Wow thank you I've been up and down fighting my car testing checking and changing parts. Went and re soldered the ecu on a few parts that didn't have much to any solder and ones that looked cracked. And wish I would have seen this. Would have went and grabbed a new transistor for c17 and been back in business. Thank you so much
Friend, I have 2 ECUs, P0B-A01 Accord LX M/T. Both times I replaced all the capacitors with the correct specifications. One of them, when I turn on the ignition, the car has the injection light on for about 3 minutes and if I try, it won't start. After 3 minutes it turns on and the injection light comes on indicating error 9. The other central, sometimes the car starts perfectly and the injection light does not appear. But sometimes starting is very difficult, you have to press the key a lot and step on the accelerator. What do you say about each of these ECUs? Help me please. Tks
How do I fix the memory problem? Have one with solid cel. Primes and car starts, the cel is just solid and can’t get any flashes when it is jumped. TIA
Hello, my ECU P30 of the del sol doesn't provide the GND to all injectors, do you have any ideas what reference can i check on the ECU for fix it? Thank you !
I have a ecu that is chipped with s300 and the cel comes on right away with cyclinder 1 code. When I had the changed the board the another ecu the check engine light went away. What will cause a cyp code? Possibly bad capacitor
My 95 Civic has a ECU issue, the fuel pump won't start, this happened a year and half ago, the ECU was repaired, but yesterday the same problem came back. Any suggestions with what's causing this problem?
Hello, I have problem with chipped p28, when i turn off car 3 dashboard lights start barely lighting(engine, battery and oil), even if i take the key off from ignition switch. Car runs perfectly. Do you know this problem? With my original ecu p9k i don't have this problem. It looks like shorten circuit on ECU, but it looks fine
I turned on the engine check when I stopped to refuel. it lights up and does not go out, it stays on. I tried to make a diagnosis but the light stays on and does not make a diagnosis. I changed ecu and again the same. it does not turn on the petrol pump, nor do I have an ignition at the start. I decked the petrol relay and my pump is working. whenever the gas pump works. the distributor is functional what is the problem ??? all fuses are good
I have a d16z6 full stock. Recently replaced the capacitors with same specs correct polarity and proper soldering( checked 2x). All running properly but sometimes the CEL pops out. I cannot read any codes after switching off it goes away. If anyone has any suggestions please help. The car runs but I'm not sure why this happens.
Hey man i need a little help. thank you so much for this video, i had 2 ecus like this my ecu i changed myself worked just fine. The second one was a friends but had delayed fuel prime. told him the ic17 power supervisor needed replaced to send it back to where he just got the ecu. well they changed the ic17 and now it has solid cel but does prime and start. Runs like crap. Any ideas what this could be so i can fix it?
When j1 is mounted fuel pump does random things turns on and off solid cel and engine misfires and wont even startup When j1 is cut i have solid cel But pump primes engine starts and I can drive it normally
So show us the easiest/best way to remove ic17.. I chip as well but am now coming across having to remove ic17 and so far… can’t get all of the solder out without burning the pads…
I’m having a issue where I hear the fuel main relay click but the fuel pump won’t prime Check engine light goes off as soon as the main relay clicks my car cranks but doesn’t start
Hi! Got sólid cel with no fuel prime , already changed ic17 and all caps and still the same! Already changed caps on other ecus and worked fine! So its not soldering problems... Any tips? Maybe ic12 is damaged?
No power on Q10 pin 1 indicates a bad +5VDC reference - which would affect other things than just fuel pump .The solder joint at Q10 pin 1 could be corroded or damaged with age.if it doesn't work change QM3
@@perrikdesrocers4507 it was definitly the qm3 … now it primes but dumps a lot of fuel… Till the car shuts off… j11 cutted so no external eprom… help? 😅
@@metrogp also if your ecu is chip cut j1 and see first it injector will stay open first . And tell me if you have a solide sel and if not do you have any check engine codes
Great information, I have a P06 that’s running a b20 in a 2000 civic coupe I have a solid CEL and the motor starts and runs (fuel prime) rips actually, full throttle feels great but it bucks at the lower RPMs, I have swapped to other ECUs (obd2) and it runs also with no solid light so I can confirm it’s my obd1 computer but what I’m wondering is will the car still run with a corrupted memory chip? I would assume when an ecu goes bad it wouldn’t run and drive which it does but I cannot tune anywhere around the idle or even 2k rpm and lower it just cuts out and acts like a tps is malfunctioning, I’ve been needing to chip the 28 pin anyway for the b20, is it possible I can get two birds stoned at once and chip my computer (more optimized) and get rid of my solid CEL ?
@@YayaAndCars thanks so much for the reply. I did in fact confirm online that is what the code is for. But I’ve never had that issue before. It’s only this ecu telling me that code. I’m so confused 😵💫
Wow thank you I've been up and down fighting my car testing checking and changing parts. Went and re soldered the ecu on a few parts that didn't have much to any solder and ones that looked cracked. And wish I would have seen this. Would have went and grabbed a new transistor for c17 and been back in business. Thank you so much
Thanks bro, in my case i change all the capacitors and doesn't works and after that i change the IC17 and that resolved the problem!🙌👌👍
Friend, I have 2 ECUs, P0B-A01 Accord LX M/T.
Both times I replaced all the capacitors with the correct specifications.
One of them, when I turn on the ignition, the car has the injection light on for about 3 minutes and if I try, it won't start. After 3 minutes it turns on and the injection light comes on indicating error 9.
The other central, sometimes the car starts perfectly and the injection light does not appear. But sometimes starting is very difficult, you have to press the key a lot and step on the accelerator.
What do you say about each of these ECUs?
Help me please.
Tks
How do I fix the memory problem? Have one with solid cel. Primes and car starts, the cel is just solid and can’t get any flashes when it is jumped. TIA
I need the answer to this as well ☹️
Me too
Same
Hello, my ECU P30 of the del sol doesn't provide the GND to all injectors, do you have any ideas what reference can i check on the ECU for fix it? Thank you !
I have a ecu that is chipped with s300 and the cel comes on right away with cyclinder 1 code. When I had the changed the board the another ecu the check engine light went away. What will cause a cyp code? Possibly bad capacitor
It would be safe to change them as a precaution, but it could be the HIC modul (the two long vertical PCB), it is responsible for these sensors
Have any tips for fixing CEL 9? Ecu has replaced capacitors and ic17. Thanks 🙏🏽
H1C1 daughter board has more then likely failed.
if its no spark, n the culprit is ecu, which part in the circuit board cause the problem? thank you.
It's the ignition transistor q38 I think
Good morning, what are the capacitors of the iac valve
My 95 Civic has a ECU issue, the fuel pump won't start, this happened a year and half ago, the ECU was repaired, but yesterday the same problem came back. Any suggestions with what's causing this problem?
did u fix it?
Hy...my problem is car normally run and idle ...but just solid cel...check mil also solid cel ..so problem in eeprom???
Nup it the ic17
@@YayaAndCars ic17 for fuel pump??...my car normal use ... Just solidcell...
Yep it can manifest itself as this
Hello, I have problem with chipped p28, when i turn off car 3 dashboard lights start barely lighting(engine, battery and oil), even if i take the key off from ignition switch. Car runs perfectly. Do you know this problem? With my original ecu p9k i don't have this problem. It looks like shorten circuit on ECU, but it looks fine
did you solve it?
I have replaced the capacitor, but the problem is still not resolved. Do i have to replace the ic 17 too?
Yep most certainly
@@YayaAndCars ic 17 must be programmed or just replace it?
@@panduraga did replacing ic17 work?
thanks, useful information
You are welcome ☺️
Great info, thank you :)
code 14 changed iacv light still on so my chip is corrupted?
Check your harness continuity with a multimeter first
I turned on the engine check when I stopped to refuel. it lights up and does not go out, it stays on. I tried to make a diagnosis but the light stays on and does not make a diagnosis. I changed ecu and again the same. it does not turn on the petrol pump, nor do I have an ignition at the start. I decked the petrol relay and my pump is working. whenever the gas pump works. the distributor is functional what is the problem ??? all fuses are good
Did you check the main relay?
Hey my ECU ground has power but the other pin doesn’t ground for the fuse box…15amp…. Checked everything else
I have a d16z6 full stock. Recently replaced the capacitors with same specs correct polarity and proper soldering( checked 2x). All running properly but sometimes the CEL pops out. I cannot read any codes after switching off it goes away. If anyone has any suggestions please help. The car runs but I'm not sure why this happens.
hey, did u repair it?
my car takes long time to prime is that a capcitor or memory issue? P06
Most definitely the capacitor, and with time it will burn the ic17 completely, get new caps as soon as possible
Hello i have cel code 11 im baffled what it is and car is under powered like choking
Hey man i need a little help. thank you so much for this video, i had 2 ecus like this my ecu i changed myself worked just fine. The second one was a friends but had delayed fuel prime. told him the ic17 power supervisor needed replaced to send it back to where he just got the ecu. well they changed the ic17 and now it has solid cel but does prime and start. Runs like crap. Any ideas what this could be so i can fix it?
did he fix it?
When j1 is mounted fuel pump does random things turns on and off solid cel and engine misfires and wont even startup
When j1 is cut i have solid cel But pump primes engine starts and I can drive it normally
So show us the easiest/best way to remove ic17.. I chip as well but am now coming across having to remove ic17 and so far… can’t get all of the solder out without burning the pads…
first remove as much solder as you can with desoldering wick or a small vacumpump, then use a smd rework hot air to fully desolder the ic17
Where should look if the ECU keeps popping fuses when ignition is switched on? Thanks
grounds
Thank you
I’m having a issue where I hear the fuel main relay click but the fuel pump won’t prime Check engine light goes off as soon as the main relay clicks my car cranks but doesn’t start
Also my ecu has a cut wire thing number j12 on the ecu p28
Check if the fuel pump is working, it looks like she is the culprit
Hi! Got sólid cel with no fuel prime , already changed ic17 and all caps and still the same! Already changed caps on other ecus and worked fine! So its not soldering problems... Any tips? Maybe ic12 is damaged?
No power on Q10 pin 1 indicates a bad +5VDC reference - which would affect other things than just fuel pump .The solder joint at Q10 pin 1 could be corroded or damaged with age.if it doesn't work change QM3
@@perrikdesrocers4507 it was definitly the qm3 … now it primes but dumps a lot of fuel… Till the car shuts off… j11 cutted so no external eprom… help? 😅
@@metrogp qm1 and qm2 control injector
@@metrogp also if your ecu is chip cut j1 and see first it injector will stay open first . And tell me if you have a solide sel and if not do you have any check engine codes
@@perrikdesrocers4507 sólid cell, injector stuck j1 cutted still the same , no codes
Hi, i have a problem with p30 ecu. I don't have spark, already changed q38 transistor but still no spark
did you fix it?
@miziaa Unfortunately nope. I'm still looking for someone who can fix these ecu.
@@andreact88 did u try to put another ecu?
@@miziaa yes, car works perfectly.
Great information, I have a P06 that’s running a b20 in a 2000 civic coupe I have a solid CEL and the motor starts and runs (fuel prime) rips actually, full throttle feels great but it bucks at the lower RPMs, I have swapped to other ECUs (obd2) and it runs also with no solid light so I can confirm it’s my obd1 computer but what I’m wondering is will the car still run with a corrupted memory chip? I would assume when an ecu goes bad it wouldn’t run and drive which it does but I cannot tune anywhere around the idle or even 2k rpm and lower it just cuts out and acts like a tps is malfunctioning, I’ve been needing to chip the 28 pin anyway for the b20, is it possible I can get two birds stoned at once and chip my computer (more optimized) and get rid of my solid CEL ?
Now thats what I'm talking about. It there anywhere a guy can get an actual schematic? Cheers
I used to have a detailed schematic of all the components of the ECU, have to check on my old files
@@YayaAndCars Hello friend, do you have the schematic that you can share with me please?
I have fuel prime, with CEL flashing code 21. (2 long cel flashes & 1 short flash) p06 with hondata S300
That's the obd1 code for VTEC solenoid valve malfunction it I'm not mistaken
@@YayaAndCars thanks so much for the reply. I did in fact confirm online that is what the code is for. But I’ve never had that issue before. It’s only this ecu telling me that code. I’m so confused 😵💫
Check if the ECU is correctly chipped, and also the condition of the vtec transistor, I believe it's ic13 or ic14
@@YayaAndCars will do, thank you 👍🏼
where 4-wire 02 is controlled on p28
The heater circuit is controlled by one of the 3 big circuit on the top left of the ECU , they are Darlington transistors
How do you fix fuel prime and solid cell?
Have you fixed it?
Could you trouble shoot my p30s? For a 1994 del sol
Tell me!?
Hey I have a
En français ça donne quoi ?
I have a p28, all capacitors are new but I get no injection on cyl 4 is it a ecu problem? The injectors are changed and the cables are new. Thank you
It is chipped
It's most likely one of the STA460c, they are the 3 long circuit on the top left of the ECU, they are responsible of powering the injectors