How to Test the Water Valve on your Washer - Not Filling or Overfilling
HTML-код
- Опубликовано: 31 июл 2024
- In this video I show you how to test the water valve on your washing machine. If you are having issues with the washer not filling or overfilling the water valve may be defective and need replaced.
Here is the video on testing the pressure switch that I refer to in the video.
• How to Test the Pressu...
This troubleshooting process will work on most brands and makes of washers. The machine used in this video in an Amana Washer.
Whirlpool / Kenmore machines have the same setup as this one does.
The water valve on washers is sometimes referred to as the inlet valve or maybe even the water solenoid.
Here is a link so you can purchase a water valve for your washer if you need one.
amzn.to/1Lrx4rO
If you are not Subscribed to my RUclips Channel, make sure you do that now.
If you want to follow me on Twitter you can find me at applianceguy101
Thanks for Watching 
Хобби
You are wonderful! Your tip about cleaning the filter screen saved me the price of a new washer. Ecstatic, empowered 70+ female homeowner.
Yay for you! I'm also 70+ female, widowed, and RUclips is my best handyman!
Thank you sooo much. My basement was flooded from the Performa top load washing machine. After watching your video I was able to fix it. The hose was damaged and clogged. I just blew some air in the hose and replaced the damaged piece of hose. We are back in action again. Your the best.
Thanks for the troubleshooting walk through! Appreciate the way you covered both the big picture and the critical details.
Hi I work for a major Restaurent Company and because of this Video I was able to fix therte washer. So thank you very much.
Saved me time and money. It overflowed and wouldn’t stop even when unplugged and we didn’t know what part to replace till we found your video. Thanks so very much! And part on Amazon was $15.00. (We found some on different sites, $75.00. ) And we installed ourselves in short amount of time.
Live on the beach & constantly fight red ard water scale on everything. Washer won't fill today hoping that's the E-Z fix. Thank u!!! it's so nice to not have to call a man for help especially a repairman. Much gratitude from a single mom on a budget bc I have a toddler w a complex medical case who recently had a liver transplant. It feels good to have control over something in my chaotic life even if it's just my washing machine. Your karma basket is FULL Sir. MUCH 💝 from FL..
Great video! The very last thing you mentioned was what I needed to hear! If the water still flows when you unplug from wall-water inlet valve is bad! Exactly what my machine does!
Great video Bill! Thanks.
If the washer isn't filling and the pressure switch is fine and the washer valve/solenoid checks out as well, there is a fuse on some models between the pressure switch and the controller which may be the problem. Replace it with a 4amp quick blow fuse.
Nice video Bill. Your voice is relaxing and has calmed me down listening to you as you clearly and good direction in this repair job. Thank you
Excellent video Bill 🧐, I was experiencing the water inlet being clogged w/sediment
On a Whirlpool Commercial coin operated washer, removed both screens & cleaned up
Also had to replace the dogs in the agitator.
For the first time in 19 years,
and the machine still washes great.
Thanks Bill!
Thank you Bill. I showed this video to my husband and he said he suspected it could be this but you just confirmed his suspicion. Now he can order the part.
;)
Awesome video!!!.....used it step by step to troubleshoot and fix my 18 year old Whirlpool that was filling slowly on the cold water side.......replaced the water inlet valve assembly for about $28.00
73 dummies here! Keep these videos rolling brother! You are helping a lot of people who can’t afford new and can’t afford a repairman. Semper Fi!
Thank you Bill. You just saved me a ton of time and money.
Thank you so much, Bill! You helped me solve my issue of having no cold water, and saved me the price of a new washer or hiring a repair service. Thanks for breaking it all down and making it easy to understand.
Unfortunately Bill Pass.
Instablaster...
I cannot believe how many videos I am watching on washing machines ;=)
I have a Cabrio that has been a pain over the years. I replaced the drum hangers on it a few years back and 2 other repairs - a pump I had done and a control board. Now I have a LF error that seems to happen when I specify the load size or cycle. If I leave it be on Auto and medium, it works. My conundrum is I cannot decide on a new machine vs replacing the inlet valve and is it the valve or is this a control board sensor issue. 120.00 is not that much but if it is not the issue, it is a waste.
If I could choose a new machine, I'd just buy it but I'm not really enthused with any. Speed Queen seems to have controversy over its old/new models. Front loaders are a whole nother animal.
This was a nice video - thank you.
Thanks so much for the information. Tried the other possibilities and the water still ran free. I found your video and will be buying the valve tomorrow.The cold water runs whether the the machine is on or off.
Well done captain. You made my problem a simple one with this video. Thank you !
Awsome. Haven't tried it yet but as a young senior woman with no man to help you have made it clear that I can do it myself!!! Then I dare any of the guys to ask me again to do their laundry. LOL LOL
I like your videos. Your information is fairly comprehensive and the video is well made but even better, you don't treat us like idiots.
Good stuff my new friend. I hate buying new machines if it's a easy fix.🍻
Thanks for the clear and detailed explanation!
Good information and video bro. Thanks.
U are helping people save.because if u go and buy one it will cost u a lot just a little videos from u to fix the little things it needs is good.stuff just to high now.so I appreciate it because it's the truth.that wat mine are doin.i my need valve but it's simple.then goin and get another one I don't hv the money so if I can fix it.just by watching ur videos.know doubt.thanks again
Today's date is January 23rd and it is Saturday 2021 I'm leaving this comment to let you know whenever you see it thank you thank you thank you for sharing the knowledge you are truly a man of knowledge
Great demonstration Bill. Correction needs to be made in your description of the water fill circuit. Water level switch or Pressure switch, to the Water Temperature Selection switch, then inlet mixing water valve solenoids. Supply Water pressure forces the the valves closed. The electromagnetic force from the energized solenoids opens the valves. Spring and water pressure closes the valve diaphragm once electrical current stops.
Many of the manufacture service manuals no longer describe the function of the valve, just how to test, remove and replace the valve.
Sir, this comment really helped me out tonight. Thank you so much.
Great video. Thanks!
Very good video.
Very well explained.
Great video. Straight forward.
Thank you, so informative👍🏽
Very good information thanks bill
very helpfull thanks Bill !!!
you're awesome,Thanks bill ......... I manage to fix my washer ..without it costing me so much money :)
You are a great educator! Thanks. I tested a Whirlpool washer downstairs, and it worked fine. However when moving it upstairs into the laundry, it could not pass the rinse cycle. Bypassing the lid switch, even replacing the timer still could not fix the problem. My limited knowledge does not allow me to pinpoint the real cause. Would you please educate me on how to diagnose the problem and fix it? I will greatly appreciate your valuable instructions.
Hey Bill, I hope you check for comments.........My 28 yr old Amana is having issues. I bought it used a few years ago and the cold water just trickles in. This was with a new hose, new screens and we checked the water pressure......all that's fine. Because of where my washer sits, it's not easy to pull it out and tear into it, so without using a tester or tearing into it, I eliminated the inlet valve as the problem by swapping the cold and hot hoses at the hook ups, so the cold would run thru the hot side and vice versa. The cold trickled into the hot side. I only recently found it might be the timer. It has another issue too, but I'm on the fence about fix it or because of it's age, buy a new washer. It stops mid cycle and smoke comes up around the drum. I can let it rest an hour after it fills up and not do the extra large loads and it's fine. When it shuts down, it has to rest a few days and then it's fine! Is that also the timer?
Excellent info thanks man.
Thank you so much for this video!!🎉
Love your videos Bill ,Can you do a video on when the tub doesn't seat properly, I mean when the tub leans towards the back...Thanks
Thank you. Nice video, keep it up👌👍
Thanks! I will give it a shot. Pretty sure that is what it is, but it is nice to have a refresher.
Thank you so much for the informative video. The only thing I wish you would have included was how to open the cabinet. I have never worked on a washing machine that opened this way and it took me forever looking at parts diagrams and videos to figure it out! Of course the one I'm working on is branded magic chef and there are no videos showing this model.
Super nice videooo,thanks!!!
Very Helpful.
Thanks man very helpful
Verry informative !!!
good one, thanks...
We put down new flooring in our kitchen and since we put everything back our washer fills constantly, even after turning it off and unplugging. I had to turn the water off at the wall. I'm pretty sure we hooked the hot and cold up wrong (crossthreading?) So now I'm replacing this part and feel confident!
Big help thanks!
Thanks Sir. Good Instructions
Good video. My washer has intakes going horizontal instead of vertical also has plastic filters. Is that basically the same repair? If so how does the plastic filters come out unlike the mesh filter
great information Bill RIP
Love the video🙏
Good video cheers buddy!
Seriously, thank you sir for sharing the knowledge you save my washer and I greatly appreciate you as a human being 👍. There's a worldwide pandemic that's called covid-19 currently and it's hard to get someone to come out right now and even when they come out you never know if they have covid-19 only did you save my washer you may have saved my life thank you.
Thx Bill. Great video. How would I know if the control board is shot and I need to junk the whole washer?
Good video thank you!
great view!
awesome thanks for the video explain that perfect!!!!
videcon washing machine not working E5 display
Thank you so much.
I wonder if you could offer an opinion on this one. We have a 35 year old Kenmore/Whirlpool washer, a high end model that still runs perfectly except that it just buzzes for about one minute at the start of the initial fill cycle, and then fills normally for the rest of the cycle. There is little to no flow from the detergent/softener trays during the cycle. The back story is, this is a model that uses two valve units, an inlet/mixing valve with three solenoids, and a dispensing valve with three solenoids. The original valves didn’t fail until the machine was about 20 years old. Our repair man at the time installed both new FSP valves and it ran great again, but they both failed again just a few years later. Since then I’ve been buying new-old-stock valves on eBay (Whirlpool stopped making them about 10 years ago), and they work great for a few years and then fail. Why would they fail so frequently? Flow from the wall is good and the screens on the valves are mostly clear, though we do have very hard water. As best I can recall, the pressure switch is either very old or possibly original.
I’ve tested the resistance on the failed solenoids and they’re always around 900 Ohms, and the plungers with the iron cores move freely. Yet, putting in new valves fixes it. What am I missing?
Thanks for the information. Will be testing our washer. When I place the washer on a hot cycle it fills up with cool water but as soon as I turn off the cold water value to the washer where only the hot water can run in, the water is extremely hot. Have you ever heard of this?
thank you for the video
if the coil of vave is damaged the then the valve stay closed does this cause the controle board to cut of power ?
this is the symptom i have
when i power on the machine i heard the dor lock working then cut of
could this be a faulty valve? or pressure switch or control panel? on my lg wd 80130f
Thank you!
Great video, we live in Alabama and the
e build up from chemicals is terrible I I know that is it we replace water heater elements often thank you
Great info. I think your valve was clogged with a fly at 3:14. It flew in my ear...lol
Great video! How do I change the cool water solenoid?
hi Bill could you check the water inlet valve contacts for continuity? so if you check between the two contacts if it is open could that mean the coil is bad? thanks
I need to watch your pressure switch video. My washer is agitating as soon as I turn it on but not one drop of water comes out on the hot or cold side. I had the rubber line pop off the pressure switch one time that made the washer keep on filling till it overflowed onto the floor. I think the switch is probably stuck this time. Wont fill no matter how I play with the switch or turn the other one on hot or cold. Just want some more info before I attempt to fix it by replacing the pressure switch.
So my question is my washer washes and rinses the water out the first time second time it does not fill at all. I can hear it ticking waiting for the spin cycle but it never fills up again. I'm going to check the screens as you indicated on this video and I learned something new today hopefully that's the problem.
No water going in my old kenmore. When I set it, I notice the timer doesn't move either. How do I know if its the water valve or something else?
Nice video
I have a Kenmore elite Oasis. I run the diagnostic test that cycles thru each cycle. when I do the test it does fill up but when I want to wash it doesn't
Just wondering, my Maytag washing machine continues to fill even when power is off. I have had to turn the tap off to stop this, does this mean it is the water valve defective?
Hello thanks for you video but what is the problem if you don’t have 120 v to the valves
Hi.
I have a
GE front load model GFW450SSKOWW. It hums when you try to wash , hot and cold is doing the same thing.
hi Bill Newberry I'm having some trouble with my whirlpool washer ser.#(WTW4800XQ4) I'm trying to find out why it's not filling up properly may you help me out?
Helpful
Great videos Bill!
I’m having trouble with the washer filling. I checked pressure switch using your video, seems good. I am getting 120V on all solenoids (inlet valve) on all temp setting except the cold solenoids on cold-cold setting only. I can get the washer to fill on a warm setting however it will not refill automatically for the rinse cycle. We have to turn on/off the washer several times to have it start to fill. Any idea where I can turn next.
Same issue here with commercial wascomat any answers
My Kenmore 110 washer has a slow cold water drip into the tub when machine is off. When I try to run cold water only, flow is very light. Warm or hot, I get good water flow. From what I heard here, maybe my cold water screen is clogged, but then why the drip? Hope you can help - thank you.
what do you call that white and red plastic connect to the valve solenoid?
Hey Bill. I disconnected my cold line and I didn't see a screen. All I saw was like a small copper line in the center and a rubber gasket around it. I have a slow trickle on both.
My washer start filling then stop. Could it be the inlet valve? And also the Cold water switch has a crack in it. So you think that would stop it from filling? Thanks a bunch.
Question. I have an old kenmore washer. Model 110. 82870120
Kenmore 70series. Cold water won't stop running, even when unplugged, but hot water works normally. What would this be? Originally cold was only trickling, I took the screen out and lost it inside the washer, so there's no screen on the cold side right now. Caldwell water runs constantly.
hello bill..my name is azam n i from Malaysia. i hve sme question about my samsung 10kg top load washer which hve double water inlet valve..the question is, when at the rinse process, the softner is not taking out by the washer..for ur info, the water inlet valve is the new one..tq sir
Great video, very descriptive and informative. I now have the confidence to tackle this job. Thanks Bill!
Very helpful..i pull the plug and water still comes in...bad water valve thanks
Bill, when I place the meter on the cold water valve the agitator starts spinning. what's my next step?
Thanks
I have replaced the inlet valve twice in the last two months due to slow, slow cold water fill. Any idea why it would be going bad. After replacement it works fine for a couple weeks and than slow cold fill again
Bill what if your washer is only filling half way? and also sometimes only gives cold water no hot. It sounds like the inlet valve what do you think. Thank you.
can I test the valve while its connected to the washer on a maytag bravos xl mvwb750??
Guess i should of watched this video before asking a question on your last video. If the pressure switch and inlet valves test good, what would be the next step? Samsung front load washer....
Hi Bill:
Just checked my kenmore washer water valve. No hot water. When I turn on I hear a hum, voltage is 120v but no hot water. Does humming sound mean solenoid is ok.? Does valve need to be replaced or is problem coming from somewhere else. The cold water side is ok. I would appreciate a reply. Rb
My portable washer, the cold works fine. When I try to use hot it takes a moment to works, fill for 10-20seconds then stops and does nothing . Is this a problem. With the inlet or pressure?
Anyway to test run this same machine while opened up like this? I have a leak and can’t seem to find it and want to test run while open. I have replaced drain pump and still got a leak up front. Taking cabinet on and off is just not very doable where I’m at.
Question from Kansas. GWL15 wouldn't drain. Back story...I replaced the diverter, pump and drum bearings 6 months ago. All worked fine until last week when it wouldn't drain. Removed the diverter for inspection and reinstalled. Removed the pump and cover in tub, it was clean. Started new washer....it stopped. Discovered the bay below electronic panel was full of water and fried the board. H/C water valve bad? Strange all this happened after my inspection
Comments appreciated. Rick
So on my whirlpool wtw4816fw2, it starts filling and the water goes straight out the drain hose. Obviously the valve is stuck open. I put the selector on cold and checked both sides of the valve. The cold has 120 and the hot ZERO. I put the selector on hot and the same thing. Why could I not be getting voltage to the hot side? Is the control board fried or does this have to do with the water temp selector switch (dial)? Thx Bill
What about not mixing water for warm water? I can switch to cold its ok, hot the same way but switch to warm it is cold.
Hi Bill, I have an older Whirlpool top load washer that is not dispensing hot water. Cold is fine. I replaced the inlet valve, swapped out the hoses, checked for corrosion but it still not giving hot. I turned off cold and left hot on and still no hot water. Any assistance would be appreciated!
can you test for continuity on valve terminals also?
The solonoid casing on my cold water valve has cracked and I plan on ordering a replacement. Is there a safe way to test if the lead wires are still supplying voltage to the solonoid? I'm worried about spending money on a part just to find that the power supply has been damaged.
Is there a way to check this stuff without taking the entire front off of the machine. I'm writing in a vey small space.