdjunaid7884
    @mohdjunaid7884 Год назад

    Wirering

  • @LuisBallesteros-hr8hw
    @LuisBallesteros-hr8hw Год назад

    Me gusta reparar estas maquinas

  • @wugner0118
    @wugner0118 Год назад

    Dont buy hobart. No support after sale service. Buy chinese brand in lazada.

  • @gloriacastano1437
    @gloriacastano1437 2 года назад

    Tienes un número telefónico