@@LowBuckGarage yea, It needs a lot of bodywork but it runs and drives. We are going to redo most of the body panels ourselves using a sheet metal bender and cutter. I live down in the Caribbean on a small island called st.Vincent (it’s 19 miles x 11 miles) so there isn’t really any off-roading trails but I’m sure I’ll find somewhere to have lots of fun.
@@jarednichs3450 I had to look up the island, looks nice from the satellite view! A CJ-2A is a nice small vehicle for maneuvering, and the low top speed shouldn't be a problem there. Good luck with your project!
@@LowBuckGarage the roads down here suck. Driving on the road isn’t much different from off road. The island is amazing, the beaches are stunning and boating is fun.
Jared, are you recording you rebuild on your cj2a? I'll check your channel to see. Perhaps you might enjoy following along as I get my late father's 1958 Plymouth Suburban back on the road. ruclips.net/video/9jJxV_qSNmg/видео.html
Although I don’t own a Jeep and likely will never own one, this has become my favorite channel. Your dry sense of humor and lack of editing out mistakes and things breaking are awesome. It reminds us at home that projects don’t always go as planned for others too.
You have delved much more deeply into the black magic of making crap run. You have my respect. I enjoy watching your videos, and your comedy central quality quips.
If you can't find a salvageable F-head block, but want an F-head engine, and you also have a usable head, cam, and intake valve-related parts from an F-head engine,, you can convert a usable 4-134 L-head block to make an F-head engine. I saw one decades ago, built by the local Willys dealer, who was a very competent engine rebuilder. The only modification he made to the L-head block (besides substituting the F-head cam) was driving out the intake valve guides. The F-head gaskets covered the L-head intake ports. This conversion was possible for the 4-134, but couldn't be done for the 6-161, because the block castings were too different between the L and F head versions of the 6-161.
I have revived some old badly worn engines in my earlier years, but never anything close to what you have been able to do. Everyday I wish I was able to still do this kind of stuff, but getting old sucks! I can still do some of it but it takes me forever and I lose interest. These older videos of yours are coming up and I just keep watching and enjoying every minute of them.
Hiya. Just started watching this clip for the second time. And realized there was a Tonka dump truck on the floor behind you. Greatest toys ever. I'm 57 and I still have my dump truck and front end loader that I got over 50 years ago lol. I must have had a lot of fun with them over the years.
Now I just clicked on this video, and this right here is the content I am looking for. "I have 5 seized, stuck, junk motors, and I am going to have something running by the end of this video!!!" YES, that's awesome, let's go!!!
I have a Model A that had a crack similar to your Jeep. Since the A is a non pressure system I used brass screws as a stitch system. I drilled a hole and tapped it. Used red locktite to glue the screw. Cut the screw off after the lock tite sets. Then repeat the process overlapping the screws a bit so they interlock each one a bit. It works perfectly!! I was also able to get JB weld on top of my stitch inside of the head in the water jacket area.
LBG, I really enjoyed this after spending the whole day clearing dead falls, skidding logs and cutting some slabs with my hacked up alaskan chainsaw mill. Trying to get my boots off maybe watch another one. Thanks for the video!.
I'm a relatively (June 2021) new owner of a m38 and a second l134.... and after watching this, I think I can safely say, you're my Go-Devil engine hero. Your videos have made me realize that it doesn't have to be perfect, and I can focus on getting it running to have some fun, before I stress over getting it perfect.
Thanks, I sure appreciate that! I've been doing this for decades, and I've never had something perfect. I have had as much fun playing with cars as anyone out there, though!
Well I know Willy's Works had been trying to clean up the yard...I had an F Head on an M38A1 that I unfroze little by little. Finally I put .60 over sleeves (Willy's Works) she ran like a champ and climbed like a ram.
Hi James, I only recently discovered your channel, and now I've fallen down the rabbit hole of old vids like this one. As a Brit, most of these vehicles and engines are new to me. I love the half-tracks BTW... And the F-heads... I have never seen an engine that was side valve and overhead valve at the same time! fascinating! And the 2 cylinder air-compressor modification - cunning! Oh, and valve spring compressor 3.0 - Genius! I love the casual "whatever" attitude, which is obviously backed up by a lot of hands-on experience.
Really like the videos. Some might not understand or turn up their nose at doing some things the way you do them even if it's in fun . That said the way things are headed in this country a fellow must be resourceful and be able to make due with what you have or get by with bare minimum. A good skill to have in my book.
Yup, when the connecting rod isn't connecting it's definitely a problem... Excellent video as always, I had no doubt that you would get at least one runner out of the bunch 👍
Always good to take a pile of old junk motors and get some good out of them. Great to finally see one of those compressor heads I have been looking for. Your channel is making me get into my pile of willys
I'm getting motivated to tinker watching you. I have a smattering of Jeeps and Dodges. Commando, scrambler, 53 pw, 51 pw and spare 50, I think two wheel. Then 06LJ daily rig. So, I have plenty to work with. Enjoyed the video. Thank you.
I've also learned to use Permatex #2 on the head studs or any bolts that go through into the water jacket. It seals great and makes them super easy to remove later if needed ✌
That is a good idea, actually that's the exact stuff I used when I put in the head studs. Somehow I forgot to mention it in this video, but I will make a point of it when I replace the bolt in the manifold. Thanks for the heads up!
I Have learned a few nifty tricks from you ,here's 1 from me. Rusted bolts/ studs, get a stick welder 200 amp or more. 500 works great or a car battery but be careful,i t won' t like what you are about to do . clean a very g ood ground on the block, then clean very good place on the stud/bolt. Clamp vise grips tightly on the stud. then make the connections to the welder/ battery jumper cables. Be Quick there will be a spark. In a few seconds you will see a puff of smoke from where the stud screwed in and the stud will come right out ! I think it works by vaporisng the rust because rust doesn't conduct electricty nearly as well as good steel .
Audio sounds like you have your head in a bucket, but good fun to see you rescue one of them. Maybe it will go in the frame that you discovered at the mine?
Nice job getting those engines sorted. The hi-detergent diesel multigrade oil is a good thing for this type engine build as it will clean all the junk out and probably even stop it blowing smoke.
Cool video, but the new engines with 248 sensors, cam phasers,crank triggers torque to yield bolts, MAF and MAP, TPS, FPR, Evap, VVT controlled by ECM's are much easier to work on and more better at saving trees and polar bears.
I've had stuck piston luck by taking a 75%atf and 25% gas mix and put about a half inch in the cylinder. Light it on fire and let it burn out. Then start tapping with a wood block.
Had an uncle put an f-head in a 46 cj2a. had to turn from motor mount around, and cut a hole in the hood for the carb to stick out. the cj3 had a taller hood. PS he robbed the f-head out of a 60s mailster LOL
Almost forgot, I had an old cat with a stuck engine. After a long, VERY LONG time of beating on the pistons, I decided to take the rod caps off, and voila! I got the crank to turn, which allowed the pistons to come loose. A mouse had climber into the cylinder via the exhaust and made a nice comfy lodge....which locked the engine up!!
The L Head is far better than the F Head, Finly got rid of them and went with a 1957 champion 6. The F head has a thin spot on the head gasket and the L head didn't have that thin spot also chrome rings from J C Witney made it run the best. Many Moons ago 1973. I Love Willys
If you need to get a tap to go in real straight, I like using an old timey bit brace, the older ones with two v jaws grab the square tap end great. The handle is longer so you can be more precise in the angle.
On that compressor motor, how did the two cylinders that was pumping air got lubricated? They must have because it was the cylinder that fired wich was bad. Sweden here👍
The crank is pressurized with oil, so it comes out the rod bearings and splashes all over, including the cylinder walls. It comes in from the bottom, and that does a pretty good job.
I will look to see what kind of motor it is but my dad had a motor that was a airconpress motor. going to junk it any way ran but only pump 60 psi. gregg Logan
Time and exposure. They had been sitting unused for well over 10 years each, some well over 20 years. Also bad storage, like being left without spark plugs (the #1 L-head), or left in the woods with an open carb (#1 F-head). It is a good idea to spin motors over every few years, and use a fogging oil if you know you're going to let it sit for a long time. I'd try to move them every 5 years or so, depending on your climate. Surface rust will start forming in the cylinders a few years before it seizes, so when they're hard to turn over at first get some extra oil in the cylinders.
Hey, great vids, any tips on unsticking valves in an l head jeep motor, when they are down flat to the block, and stuck in, possibly at the valve seat and the valve guide both? Thanks,
I usually let it soak for a while and work the cam lobe back and forth to lift it. You might be able to sneak a drift through the port and tap it upwards. That could destroy the valve if its really stuck, but valves are cheaper than replacing a cam.
The camera on the piston showing the bore was directorial genius :)
Bravo
Yeah, that was pretty cool. I watch several car channels, but have never seen that camera trick.
"...So I made a meatloaf" its been 2 years and still no Low-Buck Kitchen
This is quickly becoming my favorite channel. I’m currently restoring a cj2a with my dad (I’m 16) and I’m loving every single second of the process
Thanks! That's a good vehicle to work on, and fun to drive afterward!
@@LowBuckGarage yea, It needs a lot of bodywork but it runs and drives. We are going to redo most of the body panels ourselves using a sheet metal bender and cutter. I live down in the Caribbean on a small island called st.Vincent (it’s 19 miles x 11 miles) so there isn’t really any off-roading trails but I’m sure I’ll find somewhere to have lots of fun.
@@jarednichs3450 I had to look up the island, looks nice from the satellite view! A CJ-2A is a nice small vehicle for maneuvering, and the low top speed shouldn't be a problem there. Good luck with your project!
@@LowBuckGarage the roads down here suck. Driving on the road isn’t much different from off road. The island is amazing, the beaches are stunning and boating is fun.
Jared, are you recording you rebuild on your cj2a? I'll check your channel to see.
Perhaps you might enjoy following along as I get my late father's 1958 Plymouth Suburban back on the road. ruclips.net/video/9jJxV_qSNmg/видео.html
Although I don’t own a Jeep and likely will never own one, this has become my favorite channel. Your dry sense of humor and lack of editing out mistakes and things breaking are awesome. It reminds us at home that projects don’t always go as planned for others too.
Thank you, I'm really glad you like it!
That one oil pan was like a gift basket
Probably one of my favourite channels
Thanks!
This is one of my favorite channels also.
You have delved much more deeply into the black magic of making crap run. You have my respect. I enjoy watching your videos, and your comedy central quality quips.
If you can't find a salvageable F-head block, but want an F-head engine, and you also have a usable head, cam, and intake valve-related parts from an F-head engine,, you can convert a usable 4-134 L-head block to make an F-head engine. I saw one decades ago, built by the local Willys dealer, who was a very competent engine rebuilder. The only modification he made to the L-head block (besides substituting the F-head cam) was driving out the intake valve guides. The F-head gaskets covered the L-head intake ports. This conversion was possible for the 4-134, but couldn't be done for the 6-161, because the block castings were too different between the L and F head versions of the 6-161.
That is an interesting idea, I'm going to try fitting some parts together!
I have revived some old badly worn engines in my earlier years, but never anything close to what you have been able to do. Everyday I wish I was able to still do this kind of stuff, but getting old sucks! I can still do some of it but it takes me forever and I lose interest. These older videos of yours are coming up and I just keep watching and enjoying every minute of them.
You have the fancy pants "will it start" brigade beaten by a country mile...kudos....
Thanks, I sure appreciate that!
I done sat here and watched 7 of your videos. I think I'm addicted.
Hiya. Just started watching this clip for the second time. And realized there was a Tonka dump truck on the floor behind you. Greatest toys ever. I'm 57 and I still have my dump truck and front end loader that I got over 50 years ago lol. I must have had a lot of fun with them over the years.
Now I just clicked on this video, and this right here is the content I am looking for. "I have 5 seized, stuck, junk motors, and I am going to have something running by the end of this video!!!" YES, that's awesome, let's go!!!
I love your sense of humor as you go about the process of evaluating these engines
Thank you!
I have a Model A that had a crack similar to your Jeep. Since the A is a non pressure system I used brass screws as a stitch system. I drilled a hole and tapped it. Used red locktite to glue the screw. Cut the screw off after the lock tite sets. Then repeat the process overlapping the screws a bit so they interlock each one a bit. It works perfectly!! I was also able to get JB weld on top of my stitch inside of the head in the water jacket area.
LBG, I really enjoyed this after spending the whole day clearing dead falls, skidding logs and cutting some slabs with my hacked up alaskan chainsaw mill. Trying to get my boots off maybe watch another one. Thanks for the video!.
Glad you liked it! Sounds like you were having some fun, too...
We've got a winner! U R the best host. Thanks.
Man that was one of your best. I was watching intently! Nicely done, sir!
Thanks, I'm glad you enjoyed it!
Great job getting one out of five going. The stuck piston one is the most interesting to me.
Another great episode and just another day for the LBG.
Thanks!
I'm a relatively (June 2021) new owner of a m38 and a second l134.... and after watching this, I think I can safely say, you're my Go-Devil engine hero. Your videos have made me realize that it doesn't have to be perfect, and I can focus on getting it running to have some fun, before I stress over getting it perfect.
Thanks, I sure appreciate that! I've been doing this for decades, and I've never had something perfect. I have had as much fun playing with cars as anyone out there, though!
My favorite toy right now is a stock '67 M715. It runs and drives but has carb issues, and I love it.
Well I know Willy's Works had been trying to clean up the yard...I had an F Head on an M38A1 that I unfroze little by little. Finally I put .60 over sleeves (Willy's Works) she ran like a champ and climbed like a ram.
I never managed to get out there this past trip, I've got to check that place out...
That's pretty cool about the compressor application. Never heard of that before.
Hi James, I only recently discovered your channel, and now I've fallen down the rabbit hole of old vids like this one.
As a Brit, most of these vehicles and engines are new to me. I love the half-tracks BTW... And the F-heads... I have never seen an engine that was side valve and overhead valve at the same time! fascinating! And the 2 cylinder air-compressor modification - cunning!
Oh, and valve spring compressor 3.0 - Genius!
I love the casual "whatever" attitude, which is obviously backed up by a lot of hands-on experience.
Very nice... having a lot of stuff is always a game changer... Fantastic...
Really like the videos. Some might not understand or turn up their nose at doing some things the way you do them even if it's in fun . That said the way things are headed in this country a fellow must be resourceful and be able to make due with what you have or get by with bare minimum. A good skill to have in my book.
Thanks, I really appreciate that!
Yup, when the connecting rod isn't connecting it's definitely a problem... Excellent video as always, I had no doubt that you would get at least one runner out of the bunch 👍
Thanks 👍
Always good to take a pile of old junk motors and get some good out of them. Great to finally see one of those compressor heads I have been looking for. Your channel is making me get into my pile of willys
I'm getting motivated to tinker watching you. I have a smattering of Jeeps and Dodges. Commando, scrambler, 53 pw, 51 pw and spare 50, I think two wheel. Then 06LJ daily rig. So, I have plenty to work with. Enjoyed the video. Thank you.
Great job I love watching you bulldog through these types of projects, I could watch it every day. Cheers from Jacksonville Florida 🌞
Thanks, glad you enjoy it!
I've also learned to use Permatex #2 on the head studs or any bolts that go through into the water jacket. It seals great and makes them super easy to remove later if needed ✌
That is a good idea, actually that's the exact stuff I used when I put in the head studs. Somehow I forgot to mention it in this video, but I will make a point of it when I replace the bolt in the manifold. Thanks for the heads up!
This just a great channel. I am glad it popped when I was viewing Vice Grip Garage.
I just recently discovered your channel and it's becoming one of my favorites along with This N That garage.
Keep those videos coming!
I learned a lot in one hour ! may have to review that a few more times .
Thanks, glad it was helpful!
35:50 - this is exactly why I grab old tools when I come across them. I restore them and then they work better than many of the new ones.
Willys Jeep motors and I have something in common: I've been called an F-Head too.
The l head are known for cracks by distributor, oil filter some run them some don't, it only filter very little, great job
another fun show john
Definitely enjoyed this one I hope to see it move in the next one
Thanks, I'll get it going eventually!
I wonder with how much of a big bang motor no. 2 went of👀👀🤕🤯
Hi again , I'm glade you got it running ,have fun playing with it .
Thanks, will do!
I Have learned a few nifty tricks from you ,here's 1 from me. Rusted bolts/ studs, get a stick welder 200 amp or more. 500 works great or a car battery but be careful,i t won' t like what you are about to do . clean a very g ood ground on the block, then clean very good place on the stud/bolt. Clamp vise grips tightly on the stud. then make the connections to the welder/ battery jumper cables. Be Quick there will be a spark. In a few seconds you will see a puff of smoke from where the stud screwed in and the stud will come right out ! I think it works by vaporisng the rust because rust doesn't conduct electricty nearly as well as good steel .
Thanks for the tip, I haven't heard that one before! I'll give it a shot on the next broken one.
Nice with the trans am front. BEST CHANNEL ON YOU TUBE. Cheers.
What? No duct tape or tie wire. 🤔 great video. Thank you. It may not be perfect but it works
Audio sounds like you have your head in a bucket, but good fun to see you rescue one of them. Maybe it will go in the frame that you discovered at the mine?
Thriller! Can't stop watching
Nice job getting those engines sorted. The hi-detergent diesel multigrade oil is a good thing for this type engine build as it will clean all the junk out and probably even stop it blowing smoke.
Thanks! It did actually clear up, I'm running that motor in the covered wagon, and there's no smoke at all now.
Another great session LBG. Watched again in one sitting. Plaudits also for your editing.
Thanks, I appreciate that!
That is some impressive base in the first twenty seconds of this video. Like.
Belated thanks to Other Person with the camera, that focused in on Oil Pressure gauge early on.
WOW!! Very unconventional but very resourceful to say the least..good job sir…
Thanks!
Just a weee bit of blow by:)
Oh yeah, it cleared out all the mosquitoes for a while! I'll see what happens with a few heat cycles, it was getting a little bit better near the end.
Cool video, but the new engines with 248 sensors, cam phasers,crank triggers torque to yield bolts, MAF and MAP, TPS, FPR, Evap, VVT controlled by ECM's are much easier to work on and more better at saving trees and polar bears.
You could also sleeve that one cylinder with the wrist pin gouge.
I like your valve spring thingy
I've had 22 Willy's over the years but still have Betsy my 54 cj3b. i have a collection of engines trans and transfer cases etc
I've had stuck piston luck by taking a 75%atf and 25% gas mix and put about a half inch in the cylinder. Light it on fire and let it burn out. Then start tapping with a wood block.
Thanks for the tip, I never heard that one before. It would make sense as it would expand the cylinder and add oil at the same time.
Had an uncle put an f-head in a 46 cj2a. had to turn from motor mount around, and cut a hole in the hood for the carb to stick out. the cj3 had a taller hood. PS he robbed the f-head out of a 60s mailster LOL
I love Low buck garage and metalshaper equally… But I’ll bet low buck garage drives Brian crazy!
Thanks, he does really good stuff! He would definitely cringe at a lot of the things I do...
I know I'm a little late to the party, but I'm going to take out an old but running f head. If you might still need/want one, let me know.
Almost forgot, I had an old cat with a stuck engine. After a long, VERY LONG time of beating on the pistons, I decided to take the rod caps off, and voila! I got the crank to turn, which allowed the pistons to come loose. A mouse had climber into the cylinder via the exhaust and made a nice comfy lodge....which locked the engine up!!
I am still looking for one, my email is james@low-buck-garage.com If you could email me details and location I'd appreciate it. Thanks!
impresive work !
I was really rooting for the F-head. Wonder what one of those giant valves can flow?
Ok, this one was awesome! Subscribed!
hi…love your videos,…i guess you never heard of Marvel Mystery Oil…instead iof beating up the pistons…i used it on boat sinkers, worked very well…
^.-.^ all these wee vids qre giving me the itch to play out in the garage.
The L Head is far better than the F Head, Finly got rid of them and went with a 1957 champion 6. The F head has a thin spot on the head gasket and the L head didn't have that thin spot also chrome rings from J C Witney made it run the best. Many Moons ago 1973. I Love Willys
If you need to get a tap to go in real straight, I like using an old timey bit brace, the older ones with two v jaws grab the square tap end great. The handle is longer so you can be more precise in the angle.
I like that idea, I'll have to give it a try!
I like that ideal.
i have had good luck with CLR for freeing pistons
I had fun watching this video!
Mission accomplished!
Awesome!
Those L-head engines are very sought after here in Sweden, easy $500 for a stuck one with missing parts.
On that compressor motor, how did the two cylinders that was pumping air got lubricated?
They must have because it was the cylinder that fired wich was bad.
Sweden here👍
The crank is pressurized with oil, so it comes out the rod bearings and splashes all over, including the cylinder walls. It comes in from the bottom, and that does a pretty good job.
@@LowBuckGarage Ok, that was a pretty dum question now when you told me🙈
Thanks for answer👍
@@markuschampos5750 Not really, sometimes odd-ball equipment works in unusual ways. Always worth asking!
One word: Marvel Mysterie oil!
Always use MMO when a piston is stucked!
Where in the H-E double tooth picks do you find these motors with all the water in them? At the bottom of a swamp?😛
I thought I was the only one that used the vacuum in that way.
Instead of the air hose.😊
Use marvel mystery oil in those cylinders.
What's in it? Nobody knows, it's a mystery.
I will look to see what kind of motor it is but my dad had a motor that was a airconpress motor. going to junk it any way ran but only pump 60 psi. gregg Logan
21:30 Great filming. Very cool and fun video 21:30
Thanks, glad you liked it!
Meatloaf timing😂😂😂😂
You ARE the man! 💪😂
Berryman chem-dip ..down around the pistons....
Great. Video thank you, question, what kind of starter did you use?
It was a ACDELCO 3361425, meant for a '83-92 Toyota Landcruiser.
@@LowBuckGarage ok, thank you very much, I have been enjoying your videos a lot, greetings from Ensenada, Mexico.
What made all those seize? I have cars sitting around everywhere....should I be turning the engines every ...so often....years?
Time and exposure. They had been sitting unused for well over 10 years each, some well over 20 years. Also bad storage, like being left without spark plugs (the #1 L-head), or left in the woods with an open carb (#1 F-head).
It is a good idea to spin motors over every few years, and use a fogging oil if you know you're going to let it sit for a long time. I'd try to move them every 5 years or so, depending on your climate. Surface rust will start forming in the cylinders a few years before it seizes, so when they're hard to turn over at first get some extra oil in the cylinders.
@@LowBuckGarage tHank you....I didn't realize...never had a seized engine...so never developed that instinct.
reminds me of "Ole Rube Goldberg" automotive service... :)
Amazing! Thanks.
I very much liked the compressor engine! I guess those heads are quite rare, now? Anyone using one of those?
Valve compressor win! Don’t tread on me! We can be friends 😉
What we really need is your meatloaf recipe to compare to Mama's... lol.
Thanks, very good.
Love it man, keep up the awesome work
Thanks, I appreciate it!
You got the clear oil change 😂😂😂😂
I like your style!
Thanks!
Did the same here in Australia.with VW motor
How is the diesel oil more like what the Willys engine was supposed to have?
15 busted blocks, nuts, studs..... it will be fine
you think that guy in the beginning had enough bass for his car?
Hey, great vids, any tips on unsticking valves in an l head jeep motor, when they are down flat to the block, and stuck in, possibly at the valve seat and the valve guide both? Thanks,
I usually let it soak for a while and work the cam lobe back and forth to lift it. You might be able to sneak a drift through the port and tap it upwards. That could destroy the valve if its really stuck, but valves are cheaper than replacing a cam.
When u fixing old car behind u in this video?
I had a camshaft break into 3 pieces. You beat my record
Add transmission/acetone mix to release frozen metal
What’s the difference between a f head motor and a l head motor?