Plumbing Rough In - Laundry Plumbing (EP6) - The Building Expert 2022
HTML-код
- Опубликовано: 26 сен 2022
- Plumbing Rough In - Laundry Plumbing (EP6) - The Building Expert 2022
In this video we are plumbing a three-piece laundry room. Very basic configuration with sink on the left side, washer in the middle and dryer on the right side. There two other vents coming from the basement which we connected with the laundry vent & penetrated one through the roof.
In this video we also talked about efficiency, common plumbing codes & interior design specs.
If you have any question, comment or suggestion for a video please comment below.
Subscribe to our channel and be the first to know about new uploads.
Enjoy!
#TheBuildingExpert #laundry #plumbing #building
Concept: Manvir Badyal
Instagram: thebuildingexpt
RUclips: @TheBuildingExpert
© Copyright 2022 The Building Expert (Manvir Badyal). All rights reserved.
DISCLAIMER: The Building Expert make videos to share the knowledge we have gained over the years related to construction. We are not responsible for any damage done to a property if someone decides to do their own plumbing by watching our videos. Always consult with a licensed builder/plumber before starting a project.
Nice thanks
Do you have a video of tying plumbing for the sink & washing machine to the drains under the house?
Goode job
You didn't remove burrs after cutting the PVC before applying adhesive???
Question my laundry is a French laundry it only has. A sink and how do I connect the washing machine to it ? No taps in the walls my plumber fkd up I think !
Can. Use divertor connect it under the sink to the main water pipe and t it to the washing machine ?
I install laundry in basement where it has wet went drainline nearby, is it valid? 2nd, I want to install a kitchen sink as well. what is the minimum separation of those two wye fittings and what if the vertical pipe is at 45 degree angle ? thanks
Good job
Good job. Looks good!
Thanks!
Can I install a new utility sink drain pipe to the plumbing cleanout?
You can lol but its not legal it won’t vent right it’s already wet venting as it is
no cleanout stands along for respecting code
Gluing ABS. I noticed that you're not following the correct manufacturer's procedure for connecting pipes; Cutting AND DEBURRING the ends, making sure the surfaces of the pipes to be joined are WIPED CLEAN of any dust/dirt, applying glue to BOTH SURFACES of the connecting pipes (and not just one), giving the glued pipe end a quarter turn AND HOLDING IT IN PLACE SECURELY for several seconds. The container from which you are getting the glue from APPEARS OLD AND DIRTY with lumped up glue (with sawdust mixed in) at the top. I'm assuming the glue may contain debris from the job or a past job, etc. Yes, you are working fast, but why introduce a problem(s) at this critical step of connecting and sealing ABS pipes?
I a plumber in Chicago, Illinois, this plumbing work never passes a rough-in inspection here 🥵
1) abs not allowed
2) Every laundry needs a grey box.
3) wet vents are not allowed
4) Every laundry room requires a floor drain
5)vents separate for each discharge opening
Wet vents must be allowed. How do you vent floor sinks in a restaurant, or mechanicalroom? Combination drain and vent, i.e. a wet vent. Also bathroom groups allow a wet vent.
your code is tighter than a nuns… nvm
Floor drain may not be necessary because it's residential (house)
He used 1 1/2 pipe for a laundry sink and washmachine.. that's nuts. He needed 2 inch pipe
1 1/2 pipe for a wash machine and it has a laundry sink on it. Not good.. you need 2 inch pipe ..🤯
The washer has 2 inch pipe. The San tee he used for the sink is a 1 1/2 x 2
Not a single cut deburred. Good grief.
Most codes (upc) requires a 2 inch trap to drain to a 3 inch stack or drain.