You're awesome!!! saved my Dremel !!!! That exact same issue with the stator. Just one tip for anyone with the same problem as me: depending on which of the two loose contacts is the problem, you may not be able to unwind a single turn to reconnect the wire. Just solder a stub of wire in case you have the issue on the wrong end of the coil (you won't be able to unwind it).
I wish I had read this comment before trying to unroll the inner thread, I cut it trying, but noticed that on the other side the innermost turn was slightly separated from the others, I pulled it and bingo! It was precisely the strand that had been cut, I think from factory leaves that strand separated to indicate that it is the first round.
Good morning, friend I am Brazilian living in Portugal I have a Dremel 3000 with little use today I was using it and it stopped working, I contacted the assistance and I was informed that I would spend about $ 60.00, I went to do a search on the yotube and found his video thank you very much and congratulations I managed to fix my dremel without difficulty and without spending any money thanks. Sorry the English translator kkk
Followed exactly your video, the problem was as you said, in the stator circuit. Trimmed the wire and put it back, now it's working again. I would never have figured it out on my own. Thanks very much, you have saved me time and money.
Also, thanks from myself. My Dremel 3000 failed last week. Followed your dis-assembly procedure and diagnostics and found the exact same problem! It's now working fine. Excellent work.
Thank you, thank you, thank you! … exact same problem with my Dremel 3000, fixed it using your easy instructions! … it must be the Achilles heels of the 3000 series. But what an easy fix, cheers again!
This repair works!!! Thank you for posting the vid, I have been searching long for a solution and this was the only repair that worked. Thanks a million!!!
Mine didn't work anymore about one month ago. As the stator winding had an on/off broken wire I thought it was something on the small circuit board, or the switch. Couldn't find anything wrong. Today I saw your video and checked the Dremel again. It's back in operation. Thanks a lot! :)
Brilliant video. We watched a different video with similar instructions but less detailed and we nearly gave up after trying to reattach the wires and still no luck. Its only through this video that we found out the previous fix hadn't worked because of the layer over the wire that needed to be scraped off. Thankyou!
Gracias, acabo reparar el de mi hijo en 10 minutos. Muchas gracias. Thanks. Less than 10 minutes and I have repared muy son's DREMEL 3000. Many thanks from Buenos Aires, Argentina
You made my day!!! In my case, the broken wire came from the core of the winding (the 1st turn) so I couldn't unwind one turn. Instead, I managed to un-enamel the last millimeters and soldered a bare wire. A warm hug from Argentina!
Off-topic: I feel empathy towards electronic components! I suffer when I see them suffer. So, when I saw you applying 9 volts to a white LED I felt my heart was about to explode! ;-) Please don't do that for a long time without a series resistor (from my own experience...)
@@watusilifestyle9335 Perdón, recién veo tu pregunta. En mi caso, tras cortarse en esa horqueta que hace la conexión, el alambre quedaba corto, y no podía desenrollar 1 vuelta porque venía desde abajo del bobinado, y tampoco podía estirarlo. Pero no es que lo había perdido. No me digas que se te cortó justo donde sale del bobinado! Si es así, más vale que sea en el final, no en el principio, o tendrás que desbobinar todo.
Thank you! You saved me time and money. I was able to determine that I had a bad stator. I not able to repair it but I did find a replacement part. My Demel 395 has lasted through 25 years of abuse. Made in the USA and well worth repairing.
Acabo de seguir tu tutorial con mi Dremel 3000 que dejó de funcionar cuando lo utilizaba como router. No sabes cuánto te agradezco que compartieras cómo componerlo, sólo me tomó 15 minutos después de ver tu video y ya está de vuelta trabajando. MUCHAS GRACIAS.
Thanks for this. It was the first Dremel repair video I looked at and showed exactly the problem I had with mine; broken connection in the stator coil. From reading the comments here it seems like a common issue. Thanks again.
Not an electronic whizz by any means. This is my second 3000, the first one went the same way without a whole lot of use, but as it was for work I put it a new one through my business. When this one stopped in exactly the same way I thought I'd look at the You Tube oracle as I was hacked off with using this similarly infrequently. As the last poster said, I cannot believe i've fixed it. turned it on and expected a spark but was 'shocked' but in a good way. Thanks so much for the step by step.
I watched this and found out how to take it apart. Found out my problem was tons of dog hair and nail dust! Blew it all out and worked like new! My wife is a dog groomer. You have to open it up to get it all out to make it work. This is definitely another possibility. Thanks for the video!
Thank you for the video ..After 2years lying in the toolbox not working, and me wanting to throw it away , it,s working again , all the time i thought it was the speed controller broken .
THANK YOU THANK YOU THANK YOU!😃 Even a Dis-Electric as myself could fix his machine 👍🏼 (I usually HATE video tutorials. Yours is JUST RIGHT! 😊👍🏼) stefan in Germany
apparently I'm the only one whose stator wire simply will not so easily be soldered. I've basically unwound the entire thing trying to find the lost wire for continuity. This video is still one of the best ones - but I wish someone had covered that part. though I don't think there's any smoking guns here. Don't lose track of the broken wire. It's hard to do. but I found a way haha
Thanks! It will be exiting to see if my Dremel suffer from the same problem. It just stopped. And it haven’t been used many hours. So strange that Dremel don’t fix this issue.
Yes, one pays a premium, sure the build quality is excellent but to what use if the thing stops working for no apparent reason! One can buy 3-4 cheap Chinese variants for the price of a Dremmel.
continuity check failed for one of the stator coils, wire looked ok, i pulled a little harder and it came off, unwinded 1 turn and clipped back, working back again seriously, continuity check is a must, thos little metal clips can cut the wire and keep it in place, so visul check won't do. thanks for the video, my dremel is back to work now
Mine had the exact same fault after fairly light use, I repaired it the exact same way and now it works again. Thanks Young DIY. Bad design Dremel....!
right on. Thanks. Just a video editing tip, when the camera is close up on something and is less sharp, slow down the speed frames so we can follow the details better.
Mine shut down suddenly, managed to open it after some struggling realising the stickers hold the half's together! =) Had I seen this I would saved a few minutes, what ever I checked the bearings and disassembled it as you did, had continuity over the coils, checked with multimeter. Suspected the component near where the cord attaches but saw nothing. Decided it wouldn't hurt to clean up the rotor where the coals touch since it was black, after few minutes with fine sandpaper it had a nice copper shine again, reassembled and to my surprise the damn thing was a alive again! One more thing I did was to spray contact spray in the power lever. Not sure what finally fixed it. Well constructed otherwise, easy to open and service if needed. Might open a cheap "Dremmel clone" just for comparison. :) Thanks for posting the video!
Thanks for the video. I'm having trouble freeing up the wire, as it's trapped under the coil. If I pull it too hard, the wire breaks. Any idea how I can get around this? Thanks
A minha parou de funcionar e desaparafusei toda, retirei os carvões, e acabo de ver no vídeo que faltou o adesivo...rs... não quis cortar, descolar, achando que não abrira por faltar algo... o vídeo é espetacular. Obrigado!
Four years later u r still helping people. Thanks man.
3 years after this video was uploaded, i just fixed my dremel by following your instructions, thanks man!
Saved me a lot of money here, my old 3000 is alive again! thanks
You're awesome!!! saved my Dremel !!!! That exact same issue with the stator.
Just one tip for anyone with the same problem as me: depending on which of the two loose contacts is the problem, you may not be able to unwind a single turn to reconnect the wire. Just solder a stub of wire in case you have the issue on the wrong end of the coil (you won't be able to unwind it).
I wish I had read this comment before trying to unroll the inner thread, I cut it trying, but noticed that on the other side the innermost turn was slightly separated from the others, I pulled it and bingo! It was precisely the strand that had been cut, I think from factory leaves that strand separated to indicate that it is the first round.
What thickness wire did you use?
Good morning, friend I am Brazilian living in Portugal I have a Dremel 3000 with little use today I was using it and it stopped working, I contacted the assistance and I was informed that I would spend about $ 60.00, I went to do a search on the yotube and found his video thank you very much and congratulations I managed to fix my dremel without difficulty and without spending any money thanks. Sorry the English translator kkk
Followed exactly your video, the problem was as you said, in the stator circuit. Trimmed the wire and put it back, now it's working again. I would never have figured it out on my own. Thanks very much, you have saved me time and money.
My Dremel 3000 failed with exactly that problem about a month after the warranty expired. Thanks for showing me how to fix it!
Yep, mine went pop just now, saw this video and yes, mine had snapped a coil wire as well, now fixed, very easy to do. THANK YOU you saved me £60 🥰
Also, thanks from myself. My Dremel 3000 failed last week. Followed your dis-assembly procedure and diagnostics and found the exact same problem! It's now working fine. Excellent work.
Great video. Very informative without any blah blah blah stories and stuff. I like how you made the continuity tester as well, ingenious!
Thanks a lot! That's the last thing I would've thought of. I was already going to order a new power switch when I stumbled upon your video.
Thank you, thank you, thank you! … exact same problem with my Dremel 3000, fixed it using your easy instructions! … it must be the Achilles heels of the 3000 series. But what an easy fix, cheers again!
This repair works!!! Thank you for posting the vid, I have been searching long for a solution and this was the only repair that worked. Thanks a million!!!
Mine didn't work anymore about one month ago. As the stator winding had an on/off broken wire I thought it was something on the small circuit board, or the switch. Couldn't find anything wrong. Today I saw your video and checked the Dremel again. It's back in operation. Thanks a lot! :)
Thank you so much for this. My dremel stoped and I fixed it right away with your instructions.
Well done! I will try and fix mine now as Dremel said too old to repair
Wonderful stuff, exactly what the Dremel needed! Thank you!
OMG this video has saved my Dremel, thank you so much!!!
Brilliant video. We watched a different video with similar instructions but less detailed and we nearly gave up after trying to reattach the wires and still no luck. Its only through this video that we found out the previous fix hadn't worked because of the layer over the wire that needed to be scraped off. Thankyou!
Thank you , 10 mins and mine is now fixed. Long live the dremel 3000 !
Gracias, acabo reparar el de mi hijo en 10 minutos. Muchas gracias.
Thanks. Less than 10 minutes and I have repared muy son's DREMEL 3000. Many thanks from Buenos Aires, Argentina
Excellent video - and it worked! Dremel is alive again!
Yep, broken wire, now all fixed. Thanks for putting up the video. Perfect 🙌
You made my day!!! In my case, the broken wire came from the core of the winding (the 1st turn) so I couldn't unwind one turn. Instead, I managed to un-enamel the last millimeters and soldered a bare wire. A warm hug from Argentina!
Off-topic: I feel empathy towards electronic components! I suffer when I see them suffer. So, when I saw you applying 9 volts to a white LED I felt my heart was about to explode! ;-) Please don't do that for a long time without a series resistor (from my own experience...)
Hola, a mi me paso lo mismo me parece. cuando le estaba sacando una vuelta se me corto el hilo de cobre. Como lo solucionaste??
@@danielrperez5778 - It's a BIG Coil Wire Gauge. He's only using it to complete a circuit... It won't harm anything!
@@watusilifestyle9335 Perdón, recién veo tu pregunta. En mi caso, tras cortarse en esa horqueta que hace la conexión, el alambre quedaba corto, y no podía desenrollar 1 vuelta porque venía desde abajo del bobinado, y tampoco podía estirarlo. Pero no es que lo había perdido. No me digas que se te cortó justo donde sale del bobinado! Si es así, más vale que sea en el final, no en el principio, o tendrás que desbobinar todo.
Fixed my Dremel thank you, evidently it is a weak point common to this model
Thank you! You saved me time and money. I was able to determine that I had a bad stator. I not able to repair it but I did find a replacement part. My Demel 395 has lasted through 25 years of abuse. Made in the USA and well worth repairing.
A well thought out description of all shown parts . Fixed mine , thanks again . Keith.
Had exactly the same problem with my Dremel 3000. Excellent instructions!
Acabo de seguir tu tutorial con mi Dremel 3000 que dejó de funcionar cuando lo utilizaba como router. No sabes cuánto te agradezco que compartieras cómo componerlo, sólo me tomó 15 minutos después de ver tu video y ya está de vuelta trabajando. MUCHAS GRACIAS.
Thank you, problem found (armature wire off and visual) and Dremel running again, saved me a fair amount of money.
Thanks for this. It was the first Dremel repair video I looked at and showed exactly the problem I had with mine; broken connection in the stator coil.
From reading the comments here it seems like a common issue.
Thanks again.
Solved, thanks! Greetings from Argentina.
Not an electronic whizz by any means. This is my second 3000, the first one went the same way without a whole lot of use, but as it was for work I put it a new one through my business. When this one stopped in exactly the same way I thought I'd look at the You Tube oracle as I was hacked off with using this similarly infrequently. As the last poster said, I cannot believe i've fixed it. turned it on and expected a spark but was 'shocked' but in a good way. Thanks so much for the step by step.
I can't nelieve i just fixed my Dremel....shaft was stuck but motor wanted to turn. Your video still helped...yay
Thank you for this fantastic DIY! You just saved me a ton of time and money!
Thank You for making this video, You make so simple that everyone can follow. I just repaired mines and it's working fine. Thank Again.
Thanks, I was able repair my handy dandy Dremel .... and saved money by not buying a new one
Exactly the same fault on mine. Good save. Cheers.
Thanks so much!
finally after years I have my working dremel again
infinitely thank you
Thank you so much! Now I won't have to travel really far and pay an exorbitant fee to get it fixed. My Dremel works again.
Thank you very much for making this video! This video helped me fixing my Dremel!
Awsome, Thank you Dude. Greetings from Turkey.
I watched this and found out how to take it apart. Found out my problem was tons of dog hair and nail dust! Blew it all out and worked like new! My wife is a dog groomer. You have to open it up to get it all out to make it work. This is definitely another possibility. Thanks for the video!
Had the same Problem with a dremel 300, European model.
This Video helped alot!
Thanks !
thanks to your video I was able to solve my problem. thanks!!
Grazie a questo tutorial sono riuscito a riparare il mio amato dremel 3000 grande!
The internals are very different from my 3000 that I recently purchased. Very good video.
Simple and very explanatory video, solved my problem, thank you my friend, a hug here from Brazil!
Excellent, repaired my Dremel 3000
The video was awesome, fixed it perfectly! Many thanks
Thank you for the video ..After 2years lying in the toolbox not working, and me wanting to throw it away , it,s working again , all the time i thought it was the speed controller broken .
Dude! Thanks for this video. The bulb test was a great tip
Awesome fix. Worked brilliantly. Thanks!
Whooooo. My dremel works again! Thanks!
Epic video, saved my day. I can’t thank you enough 🙏
This video saved me a lot of time, money, and headache, thank you so much for posting! :-)
Thank you for your video! My Dremel 3000 had exactly the same problem.
THANK YOU THANK YOU THANK YOU!😃
Even a Dis-Electric as myself could fix his machine 👍🏼
(I usually HATE video tutorials. Yours is JUST RIGHT! 😊👍🏼)
stefan in Germany
apparently I'm the only one whose stator wire simply will not so easily be soldered. I've basically unwound the entire thing trying to find the lost wire for continuity. This video is still one of the best ones - but I wish someone had covered that part. though I don't think there's any smoking guns here. Don't lose track of the broken wire. It's hard to do. but I found a way haha
Great video, explains really well
You saved my Dremel, thank you.
Watching your video I solved my problem. Tks!!
Very thorough and clear..just have to take mine apart😁👍
Thanks! It will be exiting to see if my Dremel suffer from the same problem. It just stopped. And it haven’t been used many hours. So strange that Dremel don’t fix this issue.
Yes, one pays a premium, sure the build quality is excellent but to what use if the thing stops working for no apparent reason! One can buy 3-4 cheap Chinese variants for the price of a Dremmel.
continuity check failed for one of the stator coils, wire looked ok, i pulled a little harder and it came off, unwinded 1 turn and clipped back, working back again
seriously, continuity check is a must, thos little metal clips can cut the wire and keep it in place, so visul check won't do.
thanks for the video, my dremel is back to work now
Mine had the exact same fault after fairly light use, I repaired it the exact same way and now it works again. Thanks Young DIY. Bad design Dremel....!
Thanks bro.
Thank you, thank you, thank you. That was it. My Dremel lives again.
I was just about to buy a Dremel 4000 because my 3000 has some issues!, I'll be taking it apart this weekend
thank you for the video it saved my dremel
just repaired mine! Thank you.
solved the same problem, saved my xmas presents, thx!
Thanks so much! You saved my Dremel!
thanks a lot. Same trouble (coil broken), solved thanks to your guide !!!!
thanks for your lesson it was great it was so easy for use to understand the way you specify l like
Thank you for posting this video, i just fixed mine because of this. Good job, Man!
Super...Thanks from Turkey. My problem is fixed.
Thanks for this, had the exact same problem, solved in 10min.
thank you for this video. I was able to fix my 3000 using the intel
Exatamente o problema da minha. Vídeo caiu como uma luva! Obrigado.
right on. Thanks. Just a video editing tip, when the camera is close up on something and is less sharp, slow down the speed frames so we can follow the details better.
Nice video! Other videos on this tool address only the brushes. This one might actually deal with the problem affecting my own Dremmel. Thanks!
burned dremel problem fixed! thanks bro!
Mine shut down suddenly, managed to open it after some struggling realising the stickers hold the half's together! =) Had I seen this I would saved a few minutes, what ever I checked the bearings and disassembled it as you did, had continuity over the coils, checked with multimeter. Suspected the component near where the cord attaches but saw nothing.
Decided it wouldn't hurt to clean up the rotor where the coals touch since it was black, after few minutes with fine sandpaper it had a nice copper shine again, reassembled and to my surprise the damn thing was a alive again! One more thing I did was to spray contact spray in the power lever. Not sure what finally fixed it.
Well constructed otherwise, easy to open and service if needed. Might open a cheap "Dremmel clone" just for comparison. :) Thanks for posting the video!
Nice work!!!
Thanks for this tip. Fixed mine exactly like showed on the video. Wish you the best! :)
Awesome, thank you, saved another dremel good man!
Sir can we check continuity with multimeter instead of battery?
Brilliant thanks for the video just did that and fixed my dremel
Thanks for the video. I'm having trouble freeing up the wire, as it's trapped under the coil. If I pull it too hard, the wire breaks. Any idea how I can get around this? Thanks
It was very helpful, my Dremel works again, thank you!
Thanks fr watching bro.
Thanks for the tips.. my dreamel bearing needs to replace but I don't have puller to remove it🤔
Yep, had same problem, fixed now. Many thanks
thank you. you saved my Dremel
Muito obrigado, não sabia o que fazer, já estava pensando que iria por a dremel no lixo, foi salva pela sua ajuda. Obrigado.
This was so helpful!! Thank you thank you!!
thanks a lot!
i managed to fix my 3000 by soldering a loose contact at the coil.
i was about to throw the thing away.
If there is no problem in the stator coil, which part should we look at 2nd?
Had the EXACT same issue with a Dremel 200. Thank you!
i guess I am kinda off topic but do anybody know of a good site to watch new series online?
@Will Mohammed I would suggest FlixZone. Just google for it :)
@Micah Dante definitely, I've been using Flixzone for months myself :)
@Micah Dante yup, been watching on flixzone for months myself :)
@Micah Dante yea, I've been watching on Flixzone for years myself :)
You made my day! Thank you! 💯
A minha parou de funcionar e desaparafusei toda, retirei os carvões, e acabo de ver no vídeo que faltou o adesivo...rs... não quis cortar, descolar, achando que não abrira por faltar algo... o vídeo é espetacular. Obrigado!