Easy to make tyre bead breaker
HTML-код
- Опубликовано: 15 май 2014
- Easy to make tyre bead breaker tool
Disclaimer
Due to factors beyond the control of backstreetmechanic, It cannot guarantee against improper use or unauthorized modifications of this information. backstreetmechanic assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. backstreetmechanic recommends safe practices when working on vehicles and or with tools or equipment seen or implied in this video. Due to factors beyond the control of backstreetmechanic, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not backstreetmechanic. 
Хобби
I will have to try this as I'm poor and in need of a tire change , thanks from Ohio 👍👍
Normal people are so fecking ingenious, great idea you had there.
I liked this, then I noticed my claw hammer looked very similar. Turned out it worked a treat on my 600 cc motorcycle rear tire. Careful to either keep the claws just off the rim or wrap some protection over them. I used a 2lb lump hammer working over about 8 inches.
People who can ,DO. People who can"t teach , you did good
Nice video + idea!!! The only downside for me is the welding part.
Excellent tool. I've been having trouble with some tires and this might be what I need to get them loose
What I found with mine , lift as you hit with the hammer. The action is much like using a “cats paw” to remove nails. Requires less force of hitting and uses the leverage of the tool. Good job ! 👍
great video, I have watched your videos on mig welding, when do you choose the arc over the mig welder? Thanks
I like the Go Green Air Pump. It works anywhere you take it to. Great video.
Have you used it on big low profile alloys? I found them to be really difficult to do and much tighter than steel wheels. I did a couple recently with a big piece of 3 x 2" as a lever but I even struggled with that.
Awesome tool!
Deadly man... Keep it up...
Excellent video showing how to get stuck in, must say however my local tyre place fitted me a new valve free of charge, fair play to you for your industry , the word "no" isn't used much apparently !MIke Williams.
...молодец мужик!!! Самый простой способ, при минимуме инструментов и приспособлений. Пойду сделаю себе такой же. Greetings from Russia
Awesome diy tool!
Nice job , I like it.
Awesome idea, I might have to make me one of those.
Very good stuff here sir thanks for the share.
Tool of that sturdiness & quality will set you back $100 or more, even just going through Harbor Freight. Nice.
Screw a spare valve stem into your valve tool to make a great handle and to have a new spare valve and stem to hand. Makes it much easier to use,no dropping valve cores !
was yawning to much cha cha cha, then hand held tire pump came into view and DAMN! MY RESPECTS @ 5:03 looks like nail but might be cob web HAHAHAHAHA i Like, OLE' !
Damn nice job man
Did you get compressor
Well done. 👍
That is one rusty wheel. Is that on a farm implement?
Wouldn't rolling the tool on the tire break the bead instead of hitting it?
good man
very nice tool
Very nice 👍👍👍
Makes it easier to break the bead when you lube with watered down soap. Good tool though.
Nice talented!
Sencillo y Funciona pero prefiero fabricar algo como el bedbuster XB454, no necesita tantos golpes
great price easy to set up.
You can actually replace the valve without touching the tyre at all. There's a tool for doing it.
good
Not recommended for Alloy rims.
im gonna use a old leaf spring and hammer .
That device used that way could gouge the bead area of the rim and you get a slow leak .
Driving your car over the tyre edge is safer and easier than that .
No Officer that's not a weapon it's my bead breaker , lol.
Неплохо
QUE LOS VIDEOS SEAN EN ESPAÑOL QUE HAY PERSONAS QUE NO SABEN
INGLES
Here is an idea. Instead of suggesting everyone should learn Spanish just to please you, how about you learn English? Well. you probably won't understand what I just said either.
Lol you can afford a welder but not a compressor
He's not coming anywhere my alloy wheels
The chances of "Setting the bead" on a tubeless tire with a hand pump are almost nill to nonexistent!
I would agree but in this case he only popped one side and the tire is wide enough to pressure the bead to the rim, im sure he most likely still had a hell of a time getting it to seal enough to pop
wrap a racheting load tie down strap around the tire and tighten it until the tire is tight on the wheel. apply air.
I've done that before. starting fluid and a grill lighter is more fun, you forgot to add, after it beads let the air out before removing the ratcheting strap, almost lost a finger once leaving pressure in the tire when I removed the strap
albeit good juggad
Tyre fitting has moved on...this type of tool will damage both tyre bead and wheel rim, best to leave tyre fitting to professionals who use the correct equipment.
okay mr kwikfit whatever you say
is a fake,,,