THIS is exactly the video I needed. Thank you! I have the 2023 vsett 10 + but the settings seem to be identical. I just don’t know why the unused settings are there in the first place
@@GiRideswhat exactly is the purpose of regen braking? I turned that off because I felt it braked too hard and fast and was afraid of going over the bars
Keep if OFF, already replaced one controller using regen. People using it to save brake pads and getting a couple % back to the battery. Just don’t use it if you have vsett 10+
@@bacopaolo1 you have to hold the finger throttle at the same pressure and maintain the speed you want for 8-15 seconds, then let off and it should kick in. if not, you didn't wait long enough. (make sure you stay at same pace for 8-15 seconds). Tapping the brakes will disengage the cruise control, as well has hitting the throttle.
P1 screen brightness P2 Mile to kilometer P3 voltage P4 Amount of min until scooter turn off P5 unused P6 wheel diameter P7 magnet in motor P8 Power limit P9 kick start 1 on 0 off P10 unused P11 regen brake P12 Acceleration P13 unsused P14 unused P15 volts until scooter turn off P16 reset miles P17 cruise control P18 bind unbind nfc card P19 unused P20 unused
Hello. I am thinking of upgrading my Vsett 9 Plus battery to a 52v ,like the Vesett 9.By doing so, I will also change my P Setting to 52. Do you think Vsett 9 Plus might get more mileage? Thank you so much for this video. Very helpful!
It’s weird cause the stock screen I could ride 20 kms and still have 54 volts now with the new screen I ride the same now it’s saying 52 volts lol are the upgraded ones more accurate or something
Hi, i have a question in some e-bikes or scooters order to change p settings you need to enter a password first where is this password is stored ? in the display throttle or inside the controller i mean if i have my p-settings locked and i will replace the display (qs-s4) will it help or the password stored inside the controller TIA
Hello! i wanted to ask for your opinion! i am getting in future Vsett 10+ but mine will come with limited speed max 25 kmh i am planning to cut the white cable, but is it ok if i manipulate with P8 in case i want to bring it on 25 kmh lets say if i lower from P8-100 to P8-21 then will make it 25 kmh i saw one vid in RUclips the same did and it worked, my question is for a man who has about 96 kg would it work if i go uphill exact 25kmh or will move like turtle :) i would like if you try and test uphill this with your scoter and let me know. Thanks.
67.2 volts maximum charge on my Vsett 10+ when it's rated at 60v.... ? Strange but i get extra mileage out of the higher charge. Is this normal for all scooters?
Guys, my LCD screen broke. Can anyone tell me what the default voltage setting the LCD screen comes with? And whats the highest it goes to? So i can set it without looking at the LCD. Thanks
That means there is an error. It probably means the breaks are always being pulled so hey need to be loosened some or maybe tightened, try both by twisting the screw by where the break cable ends next to both wheels
What happens if you change the unused P Codes? Also the Manuel says that P20 is not unused but it’s actually the “Communication Protocol” and that it is set to 4 and cannot change. What does this mean? What happened if you change P20? Will it break my scooter? They should have just hid all of the unused codes and P20 and all of the ones that shouldn’t be changed like the wheel diameter, magnets number, and the voltage level since those are specific to each scooter and should not be changed, also there should be a better screen that is able to explain what each setting means in case you don’t have the Manuel. I know I could just design the perfect electric scooter that would be easy to understand. If you paying $1,000-$4,000 for a scooter, it should have a real screen and not a calculator screen to be honest. Like think about what are we supposed to do if you Manuel gets lost like mine almost did???
Hey great video it worked for me on my vsett 8 Boss Scooter bro getting 26 mph on it full out can I get more out of it.? 🙄 Please let me know keep the grate work bro
I yust broke code and my Scooter when I turn him on he yust opens upp and I must reset all and all 3 cards put od rsd holder:)) . Only I ride VSETT8 and it had 48V battery so I haw put 48 where yours is 60V and magnets doo I also put 30 number off magnets and only one thing you set yours too 100km/h mine goes 45 so mu I leave it there or not. Sory for long message. But those tings I'm not 100%shure
@@GiRides its cool bro thnkyou,, by the way about the psettings that you are using rightnow is that recommended ? Hehe i only hsve vsett10+ 20.8 ah thats the available here on ny location
@@GiRidesnd another (i just find y the perfect person to ask) on a little sticker on vsett 8 i think it says that u should fully charge the scooter before the first use is there a problem If i didn't?*
@Gi Rides thank you please i pay vsett8 and if you can tel me how I repre settings I prepr that , p3, 36 and p6,90,and p7,28, and p5 , 290 if that good or not please tel me thank you very much
Развлечения
Thanks mate I just put the upgraded screen on my vsett 11+ and all my p setting rest lol so was really helpful
Your're a savior!! Vsett 8 owner here.
Vsett 8+?
Whats your settings looking like?
hey dude, me too😀, can you tell me if you've ridden it in wet conditions(not rain but wet tarmac), and how does it hold up?
Danke fur diesen super vortrag hat mir sehr geholfen
Thanks man I appreciate this!
Thank you for this video:) I am getting the vsett 8! liked and subsribed
Thank you❤️❤️
I have a vsett 8 and i am telling you , is best thing you could have . I rode it to work for abot 3 months . Now is in storage due to cold weather
@@mariusandrei4568 It has great built quality just acceleration could be a little better, I like zero9 a lot more
@mariusandrei4568 so no drive at all during wet conditions?
Thank you man!
Thanks you help mee alott.
👍 Thank you very much!
very helpful, thankyou
THIS is exactly the video I needed. Thank you! I have the 2023 vsett 10 + but the settings seem to be identical. I just don’t know why the unused settings are there in the first place
Glad it worked out for you!
@@GiRideswhat exactly is the purpose of regen braking? I turned that off because I felt it braked too hard and fast and was afraid of going over the bars
Keep if OFF, already replaced one controller using regen. People using it to save brake pads and getting a couple % back to the battery. Just don’t use it if you have vsett 10+
@@GiRidesso it overheated the controller?
@@scottg429 yes
thanks man!
Cruise control is causing me problems on my first day thank you worth the wait till the end
Go to P17 and change the value from 1 to 0
how cruise control works?
@@bacopaolo1 you have to hold the finger throttle at the same pressure and maintain the speed you want for 8-15 seconds, then let off and it should kick in. if not, you didn't wait long enough. (make sure you stay at same pace for 8-15 seconds). Tapping the brakes will disengage the cruise control, as well has hitting the throttle.
Thanks for this video 👍💯
You are welcome
P1 screen brightness
P2 Mile to kilometer
P3 voltage
P4 Amount of min until scooter turn off
P5 unused
P6 wheel diameter
P7 magnet in motor
P8 Power limit
P9 kick start 1 on 0 off
P10 unused
P11 regen brake
P12 Acceleration
P13 unsused
P14 unused
P15 volts until scooter turn off
P16 reset miles
P17 cruise control
P18 bind unbind nfc card
P19 unused
P20 unused
What happens if you change the unused codes?
Hello. I am thinking of upgrading my Vsett 9 Plus battery to a 52v ,like the Vesett 9.By doing so, I will also change my P Setting to 52. Do you think Vsett 9 Plus might get more mileage? Thank you so much for this video. Very helpful!
I can’t answer to this question but i think you need bigger ah battery which gives you more range because Voltage only gives you more power
The odometer can be clocked just with holding one button? That seems crazy
It’s weird cause the stock screen I could ride 20 kms and still have 54 volts now with the new screen I ride the same now it’s saying 52 volts lol are the upgraded ones more accurate or something
What do you think is the problem is the "on" button is hard to press but it's clicking?
Hi, i have a question
in some e-bikes or scooters order to change p settings you need to enter a password first
where is this password is stored ? in the display throttle or inside the controller
i mean if i have my p-settings locked and i will replace the display (qs-s4) will it help or the password stored inside the controller
TIA
Try 1500
Hi Please help me, the tail lights are still on, romobil don't want to start, what is the problem?
Hello! i wanted to ask for your opinion! i am getting in future Vsett 10+ but mine will come with limited speed max 25 kmh i am planning to cut the white cable, but is it ok if i manipulate with P8 in case i want to bring it on 25 kmh lets say if i lower from P8-100 to P8-21 then will make it 25 kmh i saw one vid in RUclips the same did and it worked, my question is for a man who has about 96 kg would it work if i go uphill exact 25kmh or will move like turtle :) i would like if you try and test uphill this with your scoter and let me know. Thanks.
I would like to test it for you but we have 1 foot snow outside right now:) When it heats up a little I will do this test for sure!
Please don't cut. There are connectors inside the deck.
Why my vsett 10 doesnt go below 58 voltage even with full charge ( green light)?
67.2 volts maximum charge on my Vsett 10+ when it's rated at 60v.... ?
Strange but i get extra mileage out of the higher charge.
Is this normal for all scooters?
Yes, this how it must to be 67.2 is 100% charged 60v battery
Guys, my LCD screen broke. Can anyone tell me what the default voltage setting the LCD screen comes with? And whats the highest it goes to? So i can set it without looking at the LCD.
Thanks
Do you know how do I flash the front lights in VSETT 9+ Scooter?
Not sure if you can, could be wrong.
I'm trying to find out what the cut off voltage should be for vsett 9+ if any knows??
Thanks
how can i find charging indicator vsett 10+
but my p settings is upto 9 only is it different?
May I know how to remove the exclamation mark on my screen? It always show even I don’t touch anything
Yes, just snap the brake levers and after that you have to losen the brake sensor screw, very easy fix
That means there is an error. It probably means the breaks are always being pulled so hey need to be loosened some or maybe tightened, try both by twisting the screw by where the break cable ends next to both wheels
What happens if you change the unused P Codes? Also the Manuel says that P20 is not unused but it’s actually the “Communication Protocol” and that it is set to 4 and cannot change. What does this mean? What happened if you change P20? Will it break my scooter? They should have just hid all of the unused codes and P20 and all of the ones that shouldn’t be changed like the wheel diameter, magnets number, and the voltage level since those are specific to each scooter and should not be changed, also there should be a better screen that is able to explain what each setting means in case you don’t have the Manuel. I know I could just design the perfect electric scooter that would be easy to understand. If you paying $1,000-$4,000 for a scooter, it should have a real screen and not a calculator screen to be honest. Like think about what are we supposed to do if you Manuel gets lost like mine almost did???
How did you get the number of magnets for setting P07? Is it the same for all Vsett models?
I believe that 10 and 11 has 30 magnets but 8 and 9 has 28 magnets, correct me if I am wrong
The Manuel says that the default is 28, set it to 28 if you don’t know what it should be on
how can it be adjusted when starting the scooter to be in 3 gear
There is no way to do that
@@GiRides thank you very much for your reply❤️
Hey great video it worked for me on my vsett 8 Boss Scooter bro getting 26 mph on it full out can I get more out of it.? 🙄 Please let me know keep the grate work bro
No, you can’t get more out of vsett 8
@@GiRides thanks for coming back I'm happy 😊
I can not unlock the on-board computer after nfc settings. What to do?
Please explain what you mean? I’ll help
I yust broke code and my Scooter when I turn him on he yust opens upp and I must reset all and all 3 cards put od rsd holder:)) . Only I ride VSETT8 and it had 48V battery so I haw put 48 where yours is 60V and magnets doo I also put 30 number off magnets and only one thing you set yours too 100km/h mine goes 45 so mu I leave it there or not. Sory for long message. But those tings I'm not 100%shure
good explanation, it's tedious to read the manual, not all too well translated it is.
It’s translated really bad but not as bad as the manual for this hoverboard that I used to have
why it doesnt show p8?
I'm going to try the settings on the wheel. it reads 4 mph too fast. based off of GPS
It will correct speed if you use my settings on vsett 10
@@GiRides after I made the changes, it now reads correct. with the stock settings you would believe to hit 50 mph on sport mode.
@@DrWonderEyes Yes, they made it very inaccurate from the factory. And they lied saying that it goes 50 MPH even though it doesn’t.
Does the same apply for vsett 11+ ? Im getting mine tomorrow.. and also what app do u use for gps readings? Thanks
@@tomzi9526 yes the same except tire size, the app i use for gps speed called "Speedometer" on ios
Can you reset your miles more than once as I’m having trouble doing it
Is all of this listed in a book?
I don’t have a book so not sure about it
Yes, it’s in page 18 of the Manuel that came with my Vsett 8+
How to fix when error and my hub not working too
You just have to google for error codes and go from there
@@GiRides thank you error code is 00 and 09 im worry about 09 its controller 😔😢
In your psettings bro,, its worth it? 4days ago i got my scooter vsett10+
Great scooter, how do you like it?
@@GiRides its cool bro thnkyou,, by the way about the psettings that you are using rightnow is that recommended ? Hehe i only hsve vsett10+ 20.8 ah thats the available here on ny location
@@myk2139 yes what i use in the video i can recommend for 10+
@@GiRides ohh tnx for helping me on this Psettings.i hope it will work till my vsett10+ getting old. Hahahah ✌️
@@GiRides hi bro,, on this Psettings how many years you are using this and until now your vsett10+ never got issue til now and it still powerful?
What is kickstart and whats the point to have it?
Safety, kick before you start riding
Is it also safe for the engine and battery?
@@aptioskanov5762 yes, uses less battery
Last question. How do I see how much electrisity i have left in my battery by numbers?
@@aptioskanov5762 just read volts on the display, and google for volts/% chart
tip - dont mess with the wheel dimensions regardless if you think its making your scooter faster it honestly doesnt
good vid tho mate
It makes mph readings more accurate:)
yeah the v10 comes showing FASTER from the factory, he slowed it down...
How many magnest vsett 8 has?
I guess 28 but not sure
@@GiRideswow Man ,u'r name should be flash
@@GiRidesanother question ,what cells the battery have?
@@infinit280 lowest capacity battery has generic china cells, the other 2 higher battery options has LG cells
@@GiRidesnd another (i just find y the perfect person to ask) on a little sticker on vsett 8 i think it says that u should fully charge the scooter before the first use is there a problem If i didn't?*
Hi please that four vestt8 olso
Yes
@Gi Rides thank you please i pay vsett8 and if you can tel me how I repre settings I prepr that , p3, 36 and p6,90,and p7,28, and p5 , 290 if that good or not please tel me thank you very much
@@hamzalayouni574 P3-48, P5-000
My scooter is stuck at going 15 mph when I want to go 20+ any ideas?
Change gear maybe from 1 to 2 or to 3 :)
@@GiRides unfortunately gear 3 is 15 mph
cut/unplug white cable under deck
@@milordas on the wire harness, look for white wire. cut and separate (its a looped wire)
Yeah it may have a speed limiter connected under the hood, look up speed limiter removal on RUclips.
I lost alot of acceleration power
Why? How?
@@GiRides my vsett 10 plus barely has the speed now , idk