【加工動画40】回転センター研削/How to grind a live center
HTML-код
- Опубликовано: 29 дек 2022
- 中古の回転センターを研削しました。
安全に配慮してアイデアの種にしていただけたら幸いです。
ダイヤモンドホイール(#150):amzn.to/3Vh7jmE
(#1000):amzn.to/3BXaPvK
コードレスドライバドリル:amzn.to/3F1JASU
クイックバークランプ(大):amzn.to/3U3TYO6
(小):amzn.to/3gR8ue8
熱可塑性ポリウレタンベルトφ4×1m:amzn.to/3VSMDCP
半田ごて:amzn.to/3sG3Wtn
ダイヤルゲージ(0.001mm):amzn.to/3jvPG59
ドレッシングストーン:amzn.to/3Voxgk0
快段目盛15cmスケール(定規):amzn.to/3EoY8L0
撮影機材:amzn.to/3bNBj5D
使用した旋盤/Lathe model: ワシノ/Wasino LR-55A
背景音楽/BGM: New Land - ALBIS
We would appreciate it if you could use it as a seed for your ideas after considering safety. - Наука
素晴らしいチュートリアルです! 共有していただきありがとうございます!
回転センターを研削することがないので見てて勉強になりました。
Thankyou for the excellent videos you produce! From Australia
勤務外でこういうことしたいですね。本業リーマンでは時間の確保が難しい…試したいこと山ほどあるんですが。
Very clever! great idea using tailstock quill.. Thanks for sharing!
Beautiful surface finish
Erasing those battle scars looks incredibly satisfying
As always thank you for uploading a great video
Great Master. Very beautiful and precise work, a person gets the joy of looking at this work
Happy New year Swanp lamp ,i look forward to more of your exellent teaching in the new year
Great job as always and very neat 😜
Completely accurate and perfect 😉 work 👍 👋💯 bravo ☺️
Ottimo lavoro! Buon nuovo anno.
ты просто молодец спасибо тебе , у меня сразу появилась мысль попробую заточить на токарном так же резцы для токарного, спасибо ещё раз удачи тебе и привет из Беларуси
To catch the grinding debris and prevent damage y to o my lathe I use squares of old carpet with a layer of grease spread on it. It catches and keeps everything with no bouncing off. Super cheap and super effective!
Show congratulações pelo vídeo
great solution thanks.
This isn't terrible. But if you do this with the live center place in location to where it will be and grind it there, it will match the runout of the spindle. You can put a grind wheel on an arbor in the jaws side. Then a diamond in the tool holder. Dress the correct angle in the wheel. Then you just do a plunge into the live center being spun by the drill. You will then have the perfect angle and runout matched to your jaws.
Excelent job, congratulations
Excellent job, 👍👍👍
A very clever job !!!
좋은 결과물을 만들기 위해서는 끊임없는 교정이 필요한 거였군요. 👍🏻👍🏻👍🏻
Great stuff. Thanks
You have one heck of a precise lathe! You can also use dry plumbers silicone to clean diamond wheel or sandpaper.
I've used an old rubber shoe before, both are excellent
The workshop cleaner than a hospital operating theatre,,!,,,,!!,,,
ビト砥石をご使用の場合、乾湿両用以外では水や油等で濡らさない方が長持ちします。濡らしてしまうと劣化を早めてしまいますので。
レジ砥石の場合は濡らしてご使用下さい。
又、ドレッサーをご使用の場合、GC F180砥粒と併用致しますと長持ちし易くなります。
Excellent jobb !
Абразив - это именно то, чего так не хватает станку. Никаким способами не избежать попадания абразива в чувствительные места станка. Для каждой операции должен быть свой станок.
excelente trabajo
nice work
Better than factory!
どうやって刃物台に固定擦るのかな~と思ってたら芯押し台のスリーブ( あってる?)ごと固定するとは目から鱗でした!
やっぱり、そこが一番気になりましたよね!
スワップランプさんの発想力には毎度驚かされます(笑)
Top-Job, Sir👌
それを行う独創的な方法。
あなたは、あなたが作ったスチールホルダーのクランプ法から本当に恩恵を受けます。
私はあなたのビデオを見るのが好きです。
また、あなたがあなたの仕事をするケアを見るのが大好きです。
デンマークからの挨拶。
_Kay _Løwén
great job bro
영상 잘보고있어요 👍
CBN for the win!💪🏻
My live center looks like it was used to split rocks
Gracias por enseñar maestro!!!!
명작업 완료 되었습니다 감사합니다 선생님
Браво 👏👏👍
Tak to świetna metoda . Ja tak równałem kiełki obrotowe już w 1977 roku , tylko że szlifierkach wałkówkach , tak wyrównany kiełek jest sto procentowym zamiennikiem kiełka stałego . Na pasek napędowy naciąłem sobie pół okrągły rowek na kiełku . Ale to wszystko jak kto może , system ten sam . Koledzy temu nie wierzyli , ale jak pokazałem im na czujniku odczyt , który był tak samo na zero , to miny im posmutniały . Tak samo co więksi sceptycy przestali się śmiać . Natomiast to , czy kąt 60 stopni , na maszynie 30 , czy nieznaczna odchyłka kąta , to dla techniki już bez większego znaczenia . Zupełnie już o tym zapomniałem , ale wspomnienia wróciły momentalnie . Natomiast sposób montażu sprytny , przyznaję . Najważniejszy i tak sam system szlifowania . Pozdrawiam .
Good job bro. Video 👍Background song 👍Work👍
Very enjoyable watching a real machinist who knows what he's doing and also who takes care of his machines. It makes a great change from watching the usual You Tube clowns who weld in the lathe. Thank you.
Wonderful
Perfect isn't enough for you bro👍😉
Excelente !!!!
Q limpieza para trabajar saludos desde guadalajara 🎉
Великолепно! )
Хорошо придумал ! Молодец!
Super
Salutari din România
The lathe center can also be put into the work spindle and overturned with a turning knife with carbide. If you have a movable lathe center, you only need to tape the rotating part.
Ну вот и получился новый инструмент! 🤟
Nicely done! I'd try to use a CBN wheel rather than diamond. Diamond has an affinity for steel and will wear faster. But in this case you got away with it.
Funny thing is that You can get away with using cheap diamond wheels on tool steel quite well. Just need to redress them more often, that is use something to abrade binder to expose new grains. I think it works best at fairly low rpm:s. CBN is of course better but expensive.
Es perfecta la idea me gustaría saber a qué r.p .m gira el torno gracias un saludo de la CD. De México
👌
ну что называется, похвастался инструментом) завидую. лайк
Genus!
Grinding cut was not passed till last end.
That's why dial gauge was showing higher reading at the last same thing I do with my surface grinders for many of my item's I make for my tool room....
Die Spitze wird wärmer als der untere Teil, da kommt die Toleranz her.
Maintenance to obtain the movement required for crafting. It's a benchmark for me.
Many tools are made in Japan, but what is KITAGAWA good for? happy new year from japan. ♬
Thank you for watching.
Happy new year.
I have only used chucks made by Kitagawa, Kobayashi and China, so I cannot make a professional comparison with other companies.
Chucks made by Kitagawa and Kobayashi have no problem in normal use.
No fatal problems occurred even after long-term use.
Kitagawa's general size chuck body is not made of cast iron, and the maximum allowable rotation speed is about 50% higher than that of cast iron, making it highly durable. The price is also high.
Супер!!! 👍👍👍
👍🏻
Tremendous
Better than factory results.
Наконец микронный индикатор. Таки добился точности как у Анатолия Сандимирова
Если постараться можно сделать лучше, придется переделывать 😊
عمل جيد
работает на станке, а пальцы чище женских после маникюра! Каааааак, как такое возможно, задев любую ручку пальцы уже должны испачкаться!
أللهم صلى وسلم وبارك على نبينا وحبيبنا محمد صلى الله عليه وسلم
Pytanie czy nie zbierasz szlifowaniem utwardzonej powierzchni i ile taka regeneracja wytrzyma.
Gönderene teşekkürler deniycem
This is kinda stipid cause the jaws will always grab something with some amount of error introduced
Shield clogged? Where is the cooling?
boaboaboaboaboa
😍😍😍😍
Красивая работа! Абразив на точном станке, сомнительно
L’excellence a son paroxysme !!!
砥石のドレスやってから加工に移らなくても案外やれちゃうモノなんでしょうか?
あとダイヤルゲージで1umの読みを求めるのはやらない方がいいと思います。
保証精度の点からして指示誤差とか大きいですので。
たぶんリニアゲージ使った方が精度良いと思いますが、如何でしょうか?
日本が第二次世界大戦敗北の理由が良くわかった。
Tôi mãi xong mấy cái rồi vẫn đồng tâm 0,01.
精度がキッチリ出てる旋盤で無いと
こういう事はできないですね。
Why do much work, just disassemble the live center and grind the heart, which is almost identical to dead center.
Place dead center in check, spin at 1000 rpm a d grind with a tool post grinder.
You have a valid point, if the bearings are at all worn in the live centre then the finish and the accuracy will be compromised.
Personally i thought that the final ground finish should have been a bit better but the dial indicator gauge at least showed it to be running true.
why put a nylon washer ?
Thank you for watching.
The wheel is made of aluminum, so if you tighten the nut directly, the surface will be rough.
Also, I think that MC nylon can apply surface pressure more evenly between the arbor and the wheel than using iron washers.
Хтось би то сумнівався 👍. Фахівець! 😇
What is the orange rubber band called?
Thank you for watching.
Although it is an orange cord, the product name is called Bancord or Bancord round belt.
The model number for this product is NO480-4-C1000.
あと0.04傾ければ完璧ということですか?
ご視聴いただきありがとうございます。
このダイヤルゲージは1目盛りあたり1µm(0.001mm)なので0.004mmのズレが生じてしまいました。
これは目詰まりと直径を考慮せずに自動送りで仕上げたため、太い部分の研削が浅くなってしまったためです。
おっしゃるように傾きで調整するか、微細な仕上げ研削を繰り返せばよりズレの少ない仕上がりになると思います。
thank you.
and BGM name? please
Thank you for watching.
BGM is New Land - ALBIS.
Хороший получился конус😁👍
CBN?
Jesus Christ! Those tolerances kill me
линейку приложил в конце видео для чего? она ж не лекальная
Спасибо за просмотр.
Особого смысла нет, но я подумал, что размер, отражение зеркальной поверхности, прямые линии можно было увидеть интуитивно.
Arigato sensei!
Is that a 60 degree live center ?
Thank you for watching.
That's right. 60 degree live center.
回転センターの研磨は予想ついたけど
インパクトとゴムチューブの用途が解らない………
Лайк. Но на шурике есть реверс.
Такая схема ремённой передачи применена, вероятно, для увеличения угла охвата шкива и конуса и как следствие исключение "пробуксовки"оных.
It’s ok to use diamond wheel on high speed steel live center? I thought diamond should only be used on carbide?
Thank you for watching.
CBN was expensive so I used very cheap diamond wheels made in China.
On Amazon Japan, #150 was $11 and #1000 was $20.
The thermochemical reaction in which diamond diffuses into iron does not occur below 700°C.
The spindle of this lathe was 275 revolutions per minute, and the amount of grinding was less than 0.01 mm, so the diffusion of the diamond was not felt.
@@SwaplampJapan 👍 you make great videos
Две мигутэс латэр как это понять?
Спасибо за просмотр.
Две минуты спустя.120 секунд спустя.
@@SwaplampJapan ну не всё могут это почитать
@@kurtler1 Спасибо за ваш отзыв.
Я думал, что английский будет относительно легко перевести. Если вы увеличите количество отображаемых символов, их будет трудно увидеть из-за пробела, поэтому, пожалуйста, простите меня за неудобства в будущем.
@@SwaplampJapan для нас английский по сложности ни чем не отличается от японского и китайского. Нам на русском надо
станок конечно вылизал, чисто для видео так сделал?
3:50 кто такая дуст Копер?
Спасибо за просмотр.
суперобложка. Это средство для удаления пыли.
Цель - предотвратить попадание абразивов в швы.
🙂👍👏🇺🇦🌲
The grinding wheel isn't flat, and should probably be dressed so it is.
Шляпа какая-то. Что конус в патрон нельзя было зажать и проточить? Опосля полирнуть.
Данный метод восстановления конуса подвижного центра самый точный, так как несоосность конусной поверхности с осью вращения обусловлена классом точности подшипников, в коих вращается конус центра!!!