Hi there, thanks for showing the item, helps a lot to imagine how small the item is when I have never seen or owned such a mini saw. At the 10 minute mark, you were showing the wood kicking back, that's actually because you're touching the wood you are pushing through the blade to the wall to the left. If there was no wall, the wood would just be sitting there and not kicking back towards you. Rule for table saws, and I think this is the same too, to not use both the wall plus the mitre to cut anything, as the saw continuously spins and the wood will get pushed to only one direction when being in contact with the saw. The wall gives another point for the wood to be leaning against and pushes to you. If anyone were to need to cut a longer piece than the 7 cm length, it would be far safer to take out the wall on the left, and just use the mitre while wearing safety glasses.
Well thank you for this information, it is true that I am not used to using these mini machines, but it is certain that this guide on the left is used to cut a board lengthwise and not really to cut as I do on the video. Besides, I even put the guide upside down at the start of the video lol, which I then corrected. In the end I prefer to use my big table saw that I have in my workshop, at least I can adjust the blade height which is not possible on this mini table which I find quite dangerous. In another video I modified the tray and also made a cover for the saw blade which is much safer, but in the end I almost never use it, so it's a purchase that is not very useful to me.
And yes here I am again 😄 The holidays are over, we have to put it to work. Too bad, doing nothing was great 😄 Thanks for watching and good comment Brian 😊👍
Excellent review! I’m not a pro-woodworker by any stretch, but I can see where this unit might be improved upon. • Not have the blade so high or somehow make it adjustable • Have an extension arm coming from the miter gauge to better hold the piece you’re cutting • A remote off/on push button switch that you can place on the floor • I’m assuming this unit can be bolted down/secured?
Hello, you are right about all these improvements. I worked on this machine to make it safer by making a cutting plate which attaches to the original one which allows the blade to stick out less, then I enlarged the cutting guide and I I also made a cover for the saw blade which lifts as the piece of wood to be cut passes. Now I'm more reassured after making these changes.
So did you ever make the modifications on this saw? If so, will you make a video showing them off? I have this saw as well and i love it, however i do not use the sanding wheel, of the fence and plastic guard thing on mine. I do crosscuts and a fence is not recommended for crosscuts on a tablesaw.
ruclips.net/video/r8njyeozcPk/видео.html Yes I made a video here: ruclips.net/video/r8njyeozcPk/видео.html with some modifications, the main one for me was to make a protective cover for the blade. By enlarging the cutting deck I can no longer use the sanding wheel but it's something I didn't use so no problem for me 😊
Looks fairly dangerous to me! And cutting with the sliding miter gauge, and the other end of the wood against the rip fence is just asking for super dangerous kickback! But removing the fence also removes the blade “protection” (its a stretch to call it protection!)! This was a great, honest review! An Amazon find I guess?
I agree with you, it's a dangerous machine, I bought it on banggood and I wondered how we could sell this kind of machine without any protection and besides I talk about it in this video. But by purchasing this machine knowingly (from a safety point of view) I already had my idea to remedy all these problems. I also made another video on all the improvements I made to this machine which is now very good for small woodwork. Thank you for your kind comment 😊
Great video. I look forward to your video on the solutions. This baby was just delivered this afternoon. I haven't put it together yet. Your review was most timely!
It is a good little machine and practical. I improve this circular saw and most importantly I secure them. If you are interested here is the link the video : ruclips.net/video/r8njyeozcPk/видео.html Thanks for your great comment 😊👍
Oui enfin je me remet au travail 😁 C'est une machine sympa mais dangereuse a mon gout, je vais devoir l'améliorer pour qu'elle soit plus sécurisante, je tien a mes doigts 😉👍
Hello, the sanding discs that you see in the video were delivered with the machine, now I buy some in a DIY store but I have to cut them with scissors because all the ones I find are too big for the machine.
This is a problem because I can't find a replacement blade. All the ones I found that could have fit were too large in diameter. Maybe I should look at the mini circular saws that runs on battery, the size could correspond.
Thank you my friend, I must improve this machine, it is very practical but too dangerous, I hold too much to my fingers 😁 Thanks again for your great comment 😊👍
looks great for cutting small hobby objects but! as with all tools danger is just around the corner if one does not plan ahead. as a tradesman I will be buying one soon for my modelling hobby.
@@satorrotas no problem Mate! i have the tradesmens de walt full size, very dangerous!! I have seen guys removing the guard as well a very stupid thing to do!
This looks very dangerous, nobody should be using a table saw without a riving knife and without being able to adjust the blade height. Very dangerous.Also, if you use the mitre gauge to push the wood through the blade then you do not need to use the fence, one or the other, not both. That is why your piece of wood was getting stuck between the blade and the fence. Very dangerous. Next time, remove the fence. Good luck to you!
I agree with you this machine is dangerous. But I made some modifications to this machine in another video which make it safer. I made a thicker cutting deck so that the saw blade protrudes less and also a blade cover. Now it's much better 😊👍
Hi Sator, Did you come up with a solution to the saw blade cover? I have a mini trim saw I mainly use to cut small pieces of gemstones to size before I facet them. I would like a cover over the blade to prevent water from splashing onto my face when I am cutting the stone.
Hi. Yes I made a cover for the blade with plexiglass 3 millimeters thick, I give you the link of the video: ruclips.net/video/r8njyeozcPk/видео.html it's from 8:31 of the video 😊
I am a hobbyist and I came across a Vevor mini table saw but for some odd, and poor advertising, they don't show complete pictures of their kit. So that's what brought me here and now I have a full idea of what their kit can do. So thank you for posting your video. The video was very clear. That said, and this is just my 2 cents and no offense intended, why don't you just narrate instead of hand gestures and without background music? I think you'd be able to explain certain things better. But, its just my opinion. Thanks again!
Thanks for your good comment. I don't speak English at all, so to make my videos I thought that doing the subtitles myself was a good solution, but I realized that in the end it was better that I speak in my language and that the people who watches my videos uses the translation that youtube makes available. That's what I do now 😊 Thanks again 😉👍
@@satorrotas My apologies! Like I said, I wasn't bashing your video just throwing out my opinion or thought. But again, nice video. It helped me to understand the product better. Keep up the great work!
Thanks and no problem for your comment which was really nice, I like when people give their opinion especially when it's said nicely. Very happy if my video was able to help you. Have a good day Dan 😊👍
Yes there is but the price is much more expensive, then I think that safety is more important. I have made modifications to make this machine safer such as a cover for the saw blade, a larger cutting deck, but I think it is better to look on Amazon and buy a machine with all the necessary safety features.
Pascalll!!!! Welcome back to you tube buddy. Missed ur content brother 👍 hope u sorted ur other projects out. I no ur been bizy doing other stuff. Awesome video on the lathe an issues there are. Brilliant. 👍 😊 👍 bro.
Thank you, and yes I'm back, it's a shame the holidays are over 😁 Lots of projects in progress, I needed a little more machines for my constructions. Just put some security on this machine and it will be great 😉👍
Looks like the plexy kickback shield prevents you from properly supporting the material on the binding side of the blade. And increasing the risk of kickblade. The desighn could really use a better safety mecanism.
It's true, this saw is good but I find it dangerous because there is no safety. In another video I changed some thing and now this saw is much better 😊👍
It was so good to watch and hear your intro again. If you were to mount your cutting deck upon extended uprights, could you perhapd end up with a more conventional saw height without making the machine too top-heavy?
Hello Del, how are you ? good I hope. You had the same idea as me 😉 I have almost finished improving and especially making this machine more secure, I would make a video to show how I did. Hope this helps people who have the same circular saw 😊👍
@@satorrotas I'm very well, thank you, Pascal. It's very good to know that you're okay too. I think it is irresponsible to retail this machine with such a low cutting deck. It really is unsafe, especially for inexperienced users.
@@Del350K4 That's right, I do not recommend buying this machine, the best is to take a more expensive one with the possibility of adjusting the blade in height and a cover for the blade, it is a minimum of safety. Although these machines, whatever they are, are always dangerous 😊👍
Yes a video, been a long time since the last. Wow that's a finger chopper, so many ways to cut oneself. I'm with you covers on the 3 sides, the guide is very loose could be better. Then no blade adjustments that could have been done like a Skil saw. The sander disc a direct mount better as it seems so far from the table and no surface in front for a flat sand.
Yes a lot of things to improve on this circular saw, I find it really dangerous, I regret having bought this model but now that it is here I have to find solutions, because my fingers are much more important than this machine. I will make another video to show what I have improved hoping it helps people who have this circular saw. Thanks for your great comment, have a good day my friend 😊👍
Hello Pascal glad to see you have returned i think this is a pretty handy machine but should definitely have a guard that covers the blade completely like a full size table saw does especially if it runs when running the chuck i have looked at these also I would like to have a small chop saw for brass and aluminum stock
This table saw comes with other blade for plastic, brass and aluminum which will be good for my constructions. But before, you really have to do more safety, I have already started and I would do another video on this circular saw once the job is finished. There is also the part where there is the engine which is not protected, and the tools come to magnetize on it which is also very dangerous. But once securing this machine will be really very practical 😊 Thanks for watching and good comment my friend 😊👍
Awesome little machine, i call these saws “widow makers” hahaha, i have had so many close calls with my fingers and bits of wood come flying back, everytime i counted my fingers after using it 😅 great video my friend 👍🏻
It's a nickname that fits this machine very well 😁 I have to improve it because I find it really dangerous. All these kinds of machines are dangerous but I find that this one there more particularly. I started the work to improve it, I would use it once I'm done. Have a nice day Harley 😉👍
Let me preface with, all saws are dangerous. That said, are these mini saws really that bad? I was thinking of getting one. Is it a bad idea to buy one ?
Very nice mini tool for the hobby, you need to hold it with clamps to the table and use a wood block as a support for the sanding disck 🔵🔵🔵👍👍👍✔️✔️😀😀🔵🔵🔵
Thank you for your advice carlos, but before using this machine I must secure it, as it is I find it too dangerous. Thanks for your great comment my friend 😊👍
Bonjour, pouvez-vous me dire la marque de votre scie miniature et où vous l'avez achetée, s'il vous plait. le montage est-il compliqué ? Merci de votre réponse et bon weekend.
@@dominiquebodeau298 Bonjour, il n'y a pas de marque pour cette scie. Je l'ai acheté sur le site banggood et il n'y a pas de montage spécifique. Mais attention car elle n'a aucune protection de lame et c'est très dangereux. Vous pouvez en trouver sur Amazone ou autre site dans les mêmes tarifs a peut prêt avec une protection ce qui a mon avis est plus prudent. Bon weekend à vous aussi 🙂
@@satorrotas ah d'accord, merci de votre conseil je vais aller voir sur amazon , en même temps j'ai déjà une scie électromagnétique, peut-être que ça ferait double emploi ?
Si vous avez une scie électromagnétique je suis pas sur que la scie circulaire vous soit très utile, a moins que vous vouliez couper des section plus importante, mais dans ce cas il vous faudrait une scie circulaire avec la lame qui ce règle en hauteur et je pense que ce serait bien plus cher 😊
@@satorrotas bonjour. Merci pour votre réponse. Et vos conseils. Du coup je ne vais pas investir dans une autre scie. Passez une bonne journée. Dominik
That is a very cool multy function machine I like it but they fact that there is no protection on the cutting disc and the depth is not adjustable that would but me off . Glad to see you back 😊
Yes, this machine will make my work easier, but first I have to improve it and especially find a solution for the height of the blade. This circular saw is not secure and it is dangerous. I started work on it, I will make a video, hoping to help the people who have this machine. Thanks for your good comment my friend 😊👍
Like you say definitely needs some improvements. But after that should make a fine Little table saw. Do you have a link for it? Great work again my friend👍🏼😁
I bought this circular saw from Banggood but I have seen others cheaper and better secure on Aliexpress, I do not recommend this machine because it is not secure at all. I would do another video on this machine once I complete the safety job. But it is sure that this circular saw will facilitate my work for my constructions 😊 Thanks for your good comment my friend 😊👍
salut😁👋, sa fait un bail😅. dsl🙏. mais sa fait plaisir de retrouver tes video👍👍. par contre tu es sur que c'est en vent libre ce truc😱. enfin surtout la scie. le coté ponceuse dremel me plais bien🤩. merci du partage et á bientot, bonne soirée Pascal😃✌✌
Il est certain que l'on ne pourrait pas acheter ça en France, c'est vraiment pas sécuriser, donc avant de m'en servir je vais trouver des solutions pour l'améliorer. Merci pour ton commentaire, passe une bonne journée Marco 😊👍
Hola Pascal Amigo 👋. Me alegra mucho saber de ti 💪. Buena maquina, se puede hacer de todo 👌y para tus trabajos se vé genial 👍. Que pases un buen día 💃Un saludo cordial desde España 😎🚗💨💨💨🤝💨💨🇪🇸
Now I understand better why you upgraded this machine, it was really too dangerous. It is very practical and it does not take up space but in terms of security it was really not at the top. Very buy and great video 👍
Hey Pascal I wanted to let you know Stevo D passed away and I will try and get that camper out one day this week been super busy stay safe my friend 🤟🏼
I am so sorry to hear this sad news, all my best thoughts will go to his family 🙁 No problem, work comes first, very happy to hear from you, take care of you and your family Travis.
Thanks. I just watched two videos on tablesaw kickback, it's very informative. They are very dangerous machines, I don't use them often but I try to be very careful when I work with them.
Not going to read all the comments to see if the following was covered: I own one of these saws, do not know why because it is clear #1 the blade height can not be adjusted. #2 The miter slide wobbles in the slot in the table. Far too much clearance. (On my unit my factory supplied miter is different then what is shown in the video) #3 WORSE THING: The table top is attached to the base using ONLY four threaded TUBES . Nothing else supports/OR ALIGNS the top plate to the blade. All it takes is for one of the attching screws to loosen and the top plate WOBBLES and distroys alignment between blade and miter. I use this saw for model making, it was a waste of money. (Have not used the attachments supplied woth the saw)
Certain subject has been discussed, but it is certain that if we want security this is not a machine that I would recommend to people, it is better to pay a little more and have good equipment 😊👍
Sí, todo está bien aquí, mis vacaciones terminaron, lástima que fue bueno no hacer nada 😄 Gracias por tu gran comentario, que tengas una buena semana para ti y tu familia Victor 😉👍
I will improve this little machine, because as you say it is too dangerous as it is. It is certain that this will help me a lot for my dioramas, but it will only be useful when I have all secured. Thanks for your good comment, have a great day Jan 😉👍
Well Pascal. First of all it is great to see you back in action.. :) I have to agree with your review on this machine. Has a lot of awesome features but (in my opinion) no real thought went into actually making it. You of course have found all the issues with this machine. Unfortunately it is not a matter of "if" you will get hurt on this. It's a matter of "when". With the belts all exposed under there as well. YIKES. Thanks for sharing bud and again great to see the name pop up in the videos.. :)
You are right, I must be very careful with this machine, my fingers are the most important. I have to improve it because I find it really dangerous. All these kinds of machines are dangerous but I find that this one there more particularly. I started the work to improve it, I would use it once I'm done. Thanks for your great comment, have a good day Nick 😊👍
That's right, I did not pay attention when buying this machine that the blade was not adjustable in height which is really a shame and dangerous I find.
It's an good idea, but I'm not sure that the screw that holds the saw blade is of good quality, so I prefer to leave it in place and make a cover for the blade 😊👍
I've never seen such a small table saw. It has so many other options included. I can see, you need to work with safety in mind. It looks fairly heavy duty. Yes, they should have covered the sides as much for safety as keeping the area clean. You have a good plan going forward👍Like 54
It's a good mini circular saw but not enough safety, I made another video on this saw to show how I secure them, now it's much better. Thank you very much for your excellent comment 😊👍
It's probably a good idea to leave all the extra attachments, sander, etc., off while using the saw. It's dangerous enough without having another thing to bump into while cutting.
It is certain and I agree with you, but I only use this saw for my dioramas. It is obvious that for heavy work one would need one on feet and which are intended for the work of large pieces of wood.
Simply because it has no name, apart from "mini table shaw". I give you the link, you can check for yourself : usa.banggood.com/Multifunctional-Small-Cutting-Mini-Table-Saw-DIY-Woodworking-Angle-Table-For-Metal-Cutting-Carving-p-1891048.html?imageAb=2&cur_warehouse=CN&ID=47184&rmmds=search&a=1658586007.8056&DCC=US¤cy=USD&akmClientCountry=FR
Really useless comment and really not nice, first hello, then if you had watched the video in full you would have seen that this machine comes from banggood and that there is no brand. Furthermore, when someone asks me for more information on this or that thing, I answer them with courtesy. Have a good day anyway
Странный какой-то пользователь! Зачем обязательно надо одновременно и Патрон и пильный диск использовать? Сними параллельный упор и режь рейки любой длины. Сними транспортир и оставь параллельный упор и режь фанеру!
Станок продается так, я сделал еще одно видео, где преобразовал этот станок, убрал патрон, который бесполезен, сделал режущую пластину большего размера, оставив направляющую. Это машина для небольших работ, и она не имеет безопасности. Но для того, что я хочу сделать, этого вполне достаточно. Спасибо за ваш комментарий 😊👍
Good review. Thank you. Excellent safety comments too!
Thank you very much 😊👍
Hi there, thanks for showing the item, helps a lot to imagine how small the item is when I have never seen or owned such a mini saw. At the 10 minute mark, you were showing the wood kicking back, that's actually because you're touching the wood you are pushing through the blade to the wall to the left. If there was no wall, the wood would just be sitting there and not kicking back towards you. Rule for table saws, and I think this is the same too, to not use both the wall plus the mitre to cut anything, as the saw continuously spins and the wood will get pushed to only one direction when being in contact with the saw. The wall gives another point for the wood to be leaning against and pushes to you. If anyone were to need to cut a longer piece than the 7 cm length, it would be far safer to take out the wall on the left, and just use the mitre while wearing safety glasses.
Well thank you for this information, it is true that I am not used to using these mini machines, but it is certain that this guide on the left is used to cut a board lengthwise and not really to cut as I do on the video. Besides, I even put the guide upside down at the start of the video lol, which I then corrected. In the end I prefer to use my big table saw that I have in my workshop, at least I can adjust the blade height which is not possible on this mini table which I find quite dangerous. In another video I modified the tray and also made a cover for the saw blade which is much safer, but in the end I almost never use it, so it's a purchase that is not very useful to me.
Great video welcome back buddy good to see you again sator rotas have a nice day friend 😊👍🏻
Thank you very much my friend 😉👍
@@satorrotas Your very welcome friend I’m glad your back sator rotas and thanks 😇👍🏻
@@ClassicJaggy Thanks 😊👍
@@satorrotas Your welcome friend 😊👍🏻
That is so cool. Should do the trick. Thanks for sharing.
Thanks for your great comment Charlie 😊👍
You are back in the arena, great news and fun tool time with sator rotas, nice one👍
Holidays are over 😁 You have to work a little 😄 Thanks for your great comment and a have good day Wacky 😉👍
Nice video welcome back sator rotas good to see you again buddy have a nice day friend 😎👍🏻
Thanks for your great comment, have a good day for you too William 😊👍
@@satorrotas Your very welcome buddy I’m glad your back sator rotas and thanks 😇👍🏻
@@WilliamB161 Thanks William 😊👍
@@satorrotas Your welcome friend 😊👍🏻
Hooray.!! Pascal is back.!! Very good review, solid return to RUclips.! Glad to see you back my friend.!!
And yes here I am again 😄 The holidays are over, we have to put it to work. Too bad, doing nothing was great 😄 Thanks for watching and good comment Brian 😊👍
@@satorrotas 😊
Excellent review! I’m not a pro-woodworker by any stretch, but I can see where this unit might be improved upon.
• Not have the blade so high or somehow make it adjustable
• Have an extension arm coming from the miter gauge to better hold the piece you’re cutting
• A remote off/on push button switch that you can place on the floor
• I’m assuming this unit can be bolted down/secured?
Hello, you are right about all these improvements. I worked on this machine to make it safer by making a cutting plate which attaches to the original one which allows the blade to stick out less, then I enlarged the cutting guide and I I also made a cover for the saw blade which lifts as the piece of wood to be cut passes. Now I'm more reassured after making these changes.
So did you ever make the modifications on this saw? If so, will you make a video showing them off?
I have this saw as well and i love it, however i do not use the sanding wheel, of the fence and plastic guard thing on mine.
I do crosscuts and a fence is not recommended for crosscuts on a tablesaw.
ruclips.net/video/r8njyeozcPk/видео.html
Yes I made a video here: ruclips.net/video/r8njyeozcPk/видео.html with some modifications, the main one for me was to make a protective cover for the blade. By enlarging the cutting deck I can no longer use the sanding wheel but it's something I didn't use so no problem for me 😊
Looks fairly dangerous to me! And cutting with the sliding miter gauge, and the other end of the wood against the rip fence is just asking for super dangerous kickback! But removing the fence also removes the blade “protection” (its a stretch to call it protection!)! This was a great, honest review! An Amazon find I guess?
I agree with you, it's a dangerous machine, I bought it on banggood and I wondered how we could sell this kind of machine without any protection and besides I talk about it in this video. But by purchasing this machine knowingly (from a safety point of view) I already had my idea to remedy all these problems. I also made another video on all the improvements I made to this machine which is now very good for small woodwork.
Thank you for your kind comment 😊
what a great tools to have
Thank you very much 😊👍
Great video. I look forward to your video on the solutions.
This baby was just delivered this afternoon. I haven't put it together yet. Your review was most timely!
It is a good little machine and practical. I improve this circular saw and most importantly I secure them. If you are interested here is the link the video : ruclips.net/video/r8njyeozcPk/видео.html
Thanks for your great comment 😊👍
Congrats to the new saw... great to see you again
Thank you very much Martin 😊👍
Enfin de retour 👍 sympa cette petite machine ...
Oui enfin je me remet au travail 😁 C'est une machine sympa mais dangereuse a mon gout, je vais devoir l'améliorer pour qu'elle soit plus sécurisante, je tien a mes doigts 😉👍
I'm in the UK, where do you get the sanding belts and cutting disks from as the both seem odd sizes and I can't seem to find any of them?
Hello, the sanding discs that you see in the video were delivered with the machine, now I buy some in a DIY store but I have to cut them with scissors because all the ones I find are too big for the machine.
@@satorrotas Thanks how about the wood cutting blades?
This is a problem because I can't find a replacement blade. All the ones I found that could have fit were too large in diameter. Maybe I should look at the mini circular saws that runs on battery, the size could correspond.
Good to see you back. A great review of this very versatile tool. It does a lot of processes! Thank you.
Thank you my friend, I must improve this machine, it is very practical but too dangerous, I hold too much to my fingers 😁 Thanks again for your great comment 😊👍
@@satorrotas Yes, it does need some safety features. You do so many of your videos showing your hands that losing fingers would not be good at all! 😮
@@RC3DPrintAdventure It is certain, losing one or more fingers would be a disaster, but I will do everything to make sure that does not happen 😊👍
looks great for cutting small hobby objects but! as with all tools danger is just around the corner if one does not plan ahead. as a tradesman I will be buying one soon for my modelling hobby.
I agree with you, with this type of machine you have to be careful. Thanks for your great comment 😊👍
@@satorrotas no problem Mate! i have the tradesmens de walt full size, very dangerous!! I have seen guys removing the guard as well a very stupid thing to do!
This looks very dangerous, nobody should be using a table saw without a riving knife and without being able to adjust the blade height. Very dangerous.Also, if you use the mitre gauge to push the wood through the blade then you do not need to use the fence, one or the other, not both. That is why your piece of wood was getting stuck between the blade and the fence. Very dangerous. Next time, remove the fence. Good luck to you!
I agree with you this machine is dangerous. But I made some modifications to this machine in another video which make it safer. I made a thicker cutting deck so that the saw blade protrudes less and also a blade cover. Now it's much better 😊👍
Good morning Pascal! Great review! Be careful with that thing! 👍😲👍
I will improve this little machine, I find that as it is is too dangerous, thank you very much for your great comment Jeff 😉👍
Handy tool. I like the sanding feature.
A small machine that will be really very useful. Thanks my friend 😊👍
Bonjour Pascale ! Super test, Soyez prudent avec cette Multi-functional table saw!😜👍
Merci beaucoup pour ton commentaire Xavier 😊👍
@@satorrotas 👊😜👍💖
Hello, do you have a link where you bought it
I don't get the link but I bought this machine on the Banggood.com website.
Hi Sator, Did you come up with a solution to the saw blade cover? I have a mini trim saw I mainly use to cut small pieces of gemstones to size before I facet them. I would like a cover over the blade to prevent water from splashing onto my face when I am cutting the stone.
Hi. Yes I made a cover for the blade with plexiglass 3 millimeters thick, I give you the link of the video: ruclips.net/video/r8njyeozcPk/видео.html
it's from 8:31 of the video 😊
nice to see again friend.
Thank you so much my friend 😊👍
Awesome video my friend nice saw good unboxing good stuff great job thumbs up 👍
Thanks for watching and great comment my friend 😊👍
I am a hobbyist and I came across a Vevor mini table saw but for some odd, and poor advertising, they don't show complete pictures of their kit. So that's what brought me here and now I have a full idea of what their kit can do. So thank you for posting your video. The video was very clear.
That said, and this is just my 2 cents and no offense intended, why don't you just narrate instead of hand gestures and without background music? I think you'd be able to explain certain things better. But, its just my opinion. Thanks again!
Thanks for your good comment. I don't speak English at all, so to make my videos I thought that doing the subtitles myself was a good solution, but I realized that in the end it was better that I speak in my language and that the people who watches my videos uses the translation that youtube makes available. That's what I do now 😊 Thanks again 😉👍
@@satorrotas My apologies! Like I said, I wasn't bashing your video just throwing out my opinion or thought. But again, nice video. It helped me to understand the product better. Keep up the great work!
Thanks and no problem for your comment which was really nice, I like when people give their opinion especially when it's said nicely. Very happy if my video was able to help you. Have a good day Dan 😊👍
Hi Pascal. Good to see you again my friend. This is a very interesting video, and I agree the machine needs more safety features 🙂👍
She's really good but it's true that she needs to be secure, I hold my fingers a lot 😁 Thanks for your good comment Holly 😊👍
❤muito legar essa mini serra. Vc saberia me dizer qual a polegadas do mandril w si suporte de lixa? Grata
Não falo português mas presumo que você esteja me perguntando o diâmetro da lixa do mandril, é um diâmetro de 6. Espero que minha resposta o ajude.
@@satorrotas é isso mesmo, muito obrigada 🤗
Is this a home avaiabe in the UK and what’s the approx price. Best regards
I bought this from Banggood so it should be available for UK. The price is around £98
Did you ever find any small machine to make wood cuts that is safer & more practical than this?
Yes there is but the price is much more expensive, then I think that safety is more important. I have made modifications to make this machine safer such as a cover for the saw blade, a larger cutting deck, but I think it is better to look on Amazon and buy a machine with all the necessary safety features.
Hi.
Is it the saw can adjust up and down?
Hi. No, on this saw the blade is fixed, no possibility of adjusting it in height 😊👍
Ok. Tq for your respond
You're welcom 😉👍
Pascalll!!!! Welcome back to you tube buddy. Missed ur content brother 👍 hope u sorted ur other projects out. I no ur been bizy doing other stuff. Awesome video on the lathe an issues there are. Brilliant. 👍 😊 👍 bro.
Thank you, and yes I'm back, it's a shame the holidays are over 😁 Lots of projects in progress, I needed a little more machines for my constructions. Just put some security on this machine and it will be great 😉👍
@@satorrotas awesome buddy 🤠 👍 🇬🇧
@@gazfpv 😊👍
Nice review my friend, welcome back
Thank you so much my friend 😊👍
where ya get it from and whats it called?!?!?!?!?!
I buy them from the Banggood website. It does not have a specific name, just marked table circular saw.
really nice and looks like a great tool for Hobby and more, excellent review and test.....thumbs up my friend and many greetings 👍👍
Thanks for your very good comment, have a great day my friend 😊👍
I was thinking of buying for fun, but thanks for the review, I will look for something safer instead.
You are right, the security on this machine is not good. Thank you for your comment 😊👍
Ah, you’re back. Missed you.
Thank you, yes I took a long break with YT, it feels good every now and then 😉👍
Looks like the plexy kickback shield prevents you from properly supporting the material on the binding side of the blade. And increasing the risk of kickblade. The desighn could really use a better safety mecanism.
It's true, this saw is good but I find it dangerous because there is no safety. In another video I changed some thing and now this saw is much better 😊👍
It was so good to watch and hear your intro again.
If you were to mount your cutting deck upon extended uprights, could you perhapd end up with a more conventional saw height without making the machine too top-heavy?
Hello Del, how are you ? good I hope. You had the same idea as me 😉 I have almost finished improving and especially making this machine more secure, I would make a video to show how I did. Hope this helps people who have the same circular saw 😊👍
@@satorrotas I'm very well, thank you, Pascal. It's very good to know that you're okay too.
I think it is irresponsible to retail this machine with such a low cutting deck. It really is unsafe, especially for inexperienced users.
@@Del350K4 That's right, I do not recommend buying this machine, the best is to take a more expensive one with the possibility of adjusting the blade in height and a cover for the blade, it is a minimum of safety. Although these machines, whatever they are, are always dangerous 😊👍
Yes a video, been a long time since the last. Wow that's a finger chopper, so many ways to cut oneself. I'm with you covers on the 3 sides, the guide is very loose could be better. Then no blade adjustments that could have been done like a Skil saw. The sander disc a direct mount better as it seems so far from the table and no surface in front for a flat sand.
Yes a lot of things to improve on this circular saw, I find it really dangerous, I regret having bought this model but now that it is here I have to find solutions, because my fingers are much more important than this machine. I will make another video to show what I have improved hoping it helps people who have this circular saw. Thanks for your great comment, have a good day my friend 😊👍
Hello Pascal glad to see you have returned i think this is a pretty handy machine but should definitely have a guard that covers the blade completely like a full size table saw does especially if it runs when running the chuck i have looked at these also I would like to have a small chop saw for brass and aluminum stock
This table saw comes with other blade for plastic, brass and aluminum which will be good for my constructions. But before, you really have to do more safety, I have already started and I would do another video on this circular saw once the job is finished. There is also the part where there is the engine which is not protected, and the tools come to magnetize on it which is also very dangerous. But once securing this machine will be really very practical 😊 Thanks for watching and good comment my friend 😊👍
Looks like a useful tool for what it is. Good luck hope you get the dust under control 👍🏼👍🏼
I am going to improve this machine and it needs to be more secure, but this little machine will be very useful. Thanks for your great comment chris 😊👍
Awesome little machine, i call these saws “widow makers” hahaha, i have had so many close calls with my fingers and bits of wood come flying back, everytime i counted my fingers after using it 😅 great video my friend 👍🏻
It's a nickname that fits this machine very well 😁 I have to improve it because I find it really dangerous. All these kinds of machines are dangerous but I find that this one there more particularly. I started the work to improve it, I would use it once I'm done. Have a nice day Harley 😉👍
Let me preface with, all saws are dangerous. That said, are these mini saws really that bad? I was thinking of getting one. Is it a bad idea to buy one ?
Waoo meja gergaji mini multifungsi rekomendasi untuk membuat kerajinan tangan
Terima kasih telah menonton dan atas komentar Anda yang luar biasa 😊👍
@@satorrotas sama-sama kawanku semoga saya bisa mendapatkan ilmu setelah mengikuti konten anda 🙏
@@EclaWood 😊👍
Very nice mini tool for the hobby, you need to hold it with clamps to the table and use a wood block as a support for the sanding disck 🔵🔵🔵👍👍👍✔️✔️😀😀🔵🔵🔵
Thank you for your advice carlos, but before using this machine I must secure it, as it is I find it too dangerous. Thanks for your great comment my friend 😊👍
Bonjour, pouvez-vous me dire la marque de votre scie miniature et où vous l'avez achetée, s'il vous plait. le montage est-il compliqué ? Merci de votre réponse et bon weekend.
@@dominiquebodeau298 Bonjour, il n'y a pas de marque pour cette scie. Je l'ai acheté sur le site banggood et il n'y a pas de montage spécifique. Mais attention car elle n'a aucune protection de lame et c'est très dangereux. Vous pouvez en trouver sur Amazone ou autre site dans les mêmes tarifs a peut prêt avec une protection ce qui a mon avis est plus prudent. Bon weekend à vous aussi 🙂
@@satorrotas ah d'accord, merci de votre conseil je vais aller voir sur amazon , en même temps j'ai déjà une scie électromagnétique, peut-être que ça ferait double emploi ?
Si vous avez une scie électromagnétique je suis pas sur que la scie circulaire vous soit très utile, a moins que vous vouliez couper des section plus importante, mais dans ce cas il vous faudrait une scie circulaire avec la lame qui ce règle en hauteur et je pense que ce serait bien plus cher 😊
@@satorrotas bonjour. Merci pour votre réponse. Et vos conseils. Du coup je ne vais pas investir dans une autre scie. Passez une bonne journée. Dominik
@@dominiquebodeau298 de rien c'était avec plaisir, bonne journée à vous 🙂
That is a very cool multy function machine I like it but they fact that there is no protection on the cutting disc and the depth is not adjustable that would but me off .
Glad to see you back 😊
Yes, this machine will make my work easier, but first I have to improve it and especially find a solution for the height of the blade. This circular saw is not secure and it is dangerous. I started work on it, I will make a video, hoping to help the people who have this machine. Thanks for your good comment my friend 😊👍
good job 👍
Thank you so much 😊👍
sympa, pour la decouple et le ponçage
Oui vraiment super comme machine 😊👍
Like you say definitely needs some improvements. But after that should make a fine Little table saw. Do you have a link for it?
Great work again my friend👍🏼😁
I bought this circular saw from Banggood but I have seen others cheaper and better secure on Aliexpress, I do not recommend this machine because it is not secure at all. I would do another video on this machine once I complete the safety job. But it is sure that this circular saw will facilitate my work for my constructions 😊 Thanks for your good comment my friend 😊👍
salut😁👋, sa fait un bail😅. dsl🙏.
mais sa fait plaisir de retrouver tes video👍👍. par contre tu es sur que c'est en vent libre ce truc😱. enfin surtout la scie. le coté ponceuse dremel me plais bien🤩.
merci du partage et á bientot, bonne soirée Pascal😃✌✌
Il est certain que l'on ne pourrait pas acheter ça en France, c'est vraiment pas sécuriser, donc avant de m'en servir je vais trouver des solutions pour l'améliorer. Merci pour ton commentaire, passe une bonne journée Marco 😊👍
Hola Pascal Amigo 👋. Me alegra mucho saber de ti 💪. Buena maquina, se puede hacer de todo 👌y para tus trabajos se vé genial 👍. Que pases un buen día 💃Un saludo cordial desde España 😎🚗💨💨💨🤝💨💨🇪🇸
Hola Miguel como estas, bueno espero. Muchas gracias por tu excelente comentario. Ten un buen día mi amigo 😉👍
@@satorrotas 🤜💥🤛👍😉
Now I understand better why you upgraded this machine, it was really too dangerous. It is very practical and it does not take up space but in terms of security it was really not at the top.
Very buy and great video 👍
Thanks for your very good comment and compliment Arsene 😊👍
@@satorrotas 😊👊
Building a jig/sledge to sit on top of the unit would give a zero clearance cut and also lessen the height of the blade.
Do you have a link for this model please?
This is what I did with also a protection for the blade 😊 if you want to watch the video, here is the link:ruclips.net/video/r8njyeozcPk/видео.html
I had bought it on Banggood, but it is no longer there. On Aliexpress you have the same kind of model 😊👍
Hey Pascal I wanted to let you know Stevo D passed away and I will try and get that camper out one day this week been super busy stay safe my friend 🤟🏼
I am so sorry to hear this sad news, all my best thoughts will go to his family 🙁 No problem, work comes first, very happy to hear from you, take care of you and your family Travis.
NEVER use the fence and the mitre guage together on any scale of tablesaw. One or the other. Never both. Cheers.
Very good advice, thank you 😊👍
@@satorrotas You're very welcome. Look at 'tablesaw kickback' on YT. It makes perfect sense, and will keep you SO much more safe. Cheers.
Thanks. I just watched two videos on tablesaw kickback, it's very informative. They are very dangerous machines, I don't use them often but I try to be very careful when I work with them.
Not going to read all the comments to see if the following was covered:
I own one of these saws, do
not know why because it is clear #1 the blade height can not be adjusted.
#2 The miter slide wobbles in the slot in the table. Far too much clearance. (On my unit my factory supplied miter is different then what is shown in the video)
#3 WORSE THING: The table top is attached to the base using ONLY four threaded TUBES . Nothing else supports/OR ALIGNS the top plate to the blade.
All it takes is for one of the attching screws to loosen and the top plate WOBBLES and distroys alignment between blade and miter.
I use this saw for model making, it was a waste of money. (Have not used the attachments supplied woth the saw)
Certain subject has been discussed, but it is certain that if we want security this is not a machine that I would recommend to people, it is better to pay a little more and have good equipment 😊👍
How to use the extensible tool
Hi. The extendable tool is used instead of the sanding disc, you need to put on the drill chuck and put in the extendable tool.
Hola Sator qué bueno saber de ti nuevamente espero y te encuentres bien de salud,😎 y que buena herramienta para tus trabajos, muchas felicidades 👍
Sí, todo está bien aquí, mis vacaciones terminaron, lástima que fue bueno no hacer nada 😄 Gracias por tu gran comentario, que tengas una buena semana para ti y tu familia Victor 😉👍
@@satorrotas muchas gracias, igualmente para ti 😀
@@VictorBarajasrc 😉👍
👍 👍
Merci beaucoup mon ami 😊👍
nice sharing buddy.
Thank you so much my friend 😊👍
Nice little tool
Thank you so much 😊👍
nice tool👍
Thank you so much Seven 😊👍
Ha ha cool, I observe that you could do a brushless conversion quite easily.
😄 I will especially improve this machine to keep my fingers in good condition 😁
The slider protractor should be facing you. It is backwards
Thank you, but you should have watched until the end of the video, you would have seen that I put them back in the right direction 😉👍
Mini table saw 👍👍👍👍👍
Thank you so much 😊👍
The miter box is not assembled right.
If you are talking about the pusher for wood, watch the end of the video I put them in the right direction.
Excellent
Thank you so much my friend 😊👍
Buena maquina, te facilitara bastante la construccion de tus dioramas.👍🏾
Voy a mejorar esta máquina y necesita ser más segura, pero esta pequeña máquina será muy útil. Gracias por su gran comentario mi amigo 😊👍
I ORDERD ONE but it has 1 cutting blade only not three instead iwas sent set of tiny tools i did not asked for
Sorry for you, I think it's a mistake, you need to file a complaint or you bought this table saw.
Hello Pascal. Handy machine for a handy man,but be careful,it can be dangerous as you say. Conclution...not for me..hahaha
I will improve this little machine, because as you say it is too dangerous as it is. It is certain that this will help me a lot for my dioramas, but it will only be useful when I have all secured. Thanks for your good comment, have a great day Jan 😉👍
@@satorrotas Samme to you Pascal, i look forward to see how you secure it. Thumbs up 🎮👍
Thanks Jan 😊👍
Saw disc outer and hole size
Size of the disc 12 centimeters, the hole is barely larger so no possibility of putting a larger disc.
Well Pascal. First of all it is great to see you back in action.. :) I have to agree with your review on this machine. Has a lot of awesome features but (in my opinion) no real thought went into actually making it. You of course have found all the issues with this machine. Unfortunately it is not a matter of "if" you will get hurt on this. It's a matter of "when". With the belts all exposed under there as well. YIKES. Thanks for sharing bud and again great to see the name pop up in the videos.. :)
You are right, I must be very careful with this machine, my fingers are the most important. I have to improve it because I find it really dangerous. All these kinds of machines are dangerous but I find that this one there more particularly. I started the work to improve it, I would use it once I'm done. Thanks for your great comment, have a good day Nick 😊👍
I guess this product doesn't have a height adjustment - which is why you are cutting a 1 inch tall piece of wood with the blade at 1000 inches
That's right, I did not pay attention when buying this machine that the blade was not adjustable in height which is really a shame and dangerous I find.
I think you have the mitre gauge backwards. LOL!
Thank you, but you should have watched until the end of the video, you would have seen that I put them back in the right direction 😉👍
I would simple remove the saw blade when not in use.
It's an good idea, but I'm not sure that the screw that holds the saw blade is of good quality, so I prefer to leave it in place and make a cover for the blade 😊👍
bonjour like bonne video gg
Merci beaucoup Tony 😊👍
Sad - you have a ruler that one cannot tell whether it measures in inches or centimetres or what
French measurement therefore in centimeters
I've never seen such a small table saw. It has so many other options included. I can see, you need to work with safety in mind. It looks fairly heavy duty. Yes, they should have covered the sides as much for safety as keeping the area clean. You have a good plan going forward👍Like 54
It's a good mini circular saw but not enough safety, I made another video on this saw to show how I secure them, now it's much better. Thank you very much for your excellent comment 😊👍
I wish I could have hear the sound of the machine, instead of some arbitrary music.
I didn't think the noise of the machine would please anyone, sorry
I do not see any lubricant deposit.
Because there is none.
It's probably a good idea to leave all the extra attachments, sander, etc., off while using the saw. It's dangerous enough without having another thing to bump into while cutting.
That's right, you're absolutely right. It is a machine that requires attention and above all taking all the necessary safety precautions.
Sorry pal but it seems to me that you need a bigger piece of kit for the larger pieces you want to cut !!!!
It is certain and I agree with you, but I only use this saw for my dioramas. It is obvious that for heavy work one would need one on feet and which are intended for the work of large pieces of wood.
What is the name of the model? Why is it not in descr or title? Awful.
Simply because it has no name, apart from "mini table shaw". I give you the link, you can check for yourself :
usa.banggood.com/Multifunctional-Small-Cutting-Mini-Table-Saw-DIY-Woodworking-Angle-Table-For-Metal-Cutting-Carving-p-1891048.html?imageAb=2&cur_warehouse=CN&ID=47184&rmmds=search&a=1658586007.8056&DCC=US¤cy=USD&akmClientCountry=FR
In the hospital yet??
😄😄 No and it won't happen. I made several modifications to make this machine safer 😉
NOT A TOY!
Yes, it is really not a toy, in addition as it is this machine is dangerous, I will have to improve it 😊👍
reviews have spoken words not music
👍
So what make and model is it? Basic information completely missing! 😳👎
Really useless comment and really not nice, first hello, then if you had watched the video in full you would have seen that this machine comes from banggood and that there is no brand. Furthermore, when someone asks me for more information on this or that thing, I answer them with courtesy. Have a good day anyway
Video muy largo y aburrido. No llegué a ver ni un minuto.
No obligo a nadie a ver mi video. Puedes guardarte tu comentario desagradable para ti.
Странный какой-то пользователь! Зачем обязательно надо одновременно и Патрон и пильный диск использовать? Сними параллельный упор и режь рейки любой длины. Сними транспортир и оставь параллельный упор и режь фанеру!
Станок продается так, я сделал еще одно видео, где преобразовал этот станок, убрал патрон, который бесполезен, сделал режущую пластину большего размера, оставив направляющую. Это машина для небольших работ, и она не имеет безопасности. Но для того, что я хочу сделать, этого вполне достаточно. Спасибо за ваш комментарий 😊👍
No more sign language if you lose a finger! Which in that case is almost like losing your tongue!! 😛🩸🩸🩸
I agree with you 😁