Crazy your timing came right into line with my car that I told ya about the previous video, glad it all worked out. I'm sure it'll run the number your looking for now, don't change anything.
New Subscriber here. Wondering if you are going to make it to Sick Summer? I'm in and this is my first drag -n-drive event. Cordova is my home track, and I am in the Quad Cities. Hope to meet you if you make it
I’m not sure exactly what my plan for the summer is! I’ve been battling converter stuff since my motor failure at sick week last year. Definitely gonna do some drag and drives in the future just gotta get this rig happy and fast again! Hell ya man I hope to make it to Cordova for one of the races at least this summer. Ill keep the RUclips updated. It’d awesome to meet ya!
How much hp and boost can a ly6 take bored to ls3. 4340 fordged rods and pistons. 4500 lb truck..? 7000 max rpm is the timing table below a safe place. For the forged pistons and rods. Stock crank cap. Arp stud and cap bolts 1-4000 rpm 15 psi. 20 degrees of trimming 4100- 7000 24 psi - 20 degrees
I dont think it's a coincidence that you said your last set up was 7 degrees off, then ended up adding 6 degrees on the dyno. The power difference is almost exactly what it needs to go from 5.4s back to 5.17s. Might have been a mistake when verifying timing on last set up, and it actually had more timing than you thought.
It all depends. If the timing is verified, sometimes they don’t like timing other engines do. Just gotta find the sweet spot. I pulled 2* out of the back 2
With my 4400 lb car sbe 6.0 gen 4 Can i set 13 degree timing at 30 psi boost 15 degree timing at 25 psi boost 20 degree at 10 psi. Boost 30 degree of timing before boost kick in . Would this be safe?
@OverydeMotorsports Correct if im.wrong. At 30 psi 10 degree 6500 and below 14 degree 6600 to 7200 At 25 psi 11 degree 6500 and below 15 degrees 6600 to 7200 At 10 psi 16 degree 6500 rpm and below 20 degree 6600 to 7200 rpm At no boost 27 degree to 6500 rpm below 30 degree 6600 to 7200 What is shift drop? How do i.make sure it is not large. How do I increase and decrease? What is the idea value.?
If i upgrade the gen 4 rods to forged rod 4340.... and keep factory pistons... can i run 15 degrees of timing below 6500 rpm @25 psi and 20 degrees above 6500 rpm @ psi... Same 4400lb car... What table do you recommend? @OverydeMotorsports
that's a lot of horsepower, it worries me a little, i'm going for a completely different stagity and i'm just looking to get in the 10s but still.... 1200 HP is a lot more than anything i ever dreamed of.
Crazy your timing came right into line with my car that I told ya about the previous video, glad it all worked out. I'm sure it'll run the number your looking for now, don't change anything.
Right!! I need a test day now! Damn north it’s so cold up here!
Post a link to the dyno shop!
Not really a shop, but Steven Kiehne on Facebook
Awesome, thanks for sharing information on timing.
Good stuff! She’ll scoot now I’m sure! Enjoy following the build
Thanks man!
Awsome video man! I love the SBE stuff and seeing how hard y’all can push them but still keep them alive 🤟🤟
Thanks brother!!
Hey! Would you be willing to go through some datalogs from the dyno pulls?
Just seen your stunt double at the pad!!!!😁😁😁
I gotta find a video and check it out!
@@OverydeMotorsports hildagofilms!!!
New Subscriber here. Wondering if you are going to make it to Sick Summer? I'm in and this is my first drag -n-drive event. Cordova is my home track, and I am in the Quad Cities. Hope to meet you if you make it
I’m not sure exactly what my plan for the summer is! I’ve been battling converter stuff since my motor failure at sick week last year. Definitely gonna do some drag and drives in the future just gotta get this rig happy and fast again! Hell ya man I hope to make it to Cordova for one of the races at least this summer. Ill keep the RUclips updated. It’d awesome to meet ya!
Here I am worried about 15 psi on my 5.3 . This guy gives me hope
Hahah let it rip if it’s a gen 4!
@@OverydeMotorsports gen 3
I just want 800 wheel
@@RogueKing86 800 wheel is nothing for a gen3 watch Richard Holdners big bang theory
Look in to the Black Sheep waste gates!
Will do!
I was gonna say the same thing.. Turbo John got a pair and loves em.. Boosted Lifestyle
How much hp and boost can a ly6 take bored to ls3. 4340 fordged rods and pistons. 4500 lb truck..?
7000 max rpm is the timing table below a safe place. For the forged pistons and rods. Stock crank cap. Arp stud and cap bolts
1-4000 rpm
15 psi. 20 degrees of trimming
4100- 7000
24 psi - 20 degrees
Maci and I both watched the video on our way to a cheer competition lmao. Good numbers man!
Hell ya!
I dont think it's a coincidence that you said your last set up was 7 degrees off, then ended up adding 6 degrees on the dyno. The power difference is almost exactly what it needs to go from 5.4s back to 5.17s. Might have been a mistake when verifying timing on last set up, and it actually had more timing than you thought.
It very well could, have. I’ll double check it again just out of curiosity.
Impressive timing and numbers for e85
Oh for sure! That one seemed to like timing
How much do you think the heads are helping power wise over stock? Love this sbe stuff
This was actually on stock heads. I wanna do a direct comparison this spring on them
Those are very impressive numbers for a sbe 5.3. Is it on Methanol or e85?
E85 for now hahah
I think once you get the converter Straightened out that will be one bad hot rod
I sure hope so!
28?? Trying to break it lol
It’s got more room to go!
New sub here what intake you run
Thanks, Holley Hi ram with a 417 lid
What do you think about ptc 18-0, 9.5 converter?
My old car had that. It was good. Tight enough to be fast and loose enough for it to not dog out
is this a gen 4 5.3 like a lmg or lm7?
Lc9
sheesh is it really stock bottom end? or it has piston rods ? but its running nice
Nope that was a stock rods crank and piston deal in an iron 5.3
I would of swore this was on methanol....that much timing and boost on e85 is crazy without an intercooler
It has a intercooler. It’s a2w behind the bumper
what fuel system? what pump and injector combo ?
In this video it was a aeromotive 5.0 and Bosch 210s. Later it was 3 525s and same injectors
So who is the dyno guy and where
is he located
Steven Kiehne, he is out of zumbro falls mn
Nice work. Suprized how quick the 102 lights off. What cam did you choose for it? She will be an animal on M1.
Right! I wanna try it! It’s a custom one a little more aggressive then a btr stage 4
@@OverydeMotorsports M5 even better but 💸
@@OverydeMotorsports I got btr stage 3 boost cam that will work good on my 6.0 gen 4 on 91 mm and holley hi ram?
What was your timing table. What individual cylinder stuff did you do. Want to do 11xx hp on gen 4 6.0 sbe in a 4400 lb car, street -strip ..
I pulled 1* out of cylinders 7 & 8 and added 2% fuel. I’m at 16* at 32lbs. That is a heavy car tho I would be very careful with timing
How much timing do you recommend with this 4400 lb car?
@@OverydeMotorsports how much timing in Cylinder 7& 8?
@@OverydeMotorsports what type of rocker arms and valve springs. Without floating?
It all depends. If the timing is verified, sometimes they don’t like timing other engines do. Just gotta find the sweet spot. I pulled 2* out of the back 2
Good numbers... What turbo you running?
Vs racing large frame gt55
@@OverydeMotorsports Great Build!
Thank you!!
Nice job . When you have 19 degrees of advance at 21psi does that mean that’s the max of advance or do you increase that as the rpm’s raise?
It’s lower in peak torque area then up to that in the peak power area
Is the hood custom made?
Yessir
What did you run for ring gap?
.03 and .032
What heads ? Ported??
Stock 799s
What type of cam?
Custom, slightly more aggressive then a btr stage 4
Do you race with pump e85 or do you use vp x85 or something?
Pump e85
How much does the car weigh?
With the iron block around 3150
What plugs are you running and gap at the 30lbs of boost?
B8efs at .016
@OverydeMotorsports what is part no. What gap, timing, and boost you recommend on 6.0 same set up..
What was the timing at 14.7? Thanks
19.5*
@@OverydeMotorsports Thanks. Maybe I'll see ya at rock falls in the spring
@@bbcnova56 hell ya come say hi!
What rings gap.
.03 and .032
What brand dyno was it tested on?
Dynocom
What was max rpm?
8200
With my 4400 lb car sbe 6.0 gen 4
Can i set
13 degree timing at 30 psi boost
15 degree timing at 25 psi boost
20 degree at 10 psi. Boost
30 degree of timing before boost kick in .
Would this be safe?
That’s a heavy rig! I would lower all those numbers by 3 or 4 until your above 6500rpms and make sure the shift drop isn’t to large. That bends rods
@OverydeMotorsports
Correct if im.wrong.
At 30 psi
10 degree 6500 and below
14 degree 6600 to 7200
At 25 psi
11 degree 6500 and below
15 degrees 6600 to 7200
At 10 psi
16 degree 6500 rpm and below
20 degree 6600 to 7200 rpm
At no boost
27 degree to 6500 rpm below
30 degree 6600 to 7200
What is shift drop? How do i.make sure it is not large. How do I increase and decrease? What is the idea value.?
If i upgrade the gen 4 rods to forged rod 4340.... and keep factory pistons... can i run 15 degrees of timing below 6500 rpm @25 psi and 20 degrees above 6500 rpm @ psi... Same 4400lb car...
What table do you recommend?
@OverydeMotorsports
1570 crank on a stock bottom end is bonkers.
Hahah sure is
that's a lot of horsepower, it worries me a little, i'm going for a completely different stagity and i'm just looking to get in the 10s but still.... 1200 HP is a lot more than anything i ever dreamed of.
It’s a lot of power! But it can get spendy in a hurry!
What sbe is this??
I don’t even know lol, it’s a gen 4 iron block 5.3. I’m not sure what year or what it was even out of
Stock?
Yep gen 4 5.3
What’s the afr 20 lbs and up?
11.0 on the gas scale. It’s on pump e86
What head bolts your running?
Ca625 arp studs. Just the stock m11 thread size
@@OverydeMotorsports what size turbo