I just had to swing by and give you a huge shoutout for your awesome video on calibrating that motor. I was seriously pulling my hair out trying to figure it out, and your video was a total lifesaver. Your explanations were super clear, and I finally got that stubborn motor working like a champ, all thanks to you. Seriously, your channel rocks, and I can't thank you enough for being such a legend and helping out folks like me. Looking forward to more of your killer content in the future!
I was looking for a solution over an hour and i thought that my esc or motor is faulty but luckily i found this video and now it's working.Thanks man keep up the good work🙂
I didn't know about the calibration sketch that could be used. I am about to try that to see if it sorts my problem. Excellent video and explanations, from one teacher to another, thank you.
Waoooh..! Thanks. It works for me. But I have a question that what if I want to control that brushless motor in clockwise rotation and anticlockwise rotation how should I connect and code it.
Hello, thank you fore the video. I have been trying to figure this out for weeks, and I thought your knowledge on this would be helpful. I have tried every calibration code out there and with many different wire configurations, but my motor is only able to twitch back and forth when yours in the video moved as a normal motor. Do you have any idea on why this is?
Hi i am making a project on rc car in that i want to use 2 bldc motor for back wheel rotation whare both back wheel are connected to same shaft of 2 bldc motor i have some doughts 1)i am using esp32 to control the motor rotation and i am conncting joistick to enother esp32 that is in serial communication using wifi Is it possible to control speed and direction ⬇️⬆️ of bldc motor If direction can not be conducted so can i place 2 bldc motor in such a eay that 1 motor for forword ⬆️ and another for reverse ⬇️ direction 2) by connecting the servo tester to controler esp32 can i control speed on bldc motor from esp32 on bldc car side I am using 12v 18650 battery pack of 7Ah and 40A bms 3)How much time it min/max approximately can run 2 bldc motor with 12v 7Ah battery
Thank you very much 👏🏻👍🏻. Yes I am actively monitoring the activities on channel . I am in process of setting up things and will be back with new video soon 👍🏻
Nice video! I've tried doing the calibration but it keeps beeping as if nothing happened A constant beep, beep, beep (like that think that monitors heart beats on hospital)
Thank you very much for checking out the video 👌🏻👏🏻. You need to check the data sheet of the esc for this beep sound . These type of beep sounds indicate problems with connections . Please check . Also take a look at video again for any missing step 👍🏻👏🏻
@@hashincludeelectronics it seems that I bought one of those cheap esc from Ali express like XXD 30A with the brushless motor I can't find the documentation for that 😔
Can you make a drone using HC-06 BLUETOOTH MODULE cause I try making a drone with multiwii but am always have arming issues("I.e two motor arm while the other two don't arm and even if they do is when I have increased the value to 'High'"). And for the app am using RemoteXY, please I need your help to complete my project 🙏 thank you.
It can not be achieved directly with programming . We will have to use switch to actually change the wires of bldc motor . May be 2 relays . Let me see if I can do that 👍🏻👏🏻
Thank you so much I used a power supply @12.6 up to 5amp saturation current the problem that when I send max throttle 2000 it does not respond the acceptable range is from 1000us till 1100us ,, I used the same motor and ESC some times the current drops down after a few seconds and sometimes does not do you have an idea , Thank you so much again .
Hii Mate ! i want to run 2 Bldcs and a servo using a arduino and 2 joystick i needed help in the code I would really be thankful if u could help me with the code !!
You can use the same code and make changes to add support for 2 bldc and 2 servo motors . Just copy paste the code. Give it a try and you will be successful 👍🏻
@@hashincludeelectronics thankss a lot for ur help i will let u now for sure it it works i think after copy pasting i gotta change the serial ports then it should work Thankss for ur help ! 😊😊
Plz make a video on Arduino based drone we are waiting it will be a great help because your videos are very well explained and easy to understand And you also highlights some important points which are very informative
hello, is the 1000 - 2000 value fixed for all the ESC or does it change depending on which ESC I own? In some other videos I also saw that they where using 0-180 as value
@@hashincludeelectronics but is 1000-2000 standard? I have a 400Ampere 12s ESC that I need to control with a Potentiometer. Are there any already made circuits to convert the voltage from the potentiometer to the PWM for the ESC without having to program and using the Arduino?
Thanks for checking out the video 👍🏻. Could you please add your comment on esp32cam video so it will be easy ? Let me know what issues are you facing there .
Guys I want you to help me on how I'm going to write this code with Arduino Uno R3 I want to control 2 bldc Motors and 2 servoMotors with Arduino so I want the Arduino to generate pwm at 4 different digital pins.so I want to control them with four potentiometers at input on pins is A0,A1,A2,A3'if anybody can help thank you
![Natanael Cano - Amor Eterno [Official Video]](http://i.ytimg.com/vi/EO4prCs6WpM/mqdefault.jpg)
The only guy that tested a brushless motor without servo tester or transmitter
Thank you very much for checking out the video and nice comment 👍🏻👏🏻
I just had to swing by and give you a huge shoutout for your awesome video on calibrating that motor. I was seriously pulling my hair out trying to figure it out, and your video was a total lifesaver.
Your explanations were super clear, and I finally got that stubborn motor working like a champ, all thanks to you. Seriously, your channel rocks, and I can't thank you enough for being such a legend and helping out folks like me.
Looking forward to more of your killer content in the future!
Wow . This means a lot . Thank you very much for checking out the video and I am glad that it helped you 👍🏻👏🏻👏🏻. Stay tuned and keep learning 👍🏻
Same huge thanks
I was looking for a solution over an hour and i thought that my esc or motor is faulty but luckily i found this video and now it's working.Thanks man keep up the good work🙂
This is really awesome . I am glad that this video helped you . 👌🏻👍🏻👏🏻
I didn't know about the calibration sketch that could be used. I am about to try that to see if it sorts my problem. Excellent video and explanations, from one teacher to another, thank you.
Thank you very much 👍🏻👏🏻
Thanks, Very good explanation. Could you do also video, how to "Set all functions to factory defaults" to that ESC?
Waoooh..! Thanks. It works for me. But I have a question that what if I want to control that brushless motor in clockwise rotation and anticlockwise rotation how should I connect and code it.
It can not be done programmatically. You have to manually switch any 2 wires of brushless motor connected to ESC .
In the same circuit, I will make a 3s2p connection instead of Lipo battery. Should I buy 20A bms or 10A?
Hello, thank you fore the video. I have been trying to figure this out for weeks, and I thought your knowledge on this would be helpful. I have tried every calibration code out there and with many different wire configurations, but my motor is only able to twitch back and forth when yours in the video moved as a normal motor. Do you have any idea on why this is?
I would suggest to follow exact step in video . It’s very simple to calibrate it . Check how and when I provided power supply 👍🏻👏🏻
Super helpfull video👍
Thank you 👍🏻👏🏻
Having problem of BLDC when using Xboxusb host shield to control it
Great, Can we make the Joystick control the motor in both directions? ( Motor move forward and backward)
Unfortunately we can not reverse the direction programmatically for BLDC motor 👍🏻👏🏻
With those components in the video can you make the motor rotate in the opposite direction?
No rotating the bldc motor programmatically not possible 👍🏻👏🏻
Hi i am making a project on rc car in that i want to use 2 bldc motor for back wheel rotation whare both back wheel are connected to same shaft of 2 bldc motor i have some doughts
1)i am using esp32 to control the motor rotation and i am conncting joistick to enother esp32 that is in serial communication using wifi
Is it possible to control speed and direction ⬇️⬆️ of bldc motor
If direction can not be conducted so can i place 2 bldc motor in such a eay that 1 motor for forword ⬆️ and another for reverse ⬇️ direction
2) by connecting the servo tester to controler esp32 can i control speed on bldc motor from esp32 on bldc car side
I am using 12v 18650 battery pack of 7Ah and 40A bms
3)How much time it min/max approximately can run 2 bldc motor with 12v 7Ah battery
Thanks! You saved my day!
You are welcome!
Thank you. I would appreciate if you tell us: can we reverse the rotation of the motor?
No we can not reverse the rotation of motor 👍🏻
@@hashincludeelectronics I have seen bi-directional esc...
Thank you, it helped a lot. You have a lot of interesting videos. Are you planning to come back to yt?
Thank you very much 👏🏻👍🏻. Yes I am actively monitoring the activities on channel . I am in process of setting up things and will be back with new video soon 👍🏻
Nice, but I want a exoskeleton for this figure that I’ve created.
Thanks man for this video
You are welcome 👍🏻
Nice video!
I've tried doing the calibration but it keeps beeping as if nothing happened
A constant beep, beep, beep (like that think that monitors heart beats on hospital)
Thank you very much for checking out the video 👌🏻👏🏻. You need to check the data sheet of the esc for this beep sound . These type of beep sounds indicate problems with connections . Please check . Also take a look at video again for any missing step 👍🏻👏🏻
@@hashincludeelectronics it seems that I bought one of those cheap esc from Ali express like XXD 30A with the brushless motor
I can't find the documentation for that 😔
Can you make a drone using HC-06 BLUETOOTH MODULE cause I try making a drone with multiwii but am always have arming issues("I.e two motor arm while the other two don't arm and even if they do is when I have increased the value to 'High'"). And for the app am using RemoteXY, please I need your help to complete my project 🙏 thank you.
hello can i ask a question, can you make bldc motor turn in reverse too?
It can not be achieved directly with programming . We will have to use switch to actually change the wires of bldc motor . May be 2 relays . Let me see if I can do that 👍🏻👏🏻
Thank you so much
I used a power supply @12.6 up to 5amp saturation current
the problem that when I send max throttle 2000 it does not respond
the acceptable range is from 1000us till 1100us ,, I used the same motor and ESC
some times the current drops down after a few seconds and sometimes does not
do you have an idea ,
Thank you so much again .
You need to use good lipo battery for BLDC motor. LiPo battery has Capacity feature which can provide spike in current needed by BLDC motor.
@@hashincludeelectronics
Thank you, I will try,,
❤️❤️
@@RESC_Eng good luck 👍🏻
Can we rotate it in both directions, clock wise and anti clockwise
It’s not possible programmatically. However you can reverse the direction manually by interchanging any 2 wires of motor 👍🏻
thx i love u guy
Thank you very much for checking out the video 👍🏻👏🏻
Is your ESC heating so much at 3S voltage batrery?
No . It’s running fine .
Can this setup be used to control torque on the motor?
Give it a try 👍🏻👏🏻
Hii Mate !
i want to run 2 Bldcs and a servo using a arduino and 2 joystick i needed help in the code
I would really be thankful if u could help me with the code !!
You can use the same code and make changes to add support for 2 bldc and 2 servo motors . Just copy paste the code. Give it a try and you will be successful 👍🏻
@@hashincludeelectronics thankss a lot for ur help i will let u now for sure it it works i think after copy pasting i gotta change the serial ports then it should work
Thankss for ur help ! 😊😊
Plz make a video on Arduino based drone we are waiting it will be a great help because your videos are very well explained and easy to understand
And you also highlights some important points which are very informative
Thanks for awesome words 👌 Sure I am working on it.
@hash include electronics Does it work with sensorless BLDC motors as well?
I believe it should work .
is there a way to make it reverse when the joystick goes down ?
No it’s not possible programmatically. 👍🏻👏🏻
what component is needed in order for it to reverse ?
hey can i use a potentiometer instead of joystick
Yes you can . However the speed will only increase when potentiometer is past half way 👍🏻.
hey i tried but my motor is not running it only beeps 2 times then not running plz help i used a dvd writer bldc motor
😳 amazing.
Thank you very much 👏🏻👍🏻
Make drone using Arduino and Nrf module with bldc motor
@@kathanpatel8081 sure will do 👍🏻👏🏻
Hi!, is it possible to change the motor rotation direction from the code?(using a suitable ESC) Thanks!
No it’s not possible . You need to interchange the wires physically .
Maybe inrunner motor can go reverse
hello, is the 1000 - 2000 value fixed for all the ESC or does it change depending on which ESC I own? In some other videos I also saw that they where using 0-180 as value
Yes . 1000-2000 is the range in microseconds . The servo library also uses values in degree i.e 0-180 which maps to 1000-2000 microseconds.
@@hashincludeelectronics but is 1000-2000 standard? I have a 400Ampere 12s ESC that I need to control with a Potentiometer. Are there any already made circuits to convert the voltage from the potentiometer to the PWM for the ESC without having to program and using the Arduino?
Esc unit can run on 24V dc ?
Please check the specification of your esc and bldc motor . 👍🏻
Same code if im using a rc car ecu interested of drones?
Yes same code 👍🏻
It cant use servo?
Yes you can use servo as well 👍🏻👏🏻
I have seen all you videos but in the video of esp 32 cam car the app is not working
Thanks for checking out the video 👍🏻. Could you please add your comment on esp32cam video so it will be easy ? Let me know what issues are you facing there .
What is the total cost of this project
You can easily add the individual components cost and get the total 👍🏻👏🏻
How can i control the direction of the this specific motor ?🌹
For direction change you have to interchange any 2 wires out of those 3 wires connected to motor .
Can you make next video on drone
Sure. Actually I am working on it . But it will take time . Stay tuned and soon in future you will get this video 👍
I did all the connections and try the calibration code it beeped alright but the motor didn’t start pls help me
Upload the other code and see if it works with joystick after calibration.
@@hashincludeelectronics ok
i tried it but still not coming
Guys I want you to help me on how I'm going to write this code with Arduino Uno R3 I want to control 2 bldc Motors and 2 servoMotors with Arduino so I want the Arduino to generate pwm at 4 different digital pins.so I want to control them with four potentiometers at input on pins is A0,A1,A2,A3'if anybody can help thank you
This should be simple to code . Guys please anyone could help here ? Thanks 👍🏻👏🏻
Can i make a drone using these
And how much voltage would i need if i am using a nrf24 /bt hc05, mpu6050 and the arduino i mean like is 11.1v with 2200mAh enough
Oh and i forgot its a 1400kV motor
hi bro joystick control in 2 direction ?
No it can not . You need to interchange the motor wires manually to reverse the motor rotation . 👍🏻👏🏻
reverse direction ?
You can do it manually but not programmatically. Just interchange any two wires to motor 👍🏻
👍🏻
👍🏻👌🏻
Aise Mera bldc motor chal raha hai
Par receiver se Nehi chal raha hai acchase
It should work with receiver as well . Make sure you use proper code .
@@hashincludeelectronics servo motor chal raha hai par bldc motor chal Nehi raha
Its not working for me
What issue are you facing ? Please check the video slowly and carefully for any missing step 👍🏻👏🏻
Dron programing code sher pilis