PLEASE HELP : Hello Sr, firstly Thanks alot by your videos. please could you help to me? I have all configured for RTL with radio off fail safe, all check in the computer and also with my radio, all seems work well, but when I switch of the radio it does not apear the red big letters message in the meddle that says ( FAIL SAFE , NO RC Receiber ) altough it appear down below in the rigth corner the fly modes where the system advise that RTL mode is ON, I think it is working all, but I have fear to make my first fly because I dont see this big letters in red about FAIL SAFE , NO RC Receiber
First, check the THROTTLE FAILSAFE parameter in the full parameter list to confirm that it is enabled and set to the action RTL. Remove the propeller, arm your copter, keep the throttle in the middle position, then power off your RC. Check the HUD on the mission planner for the displayed message. Ensure that you have a strong GPS signal during this test.
How do we come out of Failsafe? The failsafe was triggered and the failsafe on the mission planner isn't going and when ever we connect MAV link the ESCs starts to beep like anything and the motors also starts to spin on their own!
@@karthikstechtime0910 i would have set the drone for some mission(waypoints) and due to some reason the drone isn't able to follow the path , then how to switch to manual mode so that i can take the control of it. Is it that we have to do using the switch provided or else can we program in such a way that if it fails , it will immediately give the control
so informative karthik bhai thank you, i have learn alot from this video
Thanks.
Good job, Karthik..
Super ji... Thanks for sharing...
Welcome..
Thanks for this instructive video! Did you try failsafe with rally points?
Yes, that video is also on my list. Please check it out.
PLEASE HELP :
Hello Sr, firstly Thanks alot by your videos. please could you help to me? I have all configured for RTL with radio off fail safe, all check in the computer and also with my radio, all seems work well, but when I switch of the radio it does not apear the red big letters message in the meddle that says ( FAIL SAFE , NO RC Receiber ) altough it appear down below in the rigth corner the fly modes where the system advise that RTL mode is ON, I think it is working all, but I have fear to make my first fly because I dont see this big letters in red about FAIL SAFE , NO RC Receiber
First, check the THROTTLE FAILSAFE parameter in the full parameter list to confirm that it is enabled and set to the action RTL. Remove the propeller, arm your copter, keep the throttle in the middle position, then power off your RC. Check the HUD on the mission planner for the displayed message. Ensure that you have a strong GPS signal during this test.
How do we come out of Failsafe? The failsafe was triggered and the failsafe on the mission planner isn't going and when ever we connect MAV link the ESCs starts to beep like anything and the motors also starts to spin on their own!
Could you please provide more details about the issue you encountered with ArduCopter?
hi karthik , in cube orange using holybro power module there is no sensing current value and percentage . how to fix this issue?
docs.holybro.com/power-module-and-pdb/power-module/digital-power-module-pm-setup
Hi, thanks by respond
I did all this previously of my message, but this red big words not appear
There are no concerns. Is everything functioning properly?
how to connect the controller to ardupilot for manual operation?
Could you explain in detail?
@@karthikstechtime0910 i would have set the drone for some mission(waypoints) and due to some reason the drone isn't able to follow the path , then how to switch to manual mode so that i can take the control of it. Is it that we have to do using the switch provided or else can we program in such a way that if it fails , it will immediately give the control
@user-eh4gq4er5z You can cancel while flying in auto mode by flipping your mode switch twice (stabilize or althold or loiter)
@@karthikstechtime0910 oh ok, thank you ☺
hi this is harish iam building apm2.8 drone and iam facing issues in that how can i contact u sir?
karthikaeromodeller@gmail.com