Precor Treadmill & Elliptical error codes and club settings
HTML-код
- Опубликовано: 7 фев 2025
- Access error codes, manager mode, diagnostics, Club settings and more.
www.coloradocardio.com
#coloradocardio #coloradofitness #gymmotivation #homegym #gym #colorado #elliptical #Coloradogym #treadmill #precor
Great stuff - you guys are a real life saver. This all reminds me of the "right to repair" battle farmers are fighting with the tractor manufacturers. The manufacturers don't want us to repair our own equipment - just toss it and buy a new $6,000 treadmill at the sign of the first error message or sign up for an expensive maintenance plan for a "factory" trained technician. Many of these errors are relatively easy to fix - thanks to the videos you guys put out.
Awesome to hear
What about a stuck key for the treadmill?
Great video! I'm having an issue with one of our precor treadmills.. There is a latch that pops up right behind the red STOP button and will not stay closed. Probably a simple fix I hope!
Replacement part:
Emergency Stop Switch Assy.
Our Part# PRT1122
OEM# 302525-101 or PPP000000302525101
gympart.com
Can you help me with a stuck key code and how to fix?
Can i ask you i I have a problem when I turn on the machine and start running, two minutes pass and the machine stops rotating because there is no one on the machine. The machine shows a message that there is no one on top of the machine. I have to press quick start to start it again and then it stops after two minutes and repeats the process, knowing that I am running on top of it. How can I cancel this system?
Great Info! Where is the reset button on the 946i Treadmill?
It is on the lower right or lower left, it might be worn out from a lot of use over the years.
Thank you for these videos, although I am hoping you can help me with a treadmill I just purchased second hand. I am new to these machines, but no stranger to distance running. I’ve tried entering codes to change the time limit on my Precor C956i model. It stops after an hour and enters cool down mode. This is fine for shorter runs, but a few circumstances have me needing to get most runs done on this vs. outside on trails like usual, and for my long runs I have to start it over to get the mileage. I’ve tried manually telling it 15 or 20 miles, but it will still stop at that 59 minute/hour limit. My machine doesn’t have a number pad like the machines in your video, it’s a single row of numbers above the QuickStart button instead.
If the time restriction is unavoidable I’ll manage. I love this machine and specifically wanted a really solid sturdy piece of equipment, that was my priority over any bells and whistles and I feel this one checks that box. The guy also sold it to me for $150 since he was moving and needed it gone ASAP. I didn’t do as much research as I would usually do before making this purchase, so didn’t think to check for a time limit. Thank you in advance!
You can change this in club settings, Precor has programed all their cardio equipment the same from the beginning. On your treadmill it's no different just use the number pad the same way. ruclips.net/video/__8ygPU0K2M/видео.html Here is a video I just made for you showing your model. Thank you - Colorado Cardio-
@@coloradocardio thank you for the reply and video! It took me a few tries, and looks like I was on the right track just had to enter in the code faster. On my machine it makes no indication if a button is hit or not, other than seeing it come up on the display. I now have it set for no time limit, appreciate you taking the time with a detailed answer!
I have a treadmill with a p30 console which tells me "use another routine" on the screen, and I can't get it out of there. I already checked connections and everything, and that message doesn't come out. What could be the problem?
I don’t have error codes but I’m having an issue finding a replacement power cord for a couple that need replacing at my friends gym. I’m not sure of the serial number but it looks almost like the second one you put the numbers in on. Or if you could tell me where to find the serial number I could tell you, thanks for the help
Hi there,
We have a precor elliptical, error code 80 when adjusting.
Many thanks
Hi i have a white screen on one and the other one the screen keeps resetting on off what could i do thank you
It's going to need a new IFT mother board box, which is located below. ebay has them for 300$ or send it in for $200
Precor elliptical with a blank screen already replaced the battery?
You need a new IFT box lower motherboard. ebay has them for 300$ or send it in to gympart.com
The fans by the motor won’t stop running. They are always on. Any idea why they won’t shut off? They’ve been on constant for a week now.
these fans should go off once they reach a specific temp. you might have a dust build up where it can't cool itself down.
@@coloradocardio they stay on all day. It is dusty under there, but is there a specific place I can dust to make sure it’s that?
How do you access diagnostic mode on a Precor TRM 885 Treadmill which does not have physical number buttons - only a touchscreen. It does have a pause button, but not other physical buttons.
I have this video as well:
ruclips.net/video/_mjqnOpmGr4/видео.html
Wondering if you can help? When I shut down circuit or unplug treadmill i get hit the stop button. I pull the cord and push it down. It says reseting and then goes blank. It will not take the Pause, 6, 5 and just stays blank. Thank you
Buen día, podría ayudarme con un código por favor, fue de gran ayuda su video :)
Error code 61. We moved it. Before we moved worked great. Now I got nothing.
Has been sitting turned on and idle for 6 months and now My console says "Temporarily Unavailable. Please Use another Machine". I think I have a p80
I would try a hard rest, turn off then unplug for 10 minutes. Plug back in and Turn back on. If this doesn't do anything your motherboard might have been damanged
Hello my precor efx 546 is showing a error code 09 if i disconect from the back sometimes it will fix it self by pulling the power cord in the back and waiting 30 sec or so but if i just try to reset it with the with the back switch it just keeps saying error code 09
Make sure it is plugged into the correct port on the back.
Plis error 40 help! 🙏🙏🙏
Mine just displayed that code too and the incline no longer works.
Hello - I have a Precor c956 treadmill that keeps saying stuck key. I believe it is the upper PCA that needs to be replaced. Do you have any guidance?
It is having trouble your stop key and the upper keys reconnect everything in the back to make sure good connections.
My elliptical won’t let me choose the workouts just goes blank. Do you know how to fix it. ?
Upper motherboard is going out or has went out. Need to send it in to National Gym Supply www.gympart.com
whats mean odometers that's the message i get when i push reset 65 thanks
That tells you how many total miles are on the treadmill
@@coloradocardio precor 956i error 12
I'm getting a consistent Error Code 82 -- any help on fixing this issue?
I have a EFX 5.23 elliptical that does not have a number pad. The manual states the keyboard is numbered 1-7 of the keys on the bottom, but there are 9 keys and I've tried every combination. What are keys 1-7 for the EFX 5.23?
You are on the right track however it does have to be fast and continuous. It'll take a couple trys.
Precor treadmill model 9.27 with a screen that says error 26, any fixes or issues that I can do without calling manufacturer?
The speed sensor is not responding the way it should, you might have dirt or debris in the speed sensor where is cann't reed the speed correctly. Try to blow out or vacuum underneath the hood where the drive motor is. this is where the speed sensor will be.
How do you fix an error code 82?
it gave me the same error. I bought a used product. When I opened the top cover, I saw that the cable on the screen was crushed between the cover. now i closed it by correcting no problem for a few days. I hope the problem is there.
Great advise.
Thank you sir
Hello,
I have a problem with pause bottom it doesn’t work
how can i fix it thanks
You need a new keypad over lay you can buy them at www.kamway.com or www.fitnessgraphics.com
I have a precor 635 efx elliptical with the P30 console. 475 hours and getting error 82 when adjusting resistance. I’ve cleared the codes but same result. Any suggestions?
It is your paddle switch; it has gone bad or got water in it. You can replace it from www.gympart.com
Can you help me with how to fix Precor Elliptical Error Code 44?
Lift motor is going out, might need to replace it.
How do u remove an error that says stuck key?
A stuck key is a sign that one of the buttons was pressed too firmly, and you will have to replace the overlay cost is approx. $75 www.kamway.com
Hello sir. We have PRECOR all touch screen treadmill. It's indicating Temporary Unavailable. How can I reset or fix? Thank you.
With the touchscreen Precor you can get into the back menu and find out the errors code and see what is causing it. Most cases this will be an error in the 30's which is communication problems. Most likely you will need to replace the IFT motherboard down below.
This is a valuable resource. Thanks. What does the ERR01 Code require as far as a solution? Thanks
Issue Symptoms
Errors 00 through 04 check upper PCA memory locations, RAM memory locations, and the EEPROM checksum
during the power up test sequence. If a fault is found during the power up test sequence, the appropriate error
code will be displayed.
While rare, these messages may display intermittently due to external causes. If the unit's AC input significantly
dips during the power up test sequence the test could fail resulting in triggering one of these errors. In addition,
treadmills operating on non-dedicated branch AC circuits may see these errors on an intermittent basis.
Troubleshooting steps
1 Reproduce the error and evaluate
a. Turn off unit.
b. Turn on unit. Repeat.
c. If the error message is consistently displayed when the unit is powered up, replace the upper PCA
This is and Upper PCA board Problem, turn off and disconnect the communication cable from the top going down to the lower motherboard. Reconnect it securely and turn the unit back on. If the problem comes back on you will need to send it in for a repair
@@coloradocardio Thank-you!
Hello i have error 27 the deck is not severely worn? Please help
Error 27 is motor current too high, there is too much drag on the running surface. apply silicone underneath the running belt and that should help it the drive motor is not broke
@@coloradocardio Hi thanks for reply. I lubricated last week. Any idea what else? Thanks
@@Echo-mz6tz your motor might be failing. Repair or replace
I don't know what to do my Precor treadmill I turn it on one morning it elevated then it showed error code. I unplugged and it don't show anything on the screen it only makes a clicking sound.
What to do?
You will need to replace the IFT box (Lower Motherboad)
Hi sir, i have TRM 631/661/681. We just transfer a location and whe i turn it on there is caption saying "press reset button" i press everything i seen in youtube but nothing happened. Please help me fix the problem.
The button has become disconnected, check connections.
No user detected comes up on screen ?? after 1.5 minutes cuts off
Give solution for 954i error 20
Too much power draw from the wall, it needs to be on its own circuit, without anything else pulled into that circuit/wall plug. and no extension cords.
How do you reset?
Only way for a precor is turn off unplug and plug back in and turn on
I have error code C-052-000?
Hey brocan you reset the odometer to 0
Not on Precor you can't
Precor 954i error 20 means
Motor Will Not Start / No Motor Movement Detected Applies to All AC drive motor treadmills Issue Symptoms The treadmill is monitoring the motor movement, through current monitoring. If the lower PCA does not detect that the motor is moving an error 20 will be displayed. This can be caused by a disconnected drive motor, or a very heavy user standing on the belt while starting. Troubleshooting steps 1 Verify motor connector is connected to drive 2 Check machine for stalling during operation 1MPH through 6MPH 3 Check error log for motor current during fault - If it is very low, check the connector and contacts, if it is over 7amps, it is likely a true stall condition 4 Check belt rating and current draw of treadmill - replace belt and deck if necessary.
Apply treadmill silicone underneath the running belt
Precor 956i have erro 12 and 30.
It's a lower PCA motherboard, error 12 and 30 both point to the lower motherboard being bad. Needs to be repaired and replaced..
I don’t have a pause button on my PrecorEfx53/i
Correct on those models you don't have that option.
Hi, I have an elliptical 5.21i with error code 30. Any tips? Thank you!
Communication cord is being pinched somewhere or not making a good connection
Error codes 30 and 32 on stationary bike 846i? TIA!
Errors 30 through 33 all indicate the loss of communications or erratic communications between the
microprocessors in the upper PCA and the lower PCA. The troubleshooting procedures for all of them are
essentially the same.
• Error 30 is defined as upper PCA is active, the lower PCA is not communicating
You most likely have a bad lower Motherboard, need to send it in for repair or replace it. (you can buy it from Ebay for around 125$ it called a IFT Box Motherboard
Error 22 on treadmill?
Error 22 motor pulses incorrect. Dust on the speed sensor, vacuum out the drive motor compartment. Air out use compressed air.
Error 42, precor 932i?
Error 42 is a lift motor going bad or has failed
@@coloradocardioI can calibrate the motor on the machine, because I already checked the motor and it's fine, I just put it in the machine and I get error 42
Hello. Error code 15 please and thank you
When the treadmill is used by a vigorous exerciser walking or running at
steep incline or when pushing against the handlebars while the belt is moving, the AC motor becomes a generator
forcing power back into the Motor Controller. This excess power would cause the bus voltage to increase enough
to damage the control module were it not for the DB (dynamic brake) resistor, which automatically switches on to
absorb the excess power. Error 15 is an indication that the Bus Voltage exceeded the bus voltage limits, either
because the DB system wasn’t functional or because the bus voltage power exceeded the DB system limit.
a. If one time event, clear the error log and return to service.
b. If repeated occurrences of the error are shown, clear the error log, raise the elevation to 15%, and
walk at a fast but comfortable pace, pushing slightly against the handrail. If you are able to easily
generate an Error 15, replace the DB resistor.
Silicone the underside of the running belt so you don't have any friction between the belt and the running deck. If the error is still there you have to replace the DB Resistor.
Erroe 15 and erroe 82
Error code 30 on eliptical
Error 30 is a communication error from the lower motherboard to the upper board. Check to make sure those connections are secure. If problem still there, you will have to send in the IFT box in for repair approx $250
If you have plz reply
Code 80 on a precor tread mill
Precor Error Code 27
Error 27 is triggered when the motor current increases to the maximum drive motor current.
Silicone the underside of the belt. Or your motherboard will need to be replaced.
Error code 22 and 26
And how do you fix it? I have a 425/445 treadmill
Drive motor problem, check speed sensor.
Might need to send in the motor to gympart.com