Tom, Thanks for taking the time to explain the installation so that all can understand. Checking availability to purchase sherpa. RC guy for 40yrs, still learning, Thanks Tom USA
@@PhilBrindley the blue mate. I showed the Wife the sherpa. She said blue one nice... Boom 💥 pressed the trigger straight away. 😂 😂 😂 😂 Don't normally get a second chance like that😂 😂
Great videos ;) im almost new to Crawlers.... and got a Amewi Pro like the Absima Sherpa... almost same hardware setup... I also got a Absima Sherpa... but is it possible to get a DIG gerabox that can be activatede then u climping rocks to awoid the truck to tilt back over.. sorry for my english...
Hi and welcome. I've not seen a DIG available anywhere for the Sherpa so far. I'm also not sure it would help with climbing as you would be having to drag the rear wheels up the climb and this would just cause the tyres to grip and the front to lose traction. The best option to improve the climbing ability in my opinion is to improve grip (better tyres) and get the centre of gravity as low and far forward as you can. The Sherpa body is a little top/rear heavy and this is made worse by putting things on the roof rack. You can either counter this by removing weight from the upper rear, or adding weight to the lower front (unsprung weight preferably). You could also try using lighter shock oil in the front and heavier in the rear. Ultimately though, the Sherpa is a trail truck that crawls quite well, rather than a crawler than does ok on trails. Hope that makes sense. 🤙
Hi I watch all your videos and thank you because it helped me a lot. I have a problem with my SHERPA. The magnetic body support at the front is not effective during a fall or rollover. Would you have an effective solution to remedy this. thank you for your help
Hi Kevan, thanks for watching, I'm really glad that the videos have been helpful. I had the same problem with the body coming open. Originally I went with a 3D printed clip that fixed under the body and clipped to the chassis (see episode 1). This worked OK, but I found that the body would still open in a bad roll. Since then I have resorted to using traditional body posts and clips, but not in the usual place. They are on the wheel arches and clip through from underneath the wheel arch liner and through the main wheel arch. I 3D printed the posts (of course, but you could modify normal ones) and used the Arrma body clips that have the rubber tags on them to attach them to the body. It's hard to explain, but if you skip to 03:55 in this video you can see the posts sticking up through the wheel arch liner. If I can I'll do a quick video about it later, but if not then I'll include it in this weeks main video. Hope that helps... 🤙
Bonjour, Votre vidéo est très bien , le moteur est il d'origine. J'ai installé sur mon sherpa un hobbywing 1080, je ferai une comparaison avec vos réglages et les miens . Je vous félicite des autres vidéos que vous avez réalisé. Le mien et de couleurs orange. Je suis inscrit sur un forum français, le nom RC découverte. Vous pouvez aller voir les passionnés comme vous et moi....😁👍
Merci. Le moteur est standard dans mon Sherpa. J'ai eu un Holmes Hobbies Crawlmaster Sport pendant un moment, ce qui était très bien, mais je l'ai retiré maintenant pour l'utiliser dans un autre camion. Je n'utilise pas vraiment beaucoup les forums ces jours-ci, mais je devrais vraiment les consulter davantage car ils regorgent d'informations utiles. 🤙
Absolutely brilliant vids Phil! Hope you haven't finished your mods on this crawler. Was hoping to see someone, somewhere installing the Hobbywing Quicrun Fusion 2-in-1 in this crawler. Several of the guys on FB have done it, but no vids! Looks like a tight squeeze 😞
Thank you, glad you enjoyed them. I've done a bit to this rig since (check out the recent Makeover videos) but not installed a fusion yet. I have one in my Element Ecto and it is a fantastic motor. I can see that it would be tight, but the fusion is supposed to fit where a 550 can motor will, and the wires come out of the side so I think it would go in ok. Thanks for watching. 🤙
Hey Phil! Thanks for your Awsome videos on Sherpa! In the video you complain about the drag brake and reverse, but normally that's a easily programmable thing on Crawler ESC's... There's no way to you to change that instead of put a new one? or you just went for the upgrade and problem solution in one shot? Thanks in advance
Hi Ivo, I don't think there are any other settings on the Hobbywing 1060 (the one in the stock Sherpa) that you can change other than running mode and battery type. Hence why I changed it out. Having driven it more since, I now think that they drag brake strength is the same in both ESCs, but I am working it harder now as I am tackling harder climbs and descents. But I am certainly happy that I can now alter how fast that brake applies, allows for much smoother driving. Thanks for watching 🤙
@@PhilBrindley oh... That's a downside of the truck, I thought that you couldn't change the settings because it came off without the programme card. Well, thank you very much for the feedback!
Excellent video again thanks greets from the Netherlands 🇳🇱
Thank you. 🤙
Tom, Thanks for taking the time to explain the installation so that all can understand. Checking availability to purchase sherpa. RC guy for 40yrs, still learning, Thanks Tom USA
Thanks for watching and taking the time to write such a nice comment. 🤩🤙
What a great series with so much good info. The Sherpa looks cool! We should get some chase shots with the Betafpv 95Xs
Thanks mate. YES! We absolutely should, EPIC Cinematic mountain footage, in 1:10th scale. That has got to be worth a go! Roll on April! 🤙
just bought one .
Great bit of kit mate. Enjoy.
Brilliant info and build up of the esc Phil. 👍 🇬🇧😃👌
Thank you Gaz. 😁🤙 What colour did you go for?
@@PhilBrindley the blue mate. I showed the Wife the sherpa. She said blue one nice... Boom 💥 pressed the trigger straight away. 😂 😂 😂 😂 Don't normally get a second chance like that😂 😂
@@gazfpv HAHA! Brilliant!
Great video mate. 👍
Thanks Rich 😁🤙
cool vid! appreciate the views number! keep it up! big like! 👍👍👍
Thanks, will do! 🤙
Great videos ;) im almost new to Crawlers.... and got a Amewi Pro like the Absima Sherpa... almost same hardware setup... I also got a Absima Sherpa... but is it possible to get a DIG gerabox that can be activatede then u climping rocks to awoid the truck to tilt back over.. sorry for my english...
Hi and welcome. I've not seen a DIG available anywhere for the Sherpa so far. I'm also not sure it would help with climbing as you would be having to drag the rear wheels up the climb and this would just cause the tyres to grip and the front to lose traction. The best option to improve the climbing ability in my opinion is to improve grip (better tyres) and get the centre of gravity as low and far forward as you can. The Sherpa body is a little top/rear heavy and this is made worse by putting things on the roof rack. You can either counter this by removing weight from the upper rear, or adding weight to the lower front (unsprung weight preferably). You could also try using lighter shock oil in the front and heavier in the rear. Ultimately though, the Sherpa is a trail truck that crawls quite well, rather than a crawler than does ok on trails. Hope that makes sense. 🤙
I know I'm kinda randomly asking but do anybody know of a good place to stream new movies online ?
Hi
I watch all your videos and thank you because it helped me a lot.
I have a problem with my SHERPA.
The magnetic body support at the front is not effective during a fall or rollover.
Would you have an effective solution to remedy this.
thank you for your help
Hi Kevan, thanks for watching, I'm really glad that the videos have been helpful. I had the same problem with the body coming open. Originally I went with a 3D printed clip that fixed under the body and clipped to the chassis (see episode 1). This worked OK, but I found that the body would still open in a bad roll. Since then I have resorted to using traditional body posts and clips, but not in the usual place. They are on the wheel arches and clip through from underneath the wheel arch liner and through the main wheel arch. I 3D printed the posts (of course, but you could modify normal ones) and used the Arrma body clips that have the rubber tags on them to attach them to the body. It's hard to explain, but if you skip to 03:55 in this video you can see the posts sticking up through the wheel arch liner. If I can I'll do a quick video about it later, but if not then I'll include it in this weeks main video. Hope that helps... 🤙
@@PhilBrindley ok thank you for your explanation.
I can't wait to see your video on this.
Thanks again and keep making videos on SHERPA
I’ve used Velcro on the wheel wells and works great 👍🏻👍🏻
Bonjour,
Votre vidéo est très bien , le moteur est il d'origine. J'ai installé sur mon sherpa un hobbywing 1080, je ferai une comparaison avec vos réglages et les miens . Je vous félicite des autres vidéos que vous avez réalisé.
Le mien et de couleurs orange.
Je suis inscrit sur un forum français, le nom RC découverte. Vous pouvez aller voir les passionnés comme vous et moi....😁👍
Merci. Le moteur est standard dans mon Sherpa. J'ai eu un Holmes Hobbies Crawlmaster Sport pendant un moment, ce qui était très bien, mais je l'ai retiré maintenant pour l'utiliser dans un autre camion. Je n'utilise pas vraiment beaucoup les forums ces jours-ci, mais je devrais vraiment les consulter davantage car ils regorgent d'informations utiles. 🤙
Absolutely brilliant vids Phil! Hope you haven't finished your mods on this crawler. Was hoping to see someone, somewhere installing the Hobbywing Quicrun Fusion 2-in-1 in this crawler. Several of the guys on FB have done it, but no vids! Looks like a tight squeeze 😞
Thank you, glad you enjoyed them. I've done a bit to this rig since (check out the recent Makeover videos) but not installed a fusion yet. I have one in my Element Ecto and it is a fantastic motor. I can see that it would be tight, but the fusion is supposed to fit where a 550 can motor will, and the wires come out of the side so I think it would go in ok.
Thanks for watching. 🤙
@@PhilBrindley Thanks mate. Fantastic advice, as always! Just watching your ISDT review pt2 ;-)
Anytime 🤙
Hey Phil! Thanks for your Awsome videos on Sherpa! In the video you complain about the drag brake and reverse, but normally that's a easily programmable thing on Crawler ESC's... There's no way to you to change that instead of put a new one? or you just went for the upgrade and problem solution in one shot?
Thanks in advance
Hi Ivo, I don't think there are any other settings on the Hobbywing 1060 (the one in the stock Sherpa) that you can change other than running mode and battery type. Hence why I changed it out. Having driven it more since, I now think that they drag brake strength is the same in both ESCs, but I am working it harder now as I am tackling harder climbs and descents. But I am certainly happy that I can now alter how fast that brake applies, allows for much smoother driving.
Thanks for watching 🤙
@@PhilBrindley oh... That's a downside of the truck, I thought that you couldn't change the settings because it came off without the programme card. Well, thank you very much for the feedback!
Hi Phil
I just installed the HOBBYWING 1080.
Can you give me all the settings from ITEM 1 to 15 of your hobbywing?
thank you for your help
Hi Kevan.
1 = 3
2 = 1
3 = 3
4 = 3
5 = 4
6 = 2
7 = 9
8 = 5
9 = 9
10 = 4
11 = 4
12 = 5
13 = 4
14 = 1
15 = 2
Enjoy. 🤙
@@PhilBrindley perfecto my friend
Does anyone know how did he changed the front lights ?
Hi, which lights do you mean?
How has the absima Sherpa held up
Hi, it held up pretty well. I've not driven it for a while but I've not had any issues so far. Still going strong and nothing has broken.
@@PhilBrindley that's great to here. I'm on the verge of hitting the buy button.thank u
I'm using a tqi radio on my trx6 with a 1080 and it's just flashing red any advice thanks Joe
Have you completed all of the calibration steps?
@@PhilBrindley I called hobbytown we worked it out channel 2 is bad on my receiver thank brother
@@rcjoe406 cool glad you got it sorted. 🤙
@@PhilBrindley ya it was driving me nuts only wasted 5 hrs of my time lol