The glitter is by recollections from Micheals. The color is Glitz. I always apply the glitter to one side, with UV resin, then I flip it over, and apply the decal to the other side, and seal with UV Resin.
designbundles.net/graphichousedesign/295751-friends-will-be-connected-by-heart-friendship-quot#gtmList=30>mPos=4 I actually got this as a whole design from this website, so I'm not sure what font was used.
Hi Christy, I have a few suggestions, first try a new blade, if you have changed it more recently you can try cutting on a slightly deeper setting, then third, patience with tweezers and your thumbnail! I have a thing for really complicated cuts, my tweezers and I are really good friends :)
Hi Jana, using on the balcony is great for ventilation, but the sun's ray will start to set it really fast, try using it in a shady spot - or under an umbrella, anything to cover it until you are ready for it to start setting. I use it inside next to a shady open window, and use the lamp to set it.
I, with my infinite mom brain - resined the wrong side I remember correctly... resin should some with a warning - "don't resin half asleep in the middle of the night"
Thank you :) It depends. I often just mix it in with the resin in a little disposable cup. It’s wayyyy less messy. Unless I’m doing the tack-it method (to lay all the glitter flat) I premix it with the resin.
Hello, thanks for the video. Can you tell me please where you get your keychains and jump rings? I can't seem to find any that aren't flimsy and break easily.
I had to look way back! I got them from amazon, and they are really good jump rings - these are the ones I got: www.amazon.ca/gp/product/B07B7PXYGV/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1
@@carakinsley it helps of you're in a warm environment or if you run a lighter over it which will pop bubbles, and allow it to warm up a bit and settle smoother. If that not possible, wait and allow it to settle before curing.
Sometimes if it's being stubborn, I put them in a bright window. The sunlight always works if they are not curing all the way under the lamp! I have a window I often let them sit a few days even when they don't feel sticky.
Hi quick question pls. I bought yhis exact same resin that came with the uv light. Once dried there are these white spota all over in the resin. I did try the lighter to get rid of bubbles etc. Not sure if I even did that right too coz there was a smell 🤦♀️ how do I fix this pls or avoid. Thanks
@@tklcollier2381 I'm not 100% sure to be honest - I haven't had that happen, you can try keeping it somewhere warmer in the house, cold can cause bubbles. Be really careful moving it around the acrylic, some people find using a gloved finger works better to prevent bubbles, or even try a torch, something strong than a lighter to try and really pop them.
hi patty - these are alcohol inks, I got them at Micheals here in Canada, but the US website lists the same ones, they are Tim Holtz brand www.michaels.com/tim-holtz-alcohol-ink-set-mariner/10407285.html wow and they are $6 cheaper for you!! thanks for watching!
I live in Canada - so I use a Canadian Company for my blanks : roshkoinnovations.ca/ the alcohol inks and vinyl are from Michaels and the resin is from Etsy - www.etsy.com/ca/listing/786196565/transparent-clear-uv-resin-hard-type?ref=yr_purchases (she's Canadian) - I know it's available on Amazon, and a few other places Thanks for watching!
www.amazon.ca/Lx10tqy-Non-Toxic-Resin-Ultraviolet-Transparent/dp/B07R4BY4L4/ref=sr_1_32?dchild=1&keywords=uv+resin&qid=1611810514&sr=8-32 this is the brand I use, I have no idea what it's actually called, I just look for the label.
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
So pretty
Beautiful!
Thank you!
I'm so glad i stumbled upon your video, your work is awesome. I'm just a beginner so your video really helped me
SUPER !!!!! ❤❤❤
Beautiful work, love it
Wow! Love it❤️
Beautiful ❤
Looks beautiful!
My I ask what is the thing you put on your finger and what is it called.
This is beautiful! What is the brand and color of glitter you used, please?
Also, which side did you apply the decal to?
Tia!
The glitter is by recollections from Micheals. The color is Glitz. I always apply the glitter to one side, with UV resin, then I flip it over, and apply the decal to the other side, and seal with UV Resin.
What font did you use for the wording the round... Side by side etc
designbundles.net/graphichousedesign/295751-friends-will-be-connected-by-heart-friendship-quot#gtmList=30>mPos=4
I actually got this as a whole design from this website, so I'm not sure what font was used.
Where did you purchase your image for or did you use Cricut?
I bought from a site called design bundles.net they have tons of designs and near of the end of every month you have huge bundles for $1!
Amazing!! Definitely going to try this. My question is that when I go to cut my letters like that. I lose some.. too small
Hi Christy, I have a few suggestions, first try a new blade, if you have changed it more recently you can try cutting on a slightly deeper setting, then third, patience with tweezers and your thumbnail! I have a thing for really complicated cuts, my tweezers and I are really good friends :)
Wonderfull
Hello. I have tried uv resin but it dries very quickly. I used it while on a balcony .. Give me some tips please. Thanks
Hi Jana, using on the balcony is great for ventilation, but the sun's ray will start to set it really fast, try using it in a shady spot - or under an umbrella, anything to cover it until you are ready for it to start setting. I use it inside next to a shady open window, and use the lamp to set it.
Ohhhh what did you do with the little one???
I, with my infinite mom brain - resined the wrong side I remember correctly... resin should some with a warning - "don't resin half asleep in the middle of the night"
Can i use acrylic paint and then uv resin?
Yes. The resin will seal in the acrylic.
Hi. These are amazing. How do you mix glitter with the resin- or do you just sprinkle over?
Thank you :) It depends. I often just mix it in with the resin in a little disposable cup. It’s wayyyy less messy. Unless I’m doing the tack-it method (to lay all the glitter flat) I premix it with the resin.
@@AnDIYcraft thanks
Hello, thanks for the video. Can you tell me please where you get your keychains and jump rings? I can't seem to find any that aren't flimsy and break easily.
I had to look way back! I got them from amazon, and they are really good jump rings - these are the ones I got:
www.amazon.ca/gp/product/B07B7PXYGV/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1
Thank you 😊
Love it what size is you larger circle acrylic. ? 3”?
yes it's a 3 inch blank
Is that a stamper your using for the alcholic ink
It’s a felt stamper. Just from michaels. In the alcohol ink section.
@@AnDIYcraft thank you
My resin always comes out bumpy even though i feel i am spreading it equally. Any tips on how to accomplish a smoother finish would be appreciated.
@@carakinsley it helps of you're in a warm environment or if you run a lighter over it which will pop bubbles, and allow it to warm up a bit and settle smoother. If that not possible, wait and allow it to settle before curing.
Mine stays tacky ..I keep putting back under the light ...any avice...I have let's resin
Sometimes if it's being stubborn, I put them in a bright window. The sunlight always works if they are not curing all the way under the lamp! I have a window I often let them sit a few days even when they don't feel sticky.
@@AnDIYcraft thanks so much I will try that...
Can I use watercolour to color the resin keychain?
I'm not sure, depending on the ingredients, but water can effect how it cures
@@AnDIYcraft Thank you so much 😍
Hi quick question pls. I bought yhis exact same resin that came with the uv light. Once dried there are these white spota all over in the resin. I did try the lighter to get rid of bubbles etc. Not sure if I even did that right too coz there was a smell 🤦♀️ how do I fix this pls or avoid. Thanks
I only use the uv resin on its own to seal the vinyl writing on acrylic (keychain) so its clear
@@tklcollier2381 I'm not 100% sure to be honest - I haven't had that happen, you can try keeping it somewhere warmer in the house, cold can cause bubbles. Be really careful moving it around the acrylic, some people find using a gloved finger works better to prevent bubbles, or even try a torch, something strong than a lighter to try and really pop them.
@@AnDIYcraft thank you will try that 🤗
hi what brand of paint is good. im in usa
hi patty - these are alcohol inks, I got them at Micheals here in Canada, but the US website lists the same ones, they are Tim Holtz brand
www.michaels.com/tim-holtz-alcohol-ink-set-mariner/10407285.html
wow and they are $6 cheaper for you!! thanks for watching!
Can you tell me where you got you stuff from
I live in Canada - so I use a Canadian Company for my blanks : roshkoinnovations.ca/
the alcohol inks and vinyl are from Michaels
and the resin is from Etsy - www.etsy.com/ca/listing/786196565/transparent-clear-uv-resin-hard-type?ref=yr_purchases (she's Canadian) - I know it's available on Amazon, and a few other places
Thanks for watching!
How did you print the names?
They are cut out of vinyl - I used a cricut
What brand of resin are you using?
www.amazon.ca/Lx10tqy-Non-Toxic-Resin-Ultraviolet-Transparent/dp/B07R4BY4L4/ref=sr_1_32?dchild=1&keywords=uv+resin&qid=1611810514&sr=8-32
this is the brand I use, I have no idea what it's actually called, I just look for the label.
Great video! Music is honestly terrible
neat tutorial, just keep the volume on mute :)
Nice work, beautiful keychain - but annoying repetitive music. oh ohohohohoohohohohoh.OY
Thanks! and sorry about the music it’s an old video