Good Content sir. But a small correction. Just like for construction of a building where structural analysis is necessary, it is equally necessary to design post installed rebar applications like these following Eurocode 2 refer Technical Report 023. Just FYI. 10times the diameter is not the right measure of depth.
Hi sir, Can i extend 2.5 feet rcc slab of ground floor length 30 feet just for passage of 1st floor...no loads no wall just slab for passage.. 1st floor outer walls will be on old slab itsef...
Sir Mera gharr 3 manjil bana hua h but ground floor waale kamre m pillar nhi h 9" ki wall h or ab deewar m crack aane lage h load ki vajah se...second floor prr Piller beam dono h
Yeh staircase ke midlanding ka steel missing tha shayed? Yeh kis project ka hai aur kaun si company kaam kar rahi hai? Dekhne mein to barha project lag raha hai.
By doing this you are missing 2 valid points . 1. The joint doesn't become RCC for beam . It's only steel there at beam-wall interface to take care of the load . 2. The beam doesn't get any bearing on wall .
If people start doing rebaring this way, then believe no structure will be safe. It’s absolutely disaster how he is fixing those reinforcements, he is literally hammering them.
@@rbsinghcivilengineeringaca6777 sir 2nd floor ke roof casting me 1 bich me coloum ka 3 sariya roof ke andr hi dab gya galti se rebar ke liye kitna inch andr drill karna hoga
@@rbsinghcivilengineeringaca6777 we can use this method for column extension. Am I right? My column steel bars have corroded, some 16 mm bars have become the size of 10 mm. Can we use this technique for reinforcing the existing column steel bars?
Sir Ji, Chemical to theek hai, Lekin hole 🕳 for 2/3 full kiya Jata hai Pehle. Jaise aapne kiya hai woh itna nahi bhra. Main bhi yehi kaam karta hoon Australia mein. Hum Hilti Use karte hain. Cleaning process bhi aapki thodi aur safai se honi chahiye thi. Brush use karke, fir blower, fir brush fir blower. Chemical anchoring is a serious business and your bond is as good as your hole cleaning. Wear ear muffs and gloves for safety reasons. Be safe and keep up the good work.
Aur bhi ek bat hai ki 20 dia rod k liye drill bit bhi 20 ka hi use kiya, kya ye sahi hai?? 20 dia ka rod rebaring k liye bit kitne mm ka use karna chahiye??
Hilti drilling machine ya Boss drilling machine ka use Karo brother, sath mein steel ki marking jarur kare ta ki ham side me ashani se drilling kar sake.
@@rbsinghcivilengineeringaca6777 ji , thankyou 🙏 so much sir,sir rebarring karna h, plinth Bim me, new constitution h, bathroom k liye , kya chemical use karna compulsory h, pls help me
Good Explanation! But its a layman s way its done, but Rebaring is a very technical topic! Any connection done needs to be designed as for EC2! 10D is death trap, plz avoid!
Sir kisi slab pr M25 dalni thi or galti se M20 dal gyi ho to fir solution kya hoga plz reply. M ye question ka answer kafi time se khoj rha hun plz solution provide kren.🙏
Mr. Kasi ram ji +919561425493 , Already indore madhya pradesh , mein hi hai aap is person se contact karke rate faur chemical ke bare mein pata kar sakte 👍👍
This is an absolutely wrong method of post installed rebar grouting. First of all Rebar grouting methods and principles are defined by European Technical Association and not IS. Also there is no concept of 10XD. That is absolutely wrong. The drilled hole diameter for every rebar size is mentioned by ETA. The cleaning of holes need a brush cleaning along with blower. The way the chemical is injected is wrong. You should use a plug for that. You should always understand that any engineering application should not be causally taken into account.
thank you for video but aap kanjuse karna sikha re ho chemical ko hole ke depth me minimum 70 % fill karna hota hai ta steel andar jane k baad 100% chemical ho
Dear ismein bahut Sare product aate Hain aapko kis kam ke liye chahie, yadi crack repair ke liye aap baat kar rahe hain to near about 500 rs to 700 Rs ke near about per kg padega.
@@6070avm minimum steel inserted in the concrete 10 X dia of Steel, Suppose that steel used in the columns 12mm dia , minimum requirements of steel insert of concrete 120 mm . maybe clear this doubt sir ji.. 👍👍
25 Mm ke rod ko fix karne ke liye to 28 mm ke bit se drill karna chahiye na hammer marne se kamjor hojata hai aur above 16 mm ke rod ke liye fisher ka chemical bahut bekar hai hilti RE 500 hona chahiye
10D is taken and which is important in depth of hole , So that my steel , Dia is 20 or 25mm, Hole depth = 25×10 = 250 mm & 20×10 = 200 mm as per IS code required for rebaring work
Firstly, it is not rewiring it is rebarbing, secondly your method of grouting is wrong, chemical is poured inside the hall at once and it should fill and come out and thirdly your grouting chemical itself is wrong.
दोस्त हो सकता है आपको हमारा वीडियो अच्छा ना लगा हो और जो आपने भेजा है और जो हमारा वीडियो है वह लगभग 90% एक जैसा है कृपया और अधिक जानकारी के लिए आप हमारा वीडियो पूरा देखिए 🙏🙏
@@rbsinghcivilengineeringaca6777 Sir aap European Organization for Technical Approvals ka report TR023 Assessment of Post-installed reinforcing bar connections padh lijiye. Waha pe likha hua hain. Ya phir www.hilti.in pe padh lijiye.
Nice video sir from Tanzania, I am civil engineer really good information..
Good
Thank you sooo much for explaining it in a very simple way with complete details about it without leaving a single point
Good Content sir. But a small correction. Just like for construction of a building where structural analysis is necessary, it is equally necessary to design post installed rebar applications like these following Eurocode 2 refer Technical Report 023. Just FYI. 10times the diameter is not the right measure of depth.
Thank you brother for good suggestion ,, In the next video, reference was made by checking the video above what you have given .
Very innovative idea..thanks 👌
Sir
Rebaring karne se ghar ka structure weak hota hai kya?
Excellent dear amazing explained
Slab ke liye beam bhi joint kar sakte hai. purane colum se please batayega sir
Kitne ghante baad concrete kr skte hai
Sir apka video main Bhahot kuch sikhne ko milta hai
Very good sir
Sir rebaring is code kaya hai?
Long life chalega kya... Coz load will only on rebar ans concrete is just joint another column/beam
Very nice
Very good job sir
Hi sir,
Can i extend 2.5 feet rcc slab of ground floor length 30 feet just for passage of 1st floor...no loads no wall just slab for passage..
1st floor outer walls will be on old slab itsef...
Yes why not.install 4columns for load distribution
Sir but humara pillar ki saria to h but wo galat 9 inch doori par h to uska load chat par aayiga to rebearing kr skte h
Can any one sugest best chemicals brand for rebaring for 18 inch cantilever beam..(this beam will also carry brick wall load)
Sir can we done rebaring in brick structure of 12 inches wall
Very good information sir ji
Good idia
Thank You Sir
Which code 10d??
Mostly max. Dia bar used in bottom layer. As u told 25 dia bar taking top layer and 20 dia bar in bottom.
Excellent for rebar video
Sir Mera gharr 3 manjil bana hua h but ground floor waale kamre m pillar nhi h 9" ki wall h or ab deewar m crack aane lage h load ki vajah se...second floor prr Piller beam dono h
Can we do it for column rod, whenever there is no possibility of clink.
Yeh staircase ke midlanding ka steel missing tha shayed? Yeh kis project ka hai aur kaun si company kaam kar rahi hai? Dekhne mein to barha project lag raha hai.
Nice Sirji.
By doing this you are missing 2 valid points .
1. The joint doesn't become RCC for beam . It's only steel there at beam-wall interface to take care of the load .
2. The beam doesn't get any bearing on wall .
Thanks for tell about depth relation with dia. Of steel bar
For taluka malshiras dist solapur state maharashtra ke liye koi rebar ke liye hai kya
Good
Very nice video
Nice sir
Thank you Bhai 👍👍
If people start doing rebaring this way, then believe no structure will be safe. It’s absolutely disaster how he is fixing those reinforcements, he is literally hammering them.
Aise karne bricks ka weight sahan kar lega?
Beam full load legi bhai as per design.
@@rbsinghcivilengineeringaca6777 ok,mere ghar k bathroom ko extend karna hai 2 ft, contractor rebairing karne ko bola hai,ye safe hoga?
@@kiranbhatia2554 dono site columns hoge tabhi karna.
@@kiranbhatia2554 too beam jada load legi
@@rbsinghcivilengineeringaca6777 ok thanks, 🙏 ye safe to hoga? Pune main rebairing cost approx kitni hogi
Coloum ka v same process hota h?
Yes brother.
@@rbsinghcivilengineeringaca6777 sir 2nd floor ke roof casting me 1 bich me coloum ka 3 sariya roof ke andr hi dab gya galti se rebar ke liye kitna inch andr drill karna hoga
@@Tej_bharadwaj dear column ka steel ka dia kya hai & Slab ki thickness kya hai , please confirm
10×dia of steel, Concrete mein hole karna hota hai minimum..
@@rbsinghcivilengineeringaca6777 we can use this method for column extension. Am I right? My column steel bars have corroded, some 16 mm bars have become the size of 10 mm. Can we use this technique for reinforcing the existing column steel bars?
Very good video sir
Sir Ji, Chemical to theek hai, Lekin hole 🕳 for 2/3 full kiya Jata hai Pehle. Jaise aapne kiya hai woh itna nahi bhra. Main bhi yehi kaam karta hoon Australia mein. Hum Hilti Use karte hain. Cleaning process bhi aapki thodi aur safai se honi chahiye thi. Brush use karke, fir blower, fir brush fir blower. Chemical anchoring is a serious business and your bond is as good as your hole cleaning. Wear ear muffs and gloves for safety reasons. Be safe and keep up the good work.
Very good dear , Next video me aap ki baato ka dhyan diya jaayega..
Thank you for good suggestion..
Aur bhi ek bat hai ki 20 dia rod k liye drill bit bhi 20 ka hi use kiya, kya ye sahi hai??
20 dia ka rod rebaring k liye bit kitne mm ka use karna chahiye??
@@hemalpatels2016 20mm ke rebarring ke liye 24 mm ki bit use honi chahiye
Can any one sugest best chemicals brand for rebaring for 18 inch cantilever beam..(this beam will also carry brick wall load)
@@nanamarkad7832 Hilti has quite good reputation. Better off consulting them before use.
Sir fr that which IS CODE is followed?
Very nice 👌👍
Sir conse hammer se plinth bim ,me hole ho jayega, mere pas tiger ka hammer h, but usse hole ni ho pa rha, pls help me.
Hilti drilling machine ya Boss drilling machine ka use Karo brother, sath mein steel ki marking jarur kare ta ki ham side me ashani se drilling kar sake.
@@rbsinghcivilengineeringaca6777 ji , thankyou 🙏 so much sir,sir rebarring karna h, plinth Bim me, new constitution h, bathroom k liye , kya chemical use karna compulsory h, pls help me
Good Explanation!
But its a layman s way its done, but Rebaring is a very technical topic!
Any connection done needs to be designed as for EC2! 10D is death trap, plz avoid!
ऐक बॉटल मे कितने राड होते 12mm के
6 ईन्च अनदर
Apko krane h kya sir
Apko krane h kya sir
@@s.bproject1406 sir plinth Bim me hole ni ho pa rha tiger hammer se, kya solution hai, pls help me
🙏🙏🙏🙏🙏
Is chemical ko hum log bhi banate hai. Humara company ka nam VIBGYOR INC(Kolkata).
Sir kisi slab pr M25 dalni thi or galti se M20 dal gyi ho to fir solution kya hoga plz reply. M ye question ka answer kafi time se khoj rha hun plz solution provide kren.🙏
Concrete ya steel
Dear 15 days curing proper Karo & Slab ki shuttering 28 days tak rakho .& 28 days ka cube strength yadi 25 N/mm2 aa jati hai too very good..
Kitna time ho gaya hai slab casting Ka.. please share the information..
Cement ki information dena ..
@@rbsinghcivilengineeringaca6777 OPC 43 grade ultratech
iske baad iski testing bhi hotti h ya nhi???
Yes,, pull out test kiya jata hai dear..
Grouting work completed hone ke baad , required strength check karne ke liye..
Lekin sir cmcl lagane k bad gun rakhne par sukh jata h
Chemical lagane ke baad, near about 30 minutes ke baad hi set hota hai..
What are Service charges per hole. Any contact for Indore.
Mr. Kasi ram ji +919561425493 , Already indore madhya pradesh , mein hi hai aap is person se contact karke rate faur chemical ke bare mein pata kar sakte 👍👍
Good👍👍
Column mera side may crck hai us ke liye koi achcha atreeqa batao
Is chemical ka name aur price kya hai plz bataye🙂
Fischer cemical
Good method
Good video
Very nice 👌👌
Very good
Ye hilti ka drill machine nahe he
🙏
Man gye dada
Thanks Dada.. congratulations...
This is an absolutely wrong method of post installed rebar grouting.
First of all Rebar grouting methods and principles are defined by European Technical Association and not IS. Also there is no concept of 10XD. That is absolutely wrong.
The drilled hole diameter for every rebar size is mentioned by ETA.
The cleaning of holes need a brush cleaning along with blower.
The way the chemical is injected is wrong. You should use a plug for that.
You should always understand that any engineering application should not be causally taken into account.
Yes you are right. This is all poor work.
Sir where is this site?
thank you for video but aap kanjuse karna sikha re ho chemical ko hole ke depth me minimum 70 % fill karna hota hai ta steel andar jane k baad 100% chemical ho
Dear 60% chemical hai Bhai..
good work👍
Dr. Sahab thanks for your support...
This is poor work explaining is ok but work is poor
प्लीज इसका रीवा रिंग डॉक्टर फिशर का रेट बताइए कितना मिलता है
Dear ismein bahut Sare product aate Hain aapko kis kam ke liye chahie, yadi crack repair ke liye aap baat kar rahe hain to near about 500 rs to 700 Rs ke near about per kg padega.
Aur yadi aap bada packet Lete Hain to is se kam rate padega.
How many inches of steel should be inserted inside the concrete
Minimum 10 dia of Steel.
concrete insert steel length
@@6070avm minimum steel inserted in the concrete 10 X dia of Steel,
Suppose that steel used in the columns 12mm dia , minimum requirements of steel insert of concrete 120 mm .
maybe clear this doubt sir ji.. 👍👍
@@rbsinghcivilengineeringaca6777 Thank you sir
@@rbsinghcivilengineeringaca6777 , he is asking how many inches ...gaddha mistri ban'na chahiye .
Aisa chidki opar Kalam kia jasakta ha, kyoki chad ki rod sob katahoaaha,
R e Wall ka full form rain force ha kya sir ji
दोस्त , री- वायरिंग का मतलब होता है किसी भी जगह में दोबारा स्टील बार को डालना..
Returning wall
Sir ap India mn e job krty hn?
25 Mm ke rod ko fix karne ke liye to 28 mm ke bit se drill karna chahiye na hammer marne se kamjor hojata hai aur above 16 mm ke rod ke liye fisher ka chemical bahut bekar hai hilti RE 500 hona chahiye
WRONG GROUTING IS CARRIED OUT. FISCHER MATERIAL IS NOT ADEQUATE.
Why sir?
@@jvjv6332This material is not epoxy based. It is vinyl based. Epoxy is better and appropriate for such job.
better to use forsroc Lockfix,,Sastha and Majbooti hai... Baaki sub befaaltu ..
😅❤ 0:37
Nice
Chemical ka naam kya hai
Sir ishka load test kaise karege...
bottle se pahle chemical nikale Nahin sar
Sir iska IS Code Kya ha
How can we calculate rebar drill debth for formula
10D is taken and which is important in depth of hole , So that my steel , Dia is 20 or 25mm, Hole depth = 25×10 = 250 mm & 20×10 = 200 mm as per IS code required for rebaring work
@@rbsinghcivilengineeringaca6777
Sir kindly tell us IS CODE no
Class 5 me join karo . Multiplication sikho useless log .
Machine hilti nhi hai bro... Koi aur company hai
Hello sir the chemical name
Company name, Fisher chemical aur hilti chemical
Sir muje ya chamical chahiye Kha milega
Dear district level main har jagah available
@@rbsinghcivilengineeringaca6777 hamirpur mai mil skti hai
सही से एक्सप्लेन नहीं किया
Very good work, Sir aap ka mobile number mil saktaa hai kya..
Rw wall ka full form kya hi sir ji
Dear RW yahi , rebaring wall Yani , wall mean rebaring work karna
Chemical Ka kya nam he batiye please
Fischer
Firstly, it is not rewiring it is rebarbing, secondly your method of grouting is wrong, chemical is poured inside the hall at once and it should fill and come out and thirdly your grouting chemical itself is wrong.
ये HILTI machin nahi
Kya ye belivebal h
Ur Wala nahi, Larkin system se hona chahiye
Ji
Rebaring aise nahin hoti bhai
Bhai chemical itna daalo ki road daal ne ke baad chemical bahar aaye
Correct,it’s a poor work
Name bataeye na
Kaam करना आता नहीं है और लोगो को बता रहे है की ऐसे होती है री ribarig कितना ml केमिकल डालता है होल मे ऐसे होती है ribarig
Very good dear.. please send the correct methodology for this work...
@@rbsinghcivilengineeringaca6777
Ye video dekh lo🤭🤭
ruclips.net/video/GjP2dGyb4as/видео.html
dost hamare video aur is video mein jyada antar Nahin hai main bhi ho Sakta hai aapane Sahi tarike se video ko Dekha Nahi hai..
दोस्त हो सकता है आपको हमारा वीडियो अच्छा ना लगा हो और जो आपने भेजा है और जो हमारा वीडियो है वह लगभग 90% एक जैसा है कृपया और अधिक जानकारी के लिए आप हमारा वीडियो पूरा देखिए 🙏🙏
Yeh chemical kha milenga?
Aap ko har jagah mil jayega ..
Hilti ka bhi chemical aata hai..
Hilti company ka
Sir very nice.
Ma
Aap re wiring kyu bol rahe ho
Contact me for Pull Out test
Ye bilkul fail method hai
Bar ko thoka nahi jata
Sir ji sahi method ko batao Bhai Kya hai... Civil engineering ka koi 1 methods nahi hota hai ..bahut sari method hote hai..
You are absolutely right. Rebar ko kabhi Thoka nahi jata.
@@rbsinghcivilengineeringaca6777 Sir aap European Organization for Technical Approvals ka report TR023 Assessment of Post-installed reinforcing bar connections padh lijiye. Waha pe likha hua hain. Ya phir www.hilti.in pe padh lijiye.
Very good
Nice