What Happens When You Ask The Internet For Help. Testing Bobcat suggestions from Face Book groups.

Troubleshooting the arm bar sensor based off information we found on the internet.
www.4tetradgro...
Tools We Use:
Hydraulic Cylinder Spanner amzn.to/3SAlHYw
Another Spanner Option amzn.to/3LR1JFb
Hydraulic Seal Clasper www.4tetradgro...
Hydraulic Seal Stretcher www.4tetradgro...
Injector Block Off Cap www.4tetradgro...
Bobcat Fuel Filter Bowl Wrench www.4tetradgro...
Wrench Extender amzn.to/3Yt2yvl
Spring Compressor Tool amzn.to/4fA030n
Hydraulic Seal Installation Kit amzn.to/3Yrs6sV
Hand Impact Tool amzn.to/3Sz0yOk
Common Rail Fuel Injector Test Kit amzn.to/4dasD6T
Injector Leak Back Test Kit amzn.to/46Btf3i
Electrical Supplies:
Milwaukee Solder Iron amzn.to/4dpp0cY
Tesa Harness Tape amzn.to/3SAdG60
X Fasten Harness Tape amzn.to/4cbItNA
Non-Insulated Terminals amzn.to/4dp18XH
Short / Open Tester Power Probe amzn.to/3WRdrpu
Power Probe Master Kit amzn.to/3WPETUR
Shop Supplies:
Gloveworks Nitrile Gloves amzn.to/3WADdwW
Oil Absorbent Pads amzn.to/4ckYq48
Absorbent Pads amzn.to/3WOX64P
Brake Cleaner (Its Really Good) amzn.to/3yse3sA

[@davidjackson4112]

This is while I enjoy your channel. Extremely educational. Thanks again.

[@marcusheron4980]

I'm a tech too and greatly appreciate and value your work. Thank you for the help.
I get some machines that are not safe to operate anymore but the customer insists they can be "safely" repaired and put back into service.
The last 743 i "fixed" is an excellent example.
Customer stated the machine will move but arms won't tilt or lift/come down. Machine already creeps as soon as it's on because there are no brakes left and the centering blocks are already worn on both sides after flipping them.
I go to the gin and look at their machine. It has wires running everywhere that they "repaired" previous problems with.
After testing everything and finding current on every wire including grounds I was lost as hell.
Turns out they had a major short to ground through the charging circuit. The entire mainframe was now a conductor.
I figured this out when I was testing grounds and had my hand against the alternator ground while checking the bics valve. Shocked the hell out of myself. To solve this they made a ground system kill switch they turned on whenever they needed the machine.
I immediately stopped work, notified my supervisor and he called the customer.
They asked if I could "hot wire" the entire bics circuit. Boss said yes but it would be stupid and dangerous. Customer agreed and wanted it done anyway.
I ended up having to wire the lift, tilt and bics valve together to a separate relay and switch that was insulated by a rubber block and grounded to its own circuit.
This made the machine usable again but means that as soon as it has power the machine will move and operate even if the operator isn't ready.
This definitely isn't ideal especially if there are operators that are not familiar with the machine.
The machine was still in reasonably good running order besides the extra wires and was definitely worth a new harness but customer declined because it was working fine now.
I'm pretty sure that will be the last repair possible on this machine without a new harness.

[@alvinmitchell6799]

I had to laugh at the Bobcat tech asking me how I had disabled the door switch on our R series, Ours did not come with a door. When I said that I have not torn into the cover to see how it was connected from the factory.

[@thedelcodave]

I like your little diagnostic voltage regulators that is an excellent way to test sensors on a computerized machine. I was working on a old mini excavator no computer that would start but not operate. I had to get it off the trailer so I applied 12v directly to the solenoids on the spool valve body to disable the various safeties it worked but like you said not the safest option.

[@T18skyguy]

Great video. That's a cool little plug in tester. Did you make that or where did you buy it? Would that work on an R series excavator? Thanks

[@ericrumpel3105]

Thanks fer sharing your vast experience & knowledge !!

[@matthewjuby8660]

I'd love to get my hands on that voltage regulator.UPDATE: Found one...
I believe the switch is not magnetic but an Eddy current proximity probe first introduced by Bentley-Navada. Lots to research. Thanks again for the lesson. Keep it going. Best channel!

[@markhindman9005]

Nice video and informative.

[@marksupplyco]

Ok where can I buy the adjustable voltage regulator it would be for trouble shooting or getting a machine on the trailer and in the shop Thanks Nick Miller

[@tetradgroup]

I have six of these with different connectors to test multiple circuits without having to change the wiring every time. amzn.to/48tjDbf

[@marksupplyco]

@@tetradgroup thank you I found them last night. I am going to make up some for the different series machines. I love your videos have watch for a long time! Thanks Nick

[@noprefixamerican4743]

If I get an answer from you I'm good 😂

[@popeofwrenching4357]

Some of those “pro tips” are going to let the smoke out 😅

[@mookfaru835]

You should of started at a lower output voltage, just in case you overvolt the system and short something out.

[@19bboyricky]

How can I get that device to regulate voltage

[@mikemccrary9346]

So I have a question if the machine is not running and you can’t get it running and you need to transport it to the shop and you have a trailer is it possible to put the track loader in neutral so it will roll so I can drag it up onto a trailer and if so how

[@tractorguy]

Would love to see a video series on what your doing with your S250. Mine just turned over 4000 hard hours today. I keep thinking one of these days something big is going to break, but it just keeps going. I am having an issue, and I’d like to ask you a specific question, but I can’t remember how you wanted us to message you directly. Could you let me know the proper way that you would like to be contacted?

[@tetradgroup]

Ill see if I can get some footage of the S250, thanks for the suggestion. [e-mail]

[@jondelucia9948]

Hey Grady; Jon Silver Springs florida, I have a question I need to send you $20.00 like last question, how to I send it?

[@tetradgroup]

[e-mail]

[@tomnguyen7685]

Can you please make video change axle bearing for bobcat s70.

[@Troubles_Diesel]

Run a toggle switch. Twist singal and hot together. And then run ground by it's self. The switch will work as if the door was on the machine.