when I try to import new dxf file, program said that incorrect rotor geometry: left boundary is not vertical line but same dxf file can work different FEM programs, how can I solve it please write me: ilkerozturk58@gmail.com regars
A wonderful tool,thanks for the pain taken to come up with the same. For fractional pitch winding it's asking to set up the winding pattern manually,which I did, however I am unable to generate mesh as it is not allowing antipweiod setting for the same,please help.
Hello I ma not able to import the dxf file for an IPM rotor. The geometry editor gives me an error saying "Incorrect rotor geometry: outer boundary in not a circle with center at (0,0)" Can you please help with this as i am quite sure the rotor is centered at origin. Also does the editor except varying radius rotor (petal shaped) as dxf. Thank you.
Hello sir , can i ask about this simulating ?? When i operate fo generator mode magnetostatik . We set current supply and set advance angle to 180°. So why we know about voltage and i input power (mechanical) and output power ( electrical) . Because the result of in&output is minus . Thankyou for your reply . I hope yo read this question 🙏🙏
Its really perfect job! thank you very much for sharing. i can not rotor or stator dxf import, what is the exact dxf properties that works on program. I have applied what is written in the manual, but still could not be successful. may catia be problem? Is there a dxf editor you can recommend?
Yes, I recommend using LibreCAD, it always works fine with MotorAnalysis. SolidWorks and others may not work with MotorAnalysis, but they work perfectly with MotorXP, our new software (motorxp.com/)
Typically, specify the number of mesh slices the same as the number of magnet segments in the shaft direction - it provides the most accurate results for rotors with skewed magnets as each mesh slice will be at the center of the magnet segment. However, to reduce the simulation time 3 mesh slices is sufficient in most cases. If there is no skewing, the number of mesh slices is always 1.
Hello sir , I have probelm for import dxf rotor ( In matlab command window have text " maltab.graphics.internal.figfile... eror while evaluating menu callback" , why sir ? Thank you
You have developed very good software, thank you very much for sharing, great work! Ps. do you have any good text about brushless motor design and optimization? I would like to be more accurate in my designs
Hi Vladimir Kuptsov! A wonderful product....May I request you to help me figure out a way to install this...after the installation when I try to open the program, I get the following error - "The procedure entry point ucrtbase.terminate could not be located in the dynamic link library api-ms-win-crt-runtime-l1-1-0.dll.". Can you help me please. Thanks!
hi. I downloaded software of PM software but unable to download install it . First it gave "error code 12029" now it gives "error code 12157". My setup is Win7 Professional & Service Pack 1 . Do you know the reason why i couldnt install it ? Thank you
app does not work on windows 11. it keeps saying it is having an issue with the materials folder. wasted half an hour downloading it and trying to use it
Software installed fine, both standalone and MATLAB-supported. I can run the Prius example OK but that's it, the outer rotor example doesn't load. On worked examples from various textbooks (and a real motor) it simply either won't accept the geometry or won't generate winding data. If I put the winding data in manually it sometimes generates a pretty picture but the simulation wont run. Sadly the error messages and the manual don't explain why it's unhappy or what to do next :( I'm sure this is great software but it needs more working examples and better error information. I appreciate it's free, but as an impoverished student I can't afford to pay for tech support. Has anybody else got an independent working example I can look at?
What are the problems with other 2 examples? Can you please contact me at 2v.kuptsov@gmail.com? We can arrange day and time to connect to your computer with TeamViewer and solve your problems.
Vladimir, after standalone .exe file (PM) downloaded I have an error HTTP 12029. Rerun installer and Firewall settings doesn't help. Any cure for that?
@@yurimakarov6214вроде эту проблему решил, но было ещё что-то что остановило меня от дальнейших попыток. Интерес ещё остался, попробую поставить заново.
Hello sir I've installed the IM version for matlab but when I write 'motoranalysis' in the command window nothing happens. I tried to change the file location and I put it in the matlab file but it did not work Is there a spacific location that I need to move the file to? By the way I installed the standalone version but it didn't work either. Thank you
Hello, I will send you an email tomorrow. An engineer from China encountered some problems during the software installation process. I will send you an email tomorrow to explain my problem in detail. Thank you for your technical sharing. I am looking forward to Use your software
@@motorxp I checked there but not found any download option. Can you please check this, it's my emergency situation for me to design an ipm motor, it's my last month of my masters program
I could not understand the rotor import part. Should i draw the all rotor and magnets or just draw a part of it ??
Is it possible to verify the behavior of a magnetic field due different types of voltages and loads applied in rotor shaft, using this software ?
MotorAnalysis-PM will be available in a few days
MotorAnalysis-PM is now available!
when I try to import new dxf file, program said that incorrect rotor geometry: left boundary is not vertical line but same dxf file can work different FEM programs, how can I solve it please write me: ilkerozturk58@gmail.com regars
How to install PM with matlab ? What mean the "change current folder to folder aplication file" in manual modul ??
MotorAnalysis-PM is now available!
Hello can you please send me your email address I have to tell you my problem.
i did the exact thing but the geometry still error
A wonderful tool,thanks for the pain taken to come up with the same. For fractional pitch winding it's asking to set up the winding pattern manually,which I did, however I am unable to generate mesh as it is not allowing antipweiod setting for the same,please help.
For fractional slot winding you should select Boundary conditions as 'None' in Mesh Editor
Vladimir Kuptsov thank you
Pushpa Geopal, hello sir , please help me for instalation procedure 🙏🙏
Hello
I ma not able to import the dxf file for an IPM rotor.
The geometry editor gives me an error saying "Incorrect rotor geometry: outer boundary in not a circle with center at (0,0)"
Can you please help with this as i am quite sure the rotor is centered at origin.
Also does the editor except varying radius rotor (petal shaped) as dxf.
Thank you.
Hello, please send me your dxf to 2v.kuptsov@gmail.com, I will take a look.
Hello sir , can i ask about this simulating ?? When i operate fo generator mode magnetostatik . We set current supply and set advance angle to 180°. So why we know about voltage and i input power (mechanical) and output power ( electrical) . Because the result of in&output is minus .
Thankyou for your reply . I hope yo read this question 🙏🙏
The minus for input power in generating mode just tells that the electrical energy is going out of the motor
Its really perfect job! thank you very much for sharing. i can not rotor or stator dxf import, what is the exact dxf properties that works on program. I have applied what is written in the manual, but still could not be successful.
may catia be problem? Is there a dxf editor you can recommend?
Yes, I recommend using LibreCAD, it always works fine with MotorAnalysis. SolidWorks and others may not work with MotorAnalysis, but they work perfectly with MotorXP, our new software (motorxp.com/)
@@motorxp thank you my problem solved. actually problem is to long name string dxf file, i mean directory adress.
Well done!
How to treat this simulation for generator ??
Hello sir, how to determine number of slice if there are skew ??
It software is only for computer 64 bit ??
The great software, hello sir how to determine number of slice if scew mesh editor ?? Thank you
Typically, specify the number of mesh slices the same as the number of magnet segments in the shaft direction - it provides the most accurate results for rotors with skewed magnets as each mesh slice will be at the center of the magnet segment. However, to reduce the simulation time 3 mesh slices is sufficient in most cases. If there is no skewing, the number of mesh slices is always 1.
@@motorxp oke sir thank you 🙏🙏
Awesomely great job! Thanks for sharing it!!!
Thank you!
Hello sir , I have probelm for import dxf rotor ( In matlab command window have text " maltab.graphics.internal.figfile... eror while evaluating menu callback" , why sir ? Thank you
Please contact me directly at 2v.kuptsov@gmail.com; please also attach your dxf file for analysis
I have been unable to get the software to run on my Windows 10 PC. It launches the window for about 50 milliseconds and then disappears.
Can you please send me a screenshot of the error it shows in the black window before it disappears to my email 2v.kuptsov@gmail.com?
Same problem pls help any updated
You have developed very good software, thank you very much for sharing, great work!
Ps. do you have any good text about brushless motor design and optimization? I would like to be more accurate in my designs
Thank you! You can review my recent publication www.mdpi.com/2075-1702/7/4/75
@@motorxp Thank you very much for your answer, I'm reading it.
instablaster
sandwich Drones. Hello sir, please tell me about How to Install this software . I think this software benefical for me ?
Hi Vladimir Kuptsov! A wonderful product....May I request you to help me figure out a way to install this...after the installation when I try to open the program, I get the following error - "The procedure entry point ucrtbase.terminate could not be located in the dynamic link library api-ms-win-crt-runtime-l1-1-0.dll.". Can you help me please. Thanks!
Hi Abishek Ramesh! Sorry for late reply. Can you please send me screenshots of the error at 2v.kuptsov@gmail.com?
Just the quick glance gave me this appuals.com/how-to-fix-the-procedure-entry-point-ucrtbase-terminate-is-missing-or-could-not-be-located/
hi. I downloaded software of PM software but unable to download install it . First it gave "error code 12029" now it gives "error code 12157". My setup is Win7 Professional & Service Pack 1 . Do you know the reason why i couldnt install it ?
Thank you
Does it work on MacOS if you have MatLab?
Most likely it won't work on MacOS
I am having problem in rotor import for bldc motor plz help!!!
Hello sir, please tell me how to instal motoranalysis PM standalone and with matlab ? thankyou very much
app does not work on windows 11. it keeps saying it is having an issue with the materials folder. wasted half an hour downloading it and trying to use it
This version of MotorAnalysis-PM was not tested with Windows 11
подскажите, а он работает отдельно от матлаба?
no matter how many slots i enter it says incorrect number of slots or winding layers, i want my 750MB of download back
Please provide more information to info@motorxp.com
Ok thanks alot , email sent
How do I get training for this package and what is the cost?
motoranalysis.com/index/training_courses/0-46
Software installed fine, both standalone and MATLAB-supported. I can run the Prius example OK but that's it, the outer rotor example doesn't load. On worked examples from various textbooks (and a real motor) it simply either won't accept the geometry or won't generate winding data. If I put the winding data in manually it sometimes generates a pretty picture but the simulation wont run. Sadly the error messages and the manual don't explain why it's unhappy or what to do next :(
I'm sure this is great software but it needs more working examples and better error information. I appreciate it's free, but as an impoverished student I can't afford to pay for tech support.
Has anybody else got an independent working example I can look at?
What are the problems with other 2 examples? Can you please contact me at 2v.kuptsov@gmail.com? We can arrange day and time to connect to your computer with TeamViewer and solve your problems.
@@motorxp Hello sir can u say me how to install the software.
@@seemaangadi8054 The installation is the same as for any other Windows program
@@motorxp this software can't instal in 32 bit ??
@@farhanhakimul8053 Only 64 bit is currently supported
we are not able to log in , kindly help .
Please give me your email, I will send you new password.
Vladimir, after standalone .exe file (PM) downloaded I have an error HTTP 12029. Rerun installer and Firewall settings doesn't help. Any cure for that?
Can you please send me the screenshot with the error to 2v.kuptsov@gmail.com?
same here @@motorxp
did you find the solution ? please help
@@yurimakarov6214вроде эту проблему решил, но было ещё что-то что остановило меня от дальнейших попыток. Интерес ещё остался, попробую поставить заново.
I have installed the software motoranalysis-PM but it is not opening will you help me?
you gotta open it from inside the folder where it is located not the shortcut
Hello sir how to threat software for generator ??
The Website is not available, where is the tool also available?
The website is available now, sorry for inconvenience
How can I download this software
Hello sir
I've installed the IM version for matlab but when I write 'motoranalysis' in the command window nothing happens.
I tried to change the file location and I put it in the matlab file but it did not work
Is there a spacific location that I need to move the file to?
By the way I installed the standalone version but it didn't work either.
Thank you
Hello, does it provide any error message? Please contact me at 2v.kuptsov@gmail.com
Hello, I will send you an email tomorrow. An engineer from China encountered some problems during the software installation process. I will send you an email tomorrow to explain my problem in detail. Thank you for your technical sharing. I am looking forward to Use your software
How about your instalation problem ?
Can this software be used to model permanent magnet generators?
Yes it can, you need to specify advance angle more than 90.
Vladimir Kuptsov, what about axial flux permanent magnet generators?
@@danbramhall5966, axial flux machines are not yet supported
@@motorxp what this mean
@@motorxphow much angle to be generator ??
hello,
could you tell me, how to install motor analysis-PM
What kind of problem do you have? Please contact me to 2v.kuptsov@gmail.com
Hello sir,
i can't to download this software please send me the link to download
Hi, you should sign up or log in to download the software. What kind of problem you have?
Can anyone tell me how to download this software
From motoranalysis.com
@@motorxp I checked there but not found any download option. Can you please check this, it's my emergency situation for me to design an ipm motor, it's my last month of my masters program
It software can Simulation the generator ??
Sure
@@motorxp How to install this software with matlab ??
What the fuction of file motoranalysisPMv1.1_matlab.zip ?
@@motorxp please help me 🙏🙏
@@motorxp hello sir, please tell me about how to simulate this software for generator . Thankyou sir🙏🙏
@@farhanhakimul8053 To simulate generator mode you need to set up advance angle to 180
как запустить версию standalone?
It's not opening
I can't download this software sir please send me the Google drive link to download
please let me know you email
Please send me the link for download this software
I m getting error
Plz help
Please send the error description and screenshot to 2v.kuptsov@gmail.com
this is not working
what exactly is not working?