Заебись реставрация! Разобрать, помыть, собрать и не работающий ранее компрессор вдруг обретает второе дыхание. Можно было не разбирать, просто покрасить и всё, результат был бы такой же ошеломительный.
I really enjoyed this video. You make reservation look so easy. This was the first refrigerator compressor I have seen restoration. Thank you for sharing I look forward to your next restoration.
Many years ago (80s) helping my father in his commercial refrigeration business, we did this type of repairs on air conditioner compressors, usually it was a damaged valve or a burned coil and had to be rewound again. The problem with these repairs is that they are bound to not last long due to all the debris that gets into the system during welding. After quite a few repairs we started recommending the customer to buy a new compressor when the failure within the compressor itself. This video made me go back in time. Thank you very much for this video.
Me too. I worked rebuilding semi-hermetic compressors. So, no welding involved but we did inspect and measure every part, reground or replaced the valves machined as needed. He didn't even remove the piston to check out the cylinder, wrist pin ect. If it can't blow up a balloon, how is it ever going to build up enough head pressure?
17:39 непонятно зачем было протыкать шарик? Не смогли дождаться пока шарик сам не лопнет? После реставрации компрессор не выдаёт нормальное давление и нет производительности?
The balloon should have blown up a lot quicker and exploded sooner. You must have a leak around the weld area. You should have ground on the edge, not cut into the side above the edge. Then the weld would be on the edge and have a stronger weld. There was no need to cut into the inside as it was clean, until you got metal cutting dust inside.
Infelizmente, não temos tantos profissionais como você que deixam as coisas velhas como novas novamente.... Parabéns pelo seu trabalho!!!! Unfortunately, we don't have as many professionals as you who make old things like new again.... Congratulations on your work!!!!
Bien fait, mais je vois bien qu'il ne soit pas bien bien fait ! Car je sais qu'il y'a des pertes dans le châssis au niveau de la chambre de compression 🧐🤏👁️😉
Funny how he took the piston rod cap off twice. That unit was clean inside. Pobably would have worked just fine. The oil was even clean. Where`s the severe damage???
Ballon test was great. The granddaughter thought it was funny when it popped!!😀😀😀😀😀
One of the famous Thailand product amazing
Заебись реставрация! Разобрать, помыть, собрать и не работающий ранее компрессор вдруг обретает второе дыхание. Можно было не разбирать, просто покрасить и всё, результат был бы такой же ошеломительный.
А там все время такая реставрация помыли живой водой и все заработало!
он чё то мой стари начальника вспоминает он всегда обмонивал 😁😁
I really enjoyed this video. You make reservation look so easy. This was the first refrigerator compressor I have seen restoration. Thank you for sharing I look forward to your next restoration.
wow boom👏👏👏
excellent 👍 my friend ❤️
You clean it and re assamble it, but didn't fix it. it has no compression at all
Many years ago (80s) helping my father in his commercial refrigeration business, we did this type of repairs on air conditioner compressors, usually it was a damaged valve or a burned coil and had to be rewound again. The problem with these repairs is that they are bound to not last long due to all the debris that gets into the system during welding. After quite a few repairs we started recommending the customer to buy a new compressor when the failure within the compressor itself. This video made me go back in time. Thank you very much for this video.
Me too. I worked rebuilding semi-hermetic compressors. So, no welding involved but we did inspect and measure every part, reground or replaced the valves machined as needed. He didn't even remove the piston to check out the cylinder, wrist pin ect. If it can't blow up a balloon, how is it ever going to build up enough head pressure?
mở đến đó thì mở luôn cả piston xem còn ổn ko luôn đi chứ bác
17:39 непонятно зачем было протыкать шарик? Не смогли дождаться пока шарик сам не лопнет? После реставрации компрессор не выдаёт нормальное давление и нет производительности?
Good job! Great engine to make a homemade airbrush compressor.
Impresionante mantenimiento......
Я тебе каждый день смотрю
Excelente trabajo, saludos desde Buenos Aires.
No entendí una mierda
Alllahji
I think you forgot to add oil
Excelent
Вау новые видео на канале
Good job.
Greetings from Brazil.
'好手工
بطل
الضغط بتاعه ضعيف جدا . لا يصلح للثلاجة مرة اخرى
🙏☝️🙏☝️🙏☝️🙏☝️🙏☝️
А откуда появилась наклейка к данными о компрессоре?
Good ii boss 👍👍😊😍
fatto bene anche se nel finale avrei usato un discchetto da finitura lamellare
i wonder ,How you made compressor suck all the oil in..? Thanks
Круто
8:30
Reference to the Microwave repair by Restoration Skills
Anda memotong di titik yang salah
Thằng này việt nam hả anh em?
The balloon should have blown up a lot quicker and exploded sooner. You must have a leak around the weld area.
You should have ground on the edge, not cut into the side above the edge. Then the weld would be on the edge and have a stronger weld. There was no need to cut into the inside as it was clean, until you got metal cutting dust inside.
If weld was leak nothing to do with discharge line..coz discharge line coming from pump and dome is suction area..that hold gas..refrigerant
More likely bad valve or blow by. I didn't see him remove and inspect the piston and cylinder bore.
If is repaired the compressor must have 350 or 400 PSI of pressure for use it, I think that the pressure is not enough
Wasted 18.17 minutes of my life - sorry………
11:30
Same reference just with a different material
Bom trabalho 👏👏
Infelizmente, não temos tantos profissionais como você que deixam as coisas velhas como novas novamente.... Parabéns pelo seu trabalho!!!! Unfortunately, we don't have as many professionals as you who make old things like new again.... Congratulations on your work!!!!
Fake kkkkkkkkkkkkkkkkkkkkkkkkkkkk
👍
No se hace asi desde la abierta.
Bien fait, mais je vois bien qu'il ne soit pas bien bien fait ! Car je sais qu'il y'a des pertes dans le châssis au niveau de la chambre de compression 🧐🤏👁️😉
CFC gas.
very weak pressure
Solo hiso el video no le probó cuántas libras de presion subió
Funny how he took the piston rod cap off twice. That unit was clean inside. Pobably would have worked just fine. The oil was even clean. Where`s the severe damage???
Actually, you did nothing to that compressor except removing rust and painting 😂
You didn't even change the seals 😢
get a new one!
Ese compresor está mal reparado se demoró demasiado en llenar ese globo de aire la mofla está mala
pert de temps pour rien
fake
What a waste of time. Do you even own a pressure gauge or a micrometer?