Where is the fail?? M4s, m16s and ar platforms all do the same thing when you strike the butt stock upon a hard surface while the bolt is locked back to the rear with no magazine inserted. It provides just enough force to relieve the tension on the bolt catch/release which will send the bolt home...I'm assuming this is the same scenario. It's not a malfunction
Not mortaring. Mortaring is for removing a stuck case. BCG has to be forward, and hope the extractor bites enough, so when you slam it, the rearward motion will extract. The BCG acts like a dead blow. If that fails, then lock back to rear, and use cleaning rods. Slamming a BCG forward, like in this clip, will only stick the stuck case even more sticker. That’s not gooder at all.
This isn't a fair. That happens to every ar platform. The bolt carrier group releases some of the pressure it is putting on the bolt catch and so the bolt catch disengages.
There is no fail. The bolt carrier group moves downwards on the principle of inertia due to the impact. In the meantime, the bolt catch is released and returns from the lock position to the normal (unlock) position in this way. As the lock is opened, the bolt carrier group is released and move forward to the barrel. This is the same thing with pulling and releasing the charging handle when there is no magazine.
We had a drill with the m4 we take the butt off rack the handle then hit the buffer tube into the chest/shoulder hard enough so that the bolt releases so yea it hurts but it works.
@@mozhetbahnem Нужно как раз с магазином без патронов пробовать. На АРке становится на задержку так, без магазина не становится, может СИГ тоже так сделали (мол без магазина не критично если что...).
Wo ist denn jetzt hier das Problem? Andere Waffensysteme wie zum Beispiel AR15, M4, M16, M14,....und viele andere mehr haben dieses angebliche "Problem".
Ça ne fonctionne seulement quand il n'y a pas le magasin donc pas de risque mise à part celui de ce coincer le doigt dans la culasse (ce que je déconseille fortement d'essayer)
So does every ar platform...it's the way it's made. When I was a weapons technician, we used to demonstrate this with m4s carbines too....we made it look like a trick.
Where is the fail? The hard rubber butt reduces vibrations and increases accuracy. After all, you can hit any Coke bottle at a distance of 400m even without a scope.
Сильно сомневаюсь что это прямо проблема, подобный прикол был и на паре моделей винтовок фирмы Вальтер . На них вылечили заменой пластикового приклада на металлический. У ЗИГа 550 из видео тоже схожая конструкция в этом отношении.
Спуск курка тоже!?😮 Для чего нужна затворная задержка, вот от этого надо исходить. Если для удобства, обозначить что БП всё то, натурально, такая ситуация притянута за уши))
Yeah, contrary to popular belief they are trash, you are lucky the stock didn't break off... My company alone had 5 broken stocks, about a dozen broken charging handles and a bunch of shattered mags and that's just 100-ish guys.
Maybe the issue here is you? I used it during my service as infantryman and it has seen alot of rough situations. These same guns are used by many different militias and I have not yet encountered anything like you mentionned. And we had like 200 different rifles in use for 14 months straight...
@@mnk9073 Before you make such bold statments maybe you should inform yourself. We get old and used rifles. Do you really think the army is investing every year for 12000 new rifles for each recruit? If a rifle is worn it gets repaired by the gunsmith. If you're lucky, you'll get a rifle with a brand new barrel while the rest is still old like the gas tube, spring and so on. My rifle had markings from rust in the barrel and gas tube due to poor maintenance of the previous owner. The rest was ok. It shot well despite its flaws.
Where is the fail?? M4s, m16s and ar platforms all do the same thing when you strike the butt stock upon a hard surface while the bolt is locked back to the rear with no magazine inserted. It provides just enough force to relieve the tension on the bolt catch/release which will send the bolt home...I'm assuming this is the same scenario. It's not a malfunction
@CavTrooper19Dit's not an open bolt rifle, of course not.
That happens to every ar platform
Thats not ar plastic shit.
Technically seen is the SIG 550 more related to the AK family.
@@railtech1536 i guess he ment assault rifle
It's called mortaring, and now you learned something today
Not mortaring. Mortaring is for removing a stuck case. BCG has to be forward, and hope the extractor bites enough, so when you slam it, the rearward motion will extract. The BCG acts like a dead blow. If that fails, then lock back to rear, and use cleaning rods. Slamming a BCG forward, like in this clip, will only stick the stuck case even more sticker. That’s not gooder at all.
Imagine having access to such a nice rifle and having no knowledge of firearms
Not fail. It s normal
Sig 550's (i think) are so damn cool!
Why did you say anything at all
They sure are amazing rifles.
@@e.t.2230why did you?
More of a feature than a fail imo
Wait till he finds out how much metal shit whips around when you shoot
No fail in there.
Das ist kein fail - es hat sich kein Schuss gelöst- nur der verschluss ist zu - zu 99% bei allen.
😅Boohoo for your troubles - you've got a high quality Swiss rifle right there!😊
Is the fail the bolt bounce? That’s the only thing I can see that is an issue.
happens to ninety-nine percent of ARS you guys stupidity is amazing
And The rest of 1% is because the impact at the bottom is not huge enough.
we always used this effect for reloading
Bro is scared of the word inertia
If you want to demonstrate this 'failure' make sure the chamber is empty unless one wants a bullet wound in the chin!😅😅😊
this is not a fail it is how we load it in the swiss army ..lol lol
This isn't a fair. That happens to every ar platform. The bolt carrier group releases some of the pressure it is putting on the bolt catch and so the bolt catch disengages.
It is because the BCG bounced back because of the impact.
@@blackcatpackYes.
There is no fail. The bolt carrier group moves downwards on the principle of inertia due to the impact. In the meantime, the bolt catch is released and returns from the lock position to the normal (unlock) position in this way. As the lock is opened, the bolt carrier group is released and move forward to the barrel. This is the same thing with pulling and releasing the charging handle when there is no magazine.
Pro Tip: You can even load it that way if you smack it hard enough that is.
No fail, most carbines/rifles do that when you mortar them. Have fun zeroing that scope again.
I really admire the shoe.
💪
We had a drill with the m4 we take the butt off rack the handle then hit the buffer tube into the chest/shoulder hard enough so that the bolt releases so yea it hurts but it works.
Затвор сошел с задержки и попытался дослать патрон в патронник при ударе прикладом о твердую поверхность?
Именно.
@@mozhetbahnem А со вставленным магазином пробовали? Тоже самое?
У нас только боевые патроны, не хотелось проверять.
@@mozhetbahnem Нужно как раз с магазином без патронов пробовать. На АРке становится на задержку так, без магазина не становится, может СИГ тоже так сделали (мол без магазина не критично если что...).
Блин так и у АР слетит от удара . Это фейл только чей ?
Wo ist denn jetzt hier das Problem?
Andere Waffensysteme wie zum Beispiel AR15, M4, M16, M14,....und viele andere mehr haben dieses angebliche "Problem".
It is not problem it is just a physics phenomenon
Hes talking about how ridged the stock. that things bending and not putting a single dent in that wood.lol
😂 now do it with the bolt closed
Ça ne fonctionne seulement quand il n'y a pas le magasin donc pas de risque mise à part celui de ce coincer le doigt dans la culasse (ce que je déconseille fortement d'essayer)
Everybody knows if you hit the buttstock hard to the ground that can happen . 😊
the firing pin doesn’t get hit it only out of battery
I dont get it, fail at what?
Bolt catch disengages if you shake it too strongly
So does every ar platform...it's the way it's made. When I was a weapons technician, we used to demonstrate this with m4s carbines too....we made it look like a trick.
@@mozhetbahnem can you name a weapon system with a bolt hold open that dont do that
@@mozhetbahnemyoure making an issue out of nothing
The Rolex of guns failing … no!
Полное видео будет?
Когда его получим в руки на подольше
Where is the fail? The hard rubber butt reduces vibrations and increases accuracy. After all, you can hit any Coke bottle at a distance of 400m even without a scope.
Any rifle with a BHO and a bolt of any substance will do this
NO MORE SIG EXCUSES
А при срыве будет произведён выстрел? Если да то как этот момент пропустили????
нет, он стреляет с закрытого, ударник подпружинен.
@@geladen а, тогда не вижу особой проблемы этой особенности конструкции.
@@ji9i_9i_kpbica да и нет там проблемы, просто прикол такой.
Сильно сомневаюсь что это прямо проблема, подобный прикол был и на паре моделей винтовок фирмы Вальтер . На них вылечили заменой пластикового приклада на металлический. У ЗИГа 550 из видео тоже схожая конструкция в этом отношении.
How is this a fail?
Bruv you trippin thats normal
Bro don’t Break the Masterpeace or I will find you 😡😡😡
It's a friggin SIG they don't break, Bruder :)
Oh makes sense :)
Главное безопасность. 😄😂🤣🇷🇺🦨
Спуск курка тоже!?😮
Для чего нужна затворная задержка, вот от этого надо исходить. Если для удобства, обозначить что БП всё то, натурально, такая ситуация притянута за уши))
looks like the old sig 550
where is tha fail ?????
Лучший калаш , ога
Оптики не жалко? Сердце кровью обливается при таких кадрах 😢
Там не нужно РОНЯТЬ винтовку, достаточно легкого шлепка по прикладу.
Бля ХА , му ХА !
У меня только один вопрос , приклад резиновый что ли ))
Пластик 🤷
Fail?? Normal
SA80 does this too.
🙈
I have a NEVER fired Right from Factory 552 (LB ) version. MINT. Only 25 EVER imported into US, with folding End. 7K, ffl to ffl shipped.
SIG SG 551
'promo sm' ⭐
Что произошло
Завтор слетает с задержки от удара. Гарантированно)
This is an non issue. All weapon platforms of this type do this.
NOT a malfunction. Typical bored You Tuber trying to make something out of nothing.
That really hurt to watch
Here we go again sig!!!
Yeah, contrary to popular belief they are trash, you are lucky the stock didn't break off... My company alone had 5 broken stocks, about a dozen broken charging handles and a bunch of shattered mags and that's just 100-ish guys.
Maybe the issue here is you? I used it during my service as infantryman and it has seen alot of rough situations. These same guns are used by many different militias and I have not yet encountered anything like you mentionned.
And we had like 200 different rifles in use for 14 months straight...
@@CralluxMaybe because you boys in green are the show ponies with the nice toys while everyone else gets rifles older than the men wielding them?
@@mnk9073 Before you make such bold statments maybe you should inform yourself. We get old and used rifles. Do you really think the army is investing every year for 12000 new rifles for each recruit? If a rifle is worn it gets repaired by the gunsmith. If you're lucky, you'll get a rifle with a brand new barrel while the rest is still old like the gas tube, spring and so on.
My rifle had markings from rust in the barrel and gas tube due to poor maintenance of the previous owner. The rest was ok. It shot well despite its flaws.
Big whoop. Throw out your ar while you are at it
尾部遭到冲击导致自动机反跳很新鲜吗，几把长见识短的玩意儿😅😅😅