Ah I wish I would have installed this on my new vsett10+ 3 days after I got this Amazing scooter I took one hand of my handlebar to adjust the light at maybe 15mph or less And I totally had an encounter with the ground thanks to the wobble I have injured ankle, and badly scrape knees and elbows….
Thanks for the guide - was very helpful in figuring out where things went. My head bolt was super tight (both original and replacement), and it took a lot of effort & rubber mallet banging with the 10mm hex wrench to line up the side screw holes vertically. Glad it's done.
You may notice a lot of noise being made with the shock flopping up and down while riding. As an FYI, I made a few rubber washers and inserted them between the shock and the steering damper mount. They really help to make the damper quieter. Check out my UIanzi Mount #2 video if you want to see how it looks and sounds. Hope that helps some folks out! Thanks for posting this video, and wish you had it up before I installed my setup.
Did watch your video but didn't see where you made this modification. Maybe you could make a short video and point it out. Was listening for comments but only heard road noise.
Ordered mine, coming in 2 weeks. DEFINITELY NEEDED AT HIGHER SPEEDS! - thanks for this install video, looks like a piece of cake! Looking forward to experiencing the difference. 👊😎
I test drive my Brother's Vsett10+ in our street, set to speed 2. I max the throttle as soon i'm in the middle of the street. Smooth and fast acceleration when goes to 0 to 21 mph, then it will kick again on 21 mph up to 43 mph still going on but, i have to slow down on 43 mph cuz the handle bar starts to wobble a little bit from there i got scared and slowed down. Usually 40 mph that's the maximum speed you usually satisfied in driving fast in the street. Over than 40 mph you need a dampener to steady the handle bar on this Scooter.. This is just my opinion...My brother gave me his Hiboy s2 pro scooter 18mph max :( .. But still appreciated :) Thanks for the review :)
It make more sense for the black spacer for the rear hole supposed to be on the inside...not on the outside like you did.🤦♂...better movements because there's a SPACE(R) 🙄between the 2 solid pieces (less stiffness and stress on the rod), and to prevent the 2 metal parts from rubbing...the spacer also is beveled on one side...the correct way is facing out...so that the flat side rest flat on the inside piece and the beveled side kinda blend into the hole of the outside piece. The way you have it...it prevent the silver flexing ring from flexing to its fullest potential...full tilt looks painful as the 2 metal pieces are closer than they should be...stressing on the rod over times...also potentially rub/scratch.
Note** It would be advisable to remove the two (2) screws under the damper bracket, apply red loctite and screw back in before installing permanently. If not, those two screws will loosen over time.
What bothers me is that the original side setscrews(2) are much LONGER than the cap screws you are replacing them with...almost like those screws don't really do what they were designed to do after this installation. ALSO shouldn't there be a specific torque spec for the long main bolt?
What's the difference between the long and the short one? (Sorry, haven't finished the whole video yet in case it is mentioned) - edit: Nevermind! Thanks so much for the video
Set screws are almost impossible to remove on my scooter. Heated it with a hair dryer and it doesn’t want to budge!! Also 10mm wrench won’t go into the head bolt! So far this install has been a disaster!!!! Your example is straight forward but it looks as though your bolts and screws were much looser! Not sure at this point what to do 😐
Hi there. Where could I buy the whole kit? Including the steering damping + the mounting or base kit?. In Amazon, I've only found the steering damper. I appreciate your response. Regards. Juan
Don't buy from EVO. They've been screwing up orders because they don't have any more Vsett 10+ kits. They'll charge you $225 then send you a different brand part (Falcon) for the wrong scooter (Vsett 9). Their website even shows the Vsett 9 and 10 dampers as the same part. They'll blame YOU and say you ordered the wrong part. AVOID LIKE THE PLAGUE.
Don't buy from EVO. They've been screwing up orders because they don't have any more Vsett 10+ kits. They'll charge you $225 then send you a different brand part (Falcon) for the wrong scooter (Vsett 9). Their website even shows the Vsett 9 and 10 dampers as the same part. They'll blame YOU and say you ordered the wrong part. AVOID LIKE THE PLAGUE.
Ah I wish I would have installed this on my new vsett10+ 3 days after I got this Amazing scooter I took one hand of my handlebar to adjust the light at maybe 15mph or less And I totally had an encounter with the ground thanks to the wobble I have injured ankle, and badly scrape knees and elbows….
Thanks for the guide - was very helpful in figuring out where things went. My head bolt was super tight (both original and replacement), and it took a lot of effort & rubber mallet banging with the 10mm hex wrench to line up the side screw holes vertically. Glad it's done.
My God… FINALLY DID IT!
Had to drill out the set screws to get the main head bolt out!!!
What a celebration afterwards 🍻
You may notice a lot of noise being made with the shock flopping up and down while riding. As an FYI, I made a few rubber washers and inserted them between the shock and the steering damper mount. They really help to make the damper quieter. Check out my UIanzi Mount #2 video if you want to see how it looks and sounds. Hope that helps some folks out! Thanks for posting this video, and wish you had it up before I installed my setup.
Did watch your video but didn't see where you made this modification. Maybe you could make a short video and point it out. Was listening for comments but only heard road noise.
@@MeadeLX50 will make a video to show where it goes, and let you know when it's uploaded
Here's the video showing the mod: ruclips.net/video/mzsMBYhYZpE/видео.html
Ordered mine, coming in 2 weeks. DEFINITELY NEEDED AT HIGHER SPEEDS!
- thanks for this install video, looks like a piece of cake!
Looking forward to experiencing the difference. 👊😎
Did YOU get your order????
Very nice video - explainations are very clear
I test drive my Brother's Vsett10+ in our street, set to speed 2. I max the throttle as soon i'm in the middle of the street. Smooth and fast acceleration when goes to 0 to 21 mph, then it will kick again on 21 mph up to 43 mph still going on but, i have to slow down on 43 mph cuz the handle bar starts to wobble a little bit from there i got scared and slowed down. Usually 40 mph that's the maximum speed you usually satisfied in driving fast in the street. Over than 40 mph you need a dampener to steady the handle bar on this Scooter.. This is just my opinion...My brother gave me his Hiboy s2 pro scooter 18mph max :( .. But still appreciated :) Thanks for the review :)
I have hot 21 with hiboy s2 pro. Really not a bad scooter. Waiting for vsett to come on 🔥
It make more sense for the black spacer for the rear hole supposed to be on the inside...not on the outside like you did.🤦♂...better movements because there's a SPACE(R) 🙄between the 2 solid pieces (less stiffness and stress on the rod), and to prevent the 2 metal parts from rubbing...the spacer also is beveled on one side...the correct way is facing out...so that the flat side rest flat on the inside piece and the beveled side kinda blend into the hole of the outside piece.
The way you have it...it prevent the silver flexing ring from flexing to its fullest potential...full tilt looks painful as the 2 metal pieces are closer than they should be...stressing on the rod over times...also potentially rub/scratch.
Note** It would be advisable to remove the two (2) screws under the damper bracket, apply red loctite and screw back in before installing permanently.
If not, those two screws will loosen over time.
Mine fell out. Ended up using two different little bolts with blue lock tight cause I lost the originals
Glad you found a solution!
4:23 Where did you order that 10mm tool on your right hand?? I can’t find it
Where to buy this kind of steering damper ,link please
What bothers me is that the original side setscrews(2) are much LONGER than the cap screws you are replacing them with...almost like those screws don't really do what they were designed to do after this installation. ALSO shouldn't there be a specific torque spec for the long main bolt?
They're called grub screws and you're absolutely right that the short bolts they use to replace them with are an serious accident waiting to happen.
Those 2.5mm Allen key screws are bloody tight. .
This. They were a nightmare
What's the difference between the long and the short one? (Sorry, haven't finished the whole video yet in case it is mentioned) - edit: Nevermind! Thanks so much for the video
Set screws are almost impossible to remove on my scooter. Heated it with a hair dryer and it doesn’t want to budge!!
Also 10mm wrench won’t go into the head bolt!
So far this install has been a disaster!!!!
Your example is straight forward but it looks as though your bolts and screws were much looser!
Not sure at this point what to do 😐
Maybe we can help if you reach out to us with a ticket! urbanmachina.freshdesk.com/support/tickets/new
When are you getting this back in stock?
It's on ATM for 1499
red loctite? good luck when u need to unscrew the bolt
Imagine driving into someones leg :o
Hi there. Where could I buy the whole kit? Including the steering damping + the mounting or base kit?. In Amazon, I've only found the steering damper. I appreciate your response. Regards. Juan
Hi Juan, we'll be restocking the whole kit closer to June. Be sure to check back then!
@@UrbanMachina Thank you for your prompt response. Regards. Juan
Don't buy from EVO.
They've been screwing up orders because they don't have any more Vsett 10+ kits.
They'll charge you $225 then send you a different brand part (Falcon) for the wrong scooter (Vsett 9). Their website even shows the Vsett 9 and 10 dampers as the same part. They'll blame YOU and say you ordered the wrong part.
AVOID LIKE THE PLAGUE.
I literally couldn't get that front bolt out on the stem and the fucking bit broke off in the set screw as I was trying to get it out.
Para que funciona ?
For rider safety. To prevent / control front wheel wobble at higher speeds.
Damper muy afuera
send link damper sir tq
Of course! It's in the video description.
Use a Gas Drawer Damper Cheap and more stable!!!
The audio on your videos isnt the best. Love the videos on the 10+
The thing is hitiing
That looks dangerous in the uk you would get nicked for having a lethal weapon
Don't buy from EVO.
They've been screwing up orders because they don't have any more Vsett 10+ kits.
They'll charge you $225 then send you a different brand part (Falcon) for the wrong scooter (Vsett 9). Their website even shows the Vsett 9 and 10 dampers as the same part. They'll blame YOU and say you ordered the wrong part.
AVOID LIKE THE PLAGUE.
Or you can buy from us if you're located in the US or CAN. 💪🏼