Thanks brotha 😬. I had no intention of making the video but after how complex it was I had to. Really hope it helps others since most will at one point or another need to replace the lcd screen.
Just wanna say a huge thank you from us over here at Fifth Dimension Minis, after a half hour frustrated watching the factory video on replacing the motherboard, I found this video.Turns out this video doubles as a perfect video for replacing your motherboard as well, as it’s a very similar process. Can’t thank you enough for this one 🙏🏻
Thank you! The 'I locked the ribbon backwards' tip was what ended up saving me! Prompted me to go check the old ribbon, and found I'd done it backwards where it meets the screen - the opposite end to what you had!
I was waiti8ng for you to finish to see if you mentioned the LCD cable going in upside down as I did the same thing. If you look closely at the ribbon cable one side of the plug end has a black tape over it and the other side has bare, silver connectors. The side with the black tape goes UP opposite the circuit board. If you put it in upside down the black tape will not allow the conductors to touch the pins on the plug... probably a good thing as it probably would damage some circuitry. Also, make sure to plug the Z axis stop into the correct socket on the mainboard. there are two sockets, side by side. My machine did not stop going down so i have to open it up and move it to the other plug. Pretty sure I go it into the wrong one! Fortunately I tested it with the build plate removed so I did not damage my new screen! One more thing; on mine the LCD screen cable had to plug in on both the board AND on the LCD panel so make sure it is oriented correctly there as well. To date my machine is still down. I have an early Saturn and have had to contact Elegoo support to find the right drivers for it.
Thank you so much for this informative video! I am going to be attempting to replace my screen this coming weekend on my Saturn 3 Ultra. This added so many little tidbits that weren't in the short Elegoo video. It just gives me a better idea of what to expect going in. Even the fact of trying to find out which screen my new one is before I even start putting it in.
First thing I did when I got my resin printer was to purchase an iPad Screen Protector and cover the printer's LCD screen with it - sealing the edges with Kapton Tape. Have not had any issues with my screen yet.
I love you so much right now. I was having an entirely separate problem with my Z-Axis and this video fixed it for me. I was able to see the correct orientation of the Z-Axis motor and that was my error.
I came here to find the right procedure. It's pretty amazing that the EXACT same thing happened to my Saturn S. I thought I had all the resin out and when I went to print a new print the old resin punched through the few film and broke the LCD.
quote " I thought I had all the resin out and when I went to print a new print the old resin punched through the few film and broke the LCD." SO if you used the Option CLEAN Resin tank or whatever is called , that ULTRA violet light illuminate the left overs of resin in your tank ,to get it Hard and then remote it more easily , then no accident would have happened?
did you also have to dowload the firmware from the "saturn" tab to match the screen? i tried to download the file from the Saturn S tab and it didnt work but theres warnings in the text to use the firmware that fits your printer otherwise it could cause damage so im scared to follow the specifications exactly like the video since i have a saturn S and not a saturn.
Just ordered a Saturn S, my first resin printer. Been watching videos on "need to know" items. I think this one will eventually come in handy! Thanks! Edit: I might just order a spare FEP and screen to have on-hand. Would beat waiting for a replacement if one or the other or both fails.
Thank you for the guide, in my case - it was the ribbon incorrectly has the black side against the board. i flipped it based on some of your observations, and it worked!
Thank you, It worked for me... This one was a lot harder than my Phrozen mini 4kd... After I ugraded the firmware I need to figure out the ribbon cable rigth positon for both, board and screen sides. After many tries it worked. I was worried about a posible damage to the new LCD but after watching yor video I knew where the problem was.
Day two with the Elegoo Mars 3 and I'm already replacing my second FEP film. Just had my first FEP puncture, and I think it's because I over-tensioned it during replacement. Inspecting the print surface, I had printed nothing- and I had maybe a dime's worth of hardened resin in the vat.
Great video. Have not have to replace either one on my Saturn or Mars 2 but am going to buy one for each for if and when they do go bad. Thank you for the info
Which direction has to get the the cable onto the board… I have the same like you and would afford to do the same mistake. Would be great if you could mention this next time 😅😬. Thank you
Thanks for the guide. Don't have to do it yet but still helpful i remember back in the anycubic photon days i had a a hole in the vat left and left resin on it for few days since i had a black enclosure i didnt see when resin leaked all over the printer and got in-between the screen. Had to replace it :(
Thanks for going ahead and making this video for us to go ahead and watch it to be able to go ahead and change our screens if the screen does go ahead and get damaged when something does go ahead and go wrong. I went ahead and smashed the like button and I will be going ahead subscribe to your channel because you do go ahead and give really good information. Haha. Im just kidding buddo. Thanks for the video😜😁😁😁
I just got a replacement LCD screen for my Elegoo Saturn, and I was wondering, should the screen be replaced if there's a dim light when using exposure or tank clean?
Ever since purchase the black tape has been suspect and eventually let go to allow resin into the printer case. And even when I replaced my LCD screen the new black tape is horrible and does not stick even after cleaning the recess which it would be stuck into. I need to locate new tape once I get a new Motherboard. During ribbon cable removal the cable latch broke off during flip up, and now the ribbon stopped connecting.
Okay so, overall quality and usability and longevity, Elegoo Anycubic or Creality for a resin printer? To make it easier, just pick the closest model each of the three has to the others so it's just one model from each company. I want to get one and I've narrowed my search down to one of these three companies.
Just finished installing my new screen. The ribbon cable has the same number as the screen that was on previously. I don't have the rectangle when testing exposure. I flipped the ribbon cable and I'm getting the same result. Did I get a bad screen or am I missing something?
I replaced the screen! Your video was great. Exposure test and screen worked fine the day and I put it in but the very next day only half the screen is working????
Hi, thank you for a helpful video. I have one question (because I don't have experience in the 3D printer field): I just need a digital mask and its controller for UV exposure purposes (I already have the light source), so is there any commercial package for that? and/or how to buy these components?
Thank you for the video. I almost this thing working but when I try to install the firmware it stops at about 80% and the confirm button comes on and tells me to restart the printer. So I do and then I run the exposure test. The screen is completely filled and the box doesn't come on. I checked the cables and they are install in the correct position. HELP
Hello. I have a Saturn S, but can’t find a replacement screen for the S specifically. Would this replacement work on mine? Same question for build tank.
When you say you "installed the ribbon cable backwards" Does the @10:00 mark show you installing it the correct way or the incorrect way? That is; the 50 pin closest to the side panel - is that correct?
Great video, In relation to having to upgrade the Firmware I ran into issues, turns out I had to Format the USB in a Windows machine, I did it previously on a Mac (FAT32) and never worked.
do you really need to remove the screen protector? I have screen protectors i bought from third party to prevent those nasty resin spills (exactly like the one you changed the lcd because of) that work amazingly. Maybe just remove the tab from the screen protector and leave it on?
Good video as always, I am planning on purchasing a Saturn in the future. I then looked at your '3d printing blog' , unfortunately it is a link to a scam site that gets your email ( 'for its marketing services) and pushes you into one of those 'Make 10 purchase's ' and we give you a prize. I don't know if this was your intention or somebody hijacked you blog site, but it was unappreciated.
Commenting here out of desperation. I have a Voxelab Proxima 6.0 2K mono. I assume the firmware procedure is the same, but when I go to "print" the firmware, the file does not ap[pear. I am out of ideas and have searched everywhre. Any suggestions?
Great video, bought my first resin printer yesterday so keep these videos coming. $99 Voxelab Proxima. So you took off that screen protector, is that simply because of the white bit, or is there a good reason to not have a screen protector on a resin printer? I was kind of thinking a screen protector from a tablet sounded like a good idea, one of the thin ones similar to the one you peeled off.
Some do keep it on and I have kept it on in some instances. For this I was really going by what elegoo recommended in their video. If there are no bubbles it shouldn’t be an issue to leave it on. That being said I have not done any tests to see if the extra film causes any sort of distortion on the print. It does not as far as I know.
@@jon9947 AFAIK you'll need to increase the exposure time so it can "significantly" increase print times as a result.. hence why they tell you to remove it as speed is a key selling point. So yeah +15-20 mins per 1000 layers is probably fine for most people if each layer is +1 second exposure.
Great video, i have a question regarding installing firmware. I was told that it wont install if you put it in a folder and has to be direct. thoughts?
Since these ARE expendables, one of the ways that a quality printer could differentiate itself from the competition would be to make these replacements MUCH easier.
This video was incredibly useful. I managed to replace the screen no problem, thank you. But the firmware.... no matter what I do I can't get that rectangle!
i have sla resin that has leaking onto the light and pcb, still works...trying to replace my screen right now... how would you suggest i clean the rest?
I installed my new screen into my saturn and worked for a couple days and then died. I'm not really sure what happened but half of the LCD was not working. Amazon is sending me out another one and based on this video i didn't do anything wrong. Has anyone else had this problem? If so, do you know what caused it? These screens are not cheap
I assume it's only if you touch the glass part, not the plastic part but I would be paranoid anyway. I have some experience with that, oddly enough not with my printer but with my projection TVs. Over the years I've replaced bulbs 6 times, 2 barehanded and 4 with cotton gloves. The first time I realized I briefly touched the glass with my bare finger but I went ahead anyway (what else could I do), bulb life 6 months. Next one with cotton gloves, 12 months! The third I didn't have gloves but I was extremely careful I didn't touch anything glass. That lasted 6 months only - I must have touched something and not realized it. The next 4 bulb changes, all with cotton gloves (the last one is still in), bulb life 12-13 months. That made me a believer! (Note: your projection TV bulb mileage will vary, I watch so many hours per year I need an intervention)
@@mikebare3677 Yes the oil on your hands can leave deposits on glass envelope of a halogen bulb and the extreme heat on that glass will cause that spot to become a weak area and it can fail. This is not the same situation as the LED and lens set up though. First of all the LEDs themselves are not susceptible to the same thing so you can touch them all you want it won't be a problem and the lenses aren't even attached to the LEDs in this case so it's doubly fine to touch them.
Actually you don't need to remove screen protector from the top side of the screen. That way it will protect the screen if the same thing happen again. It's completely transparent so it wouldn't affect the exposure nor print quality.
I have kept it on for other printers like the phenom but for this was going by the instructions from elegoo. But I agree as long as the tab can be removed it should not be an issue to keep it on.
Yes you need to. That screen protector has a film guard pull tab that helps it be removed. If you leave it, it’ll intrude on the print area. But the company does recommend you replace with a fep sheet so the principle stands just that screen protector specifically you need to remove
Several vendors make a screen to protect your lens: those are much larger than the lens itself so, if a leak or spill happens, those screens protect the taped sides as well as the top of the LCD. In case of a drip or spill you just replace the screen, the LCD is never in danger. A drip or spill is the reason I had to replace my screen - I leaked and didn't realize it for dozens of prints, and the resin was on there permanently. If I'd had one of those add on transparent screens, I could have replaced it instead of replacing the LCD (which I did, very expensive).
@@ModBotArmy lol i came here because i got a issue with resin bonding with the screen and see you pulling off the screen protector after learning the screen protector is built in on assembly.. im like NOOOOOOOOOOOOOO!! after seeing it lol
![[DOKKAN BATTLE] Worldwide Campaign Announcement Video Part 2!](http://i.ytimg.com/vi/JpT5Voak6WA/mqdefault.jpg)
Oh man oh man this is a super helpful video for folks out there!
Thanks brotha 😬. I had no intention of making the video but after how complex it was I had to. Really hope it helps others since most will at one point or another need to replace the lcd screen.
This one got us through our motherboard replacement as well!
Just wanna say a huge thank you from us over here at Fifth Dimension Minis, after a half hour frustrated watching the factory video on replacing the motherboard, I found this video.Turns out this video doubles as a perfect video for replacing your motherboard as well, as it’s a very similar process. Can’t thank you enough for this one 🙏🏻
Thank you! The 'I locked the ribbon backwards' tip was what ended up saving me! Prompted me to go check the old ribbon, and found I'd done it backwards where it meets the screen - the opposite end to what you had!
I was waiti8ng for you to finish to see if you mentioned the LCD cable going in upside down as I did the same thing. If you look closely at the ribbon cable one side of the plug end has a black tape over it and the other side has bare, silver connectors. The side with the black tape goes UP opposite the circuit board. If you put it in upside down the black tape will not allow the conductors to touch the pins on the plug... probably a good thing as it probably would damage some circuitry. Also, make sure to plug the Z axis stop into the correct socket on the mainboard. there are two sockets, side by side. My machine did not stop going down so i have to open it up and move it to the other plug. Pretty sure I go it into the wrong one! Fortunately I tested it with the build plate removed so I did not damage my new screen! One more thing; on mine the LCD screen cable had to plug in on both the board AND on the LCD panel so make sure it is oriented correctly there as well.
To date my machine is still down. I have an early Saturn and have had to contact Elegoo support to find the right drivers for it.
Thank you for this tip. With it I was able to properly connect my new screen.
Thank you so much for this informative video! I am going to be attempting to replace my screen this coming weekend on my Saturn 3 Ultra. This added so many little tidbits that weren't in the short Elegoo video. It just gives me a better idea of what to expect going in. Even the fact of trying to find out which screen my new one is before I even start putting it in.
I never want to say LCD again. Haha that being said I really hope this helps 😬.
First thing I did when I got my resin printer was to purchase an iPad Screen Protector and cover the printer's LCD screen with it - sealing the edges with Kapton Tape. Have not had any issues with my screen yet.
I used some bonus that I got with my Kindle, it also works fine
One the best 3dprint youtubers. Always providing great value in your videos. Thanks.
I love you so much right now. I was having an entirely separate problem with my Z-Axis and this video fixed it for me. I was able to see the correct orientation of the Z-Axis motor and that was my error.
I don’t own an Elegoo Saturn, but when The ModBot posts, I watch!
You rock! Hope you had a great Monday 😬
I came here to find the right procedure. It's pretty amazing that the EXACT same thing happened to my Saturn S. I thought I had all the resin out and when I went to print a new print the old resin punched through the few film and broke the LCD.
quote " I thought I had all the resin out and when I went to print a new print the old resin punched through the few film and broke the LCD." SO if you used the Option CLEAN Resin tank or whatever is called , that ULTRA violet light illuminate the left overs of resin in your tank ,to get it Hard and then remote it more easily , then no accident would have happened?
@@technoartfest8708 my favorite character on South Park is Captain Hindsight. He’s a hoot.
did you also have to dowload the firmware from the "saturn" tab to match the screen? i tried to download the file from the Saturn S tab and it didnt work but theres warnings in the text to use the firmware that fits your printer otherwise it could cause damage so im scared to follow the specifications exactly like the video since i have a saturn S and not a saturn.
Just ordered a Saturn S, my first resin printer. Been watching videos on "need to know" items. I think this one will eventually come in handy!
Thanks!
Edit: I might just order a spare FEP and screen to have on-hand. Would beat waiting for a replacement if one or the other or both fails.
Go ahead man, Go ahead! ;) Great vid!
Thank you for the guide, in my case - it was the ribbon incorrectly has the black side against the board. i flipped it based on some of your observations, and it worked!
OMG thank you so much! I was so confused. I had the same LCD screen as you and had the same problem.
Thank you, It worked for me... This one was a lot harder than my Phrozen mini 4kd... After I ugraded the firmware I need to figure out the ribbon cable rigth positon for both, board and screen sides. After many tries it worked. I was worried about a posible damage to the new LCD but after watching yor video I knew where the problem was.
Thanks for all your help. Fep film change and screen up and running.
I'm glad I'm not the only one that was missing the 4 screws and metal bar.
Man it's just one thing after another with this Saturn. Wish this stuff would just work
great tut walked me through my 1st screen swap and update ty
instead of triple checking or empty the vat, you can run the clean option and peal the cured resin in the bottom, that will save you time and paper.
thank you for this vid. made it easy to see a error in connectors I made
With PTFE lubricant, I got a FEP sheet to last 16 months after printing +100 prints on my Elegoo Saturn.
I am so glad you made this video! You helped me get my saturn up.and running again!
Hello can you tell me that the lcd surrounded box type board where the z axis also fitted is made of plastic or metal?
I owe you my life; I also accidentally installed the ribbon backwards and couldn't figure out what I'd done wrong until I watched this.
Day two with the Elegoo Mars 3 and I'm already replacing my second FEP film. Just had my first FEP puncture, and I think it's because I over-tensioned it during replacement. Inspecting the print surface, I had printed nothing- and I had maybe a dime's worth of hardened resin in the vat.
Big thanks! Great video and super helpful! subscribed!
Oh hey, this is the printer I bought less than 24 hours ago. This is probably a good watch.
Great video. Have not have to replace either one on my Saturn or Mars 2 but am going to buy one for each for if and when they do go bad. Thank you for the info
Thanks for the video! This helps a lot as I was about to replace my Saturn LCD screen!
Without you video i would have been lost 😪
Excellent video, well executed and informative!
Excellent video. Thank you for making it.
Love U man! You save my day!
Which direction has to get the the cable onto the board… I have the same like you and would afford to do the same mistake. Would be great if you could mention this next time 😅😬. Thank you
Great video but salvage everything you can always. I got no double sided kit or black tape in the official screen replacement.
You are a rockstar! Thx so much for this!!!!!!
Thanks for the guide. Don't have to do it yet but still helpful i remember back in the anycubic photon days i had a a hole in the vat left and left resin on it for few days since i had a black enclosure i didnt see when resin leaked all over the printer and got in-between the screen. Had to replace it :(
The video footage of you installing the cable is backward? or is that you putting it in correctly?
Thank you, nice and clean explanation
very helpful! thank you :)
Thank you so much! Excellent guide!
a huge thank you !
Thanks for going ahead and making this video for us to go ahead and watch it to be able to go ahead and change our screens if the screen does go ahead and get damaged when something does go ahead and go wrong. I went ahead and smashed the like button and I will be going ahead subscribe to your channel because you do go ahead and give really good information. Haha. Im just kidding buddo. Thanks for the video😜😁😁😁
Well done! Can I ask you which batch is your Saturn?
I just got a replacement LCD screen for my Elegoo Saturn, and I was wondering, should the screen be replaced if there's a dim light when using exposure or tank clean?
this was very helpful! Thanks so much!
Ever since purchase the black tape has been suspect and eventually let go to allow resin into the printer case. And even when I replaced my LCD screen the new black tape is horrible and does not stick even after cleaning the recess which it would be stuck into. I need to locate new tape once I get a new Motherboard. During ribbon cable removal the cable latch broke off during flip up, and now the ribbon stopped connecting.
I must replace the black tape, is it a normal black tape or which one i need to buy? thanks in advance
Okay so, overall quality and usability and longevity, Elegoo Anycubic or Creality for a resin printer? To make it easier, just pick the closest model each of the three has to the others so it's just one model from each company. I want to get one and I've narrowed my search down to one of these three companies.
thank you thank you! You helped me! I can install lcd.
I think I need to do this on a Saturn I bought second-hand. How do I tell if it needs doing or if there is still some life left in the existing LCD?
Just finished installing my new screen. The ribbon cable has the same number as the screen that was on previously. I don't have the rectangle when testing exposure. I flipped the ribbon cable and I'm getting the same result. Did I get a bad screen or am I missing something?
I replaced the screen! Your video was great. Exposure test and screen worked fine the day and I put it in but the very next day only half the screen is working????
Sounds like a loose ribbon cable. I would reseat both ends 👍
Hi, thank you for a helpful video. I have one question (because I don't have experience in the 3D printer field): I just need a digital mask and its controller for UV exposure purposes (I already have the light source), so is there any commercial package for that? and/or how to buy these components?
Thank you for the video. I almost this thing working but when I try to install the firmware it stops at about 80% and the confirm button comes on and tells me to restart the printer. So I do and then I run the exposure test. The screen is completely filled and the box doesn't come on. I checked the cables and they are install in the correct position. HELP
Thanks!
your amazing thank you
Hello. I have a Saturn S, but can’t find a replacement screen for the S specifically. Would this replacement work on mine? Same question for build tank.
Life saver
Do you have a video how to update a Saturn firmware? Please
When you say you "installed the ribbon cable backwards" Does the @10:00 mark show you installing it the correct way or the incorrect way? That is; the 50 pin closest to the side panel - is that correct?
Great video,
In relation to having to upgrade the Firmware I ran into issues, turns out I had to Format the USB in a Windows machine, I did it previously on a Mac (FAT32) and never worked.
Is it only me that does the "... right into today's video" arm move on every single episode. I feel dumb but can't help myself.
what if the screen is scratched, but not broken? will i still need to replace?
do you really need to remove the screen protector? I have screen protectors i bought from third party to prevent those nasty resin spills (exactly like the one you changed the lcd because of) that work amazingly. Maybe just remove the tab from the screen protector and leave it on?
Good video as always, I am planning on purchasing a Saturn in the future. I then looked at your '3d printing blog' , unfortunately it is a link to a scam site that gets your email ( 'for its marketing services) and pushes you into one of those 'Make 10 purchase's ' and we give you a prize. I don't know if this was your intention or somebody hijacked you blog site, but it was unappreciated.
Commenting here out of desperation. I have a Voxelab Proxima 6.0 2K mono. I assume the firmware procedure is the same, but when I go to "print" the firmware, the file does not ap[pear. I am out of ideas and have searched everywhre. Any suggestions?
Great video, bought my first resin printer yesterday so keep these videos coming. $99 Voxelab Proxima.
So you took off that screen protector, is that simply because of the white bit, or is there a good reason to not have a screen protector on a resin printer? I was kind of thinking a screen protector from a tablet sounded like a good idea, one of the thin ones similar to the one you peeled off.
Some do keep it on and I have kept it on in some instances. For this I was really going by what elegoo recommended in their video. If there are no bubbles it shouldn’t be an issue to leave it on. That being said I have not done any tests to see if the extra film causes any sort of distortion on the print. It does not as far as I know.
@@ModBotArmy Thanks! Iv got an old tablet screen protector laying around some place, I'll give it a try.
@@jon9947 AFAIK you'll need to increase the exposure time so it can "significantly" increase print times as a result.. hence why they tell you to remove it as speed is a key selling point.
So yeah +15-20 mins per 1000 layers is probably fine for most people if each layer is +1 second exposure.
where did you order this black tape? Tnx
What does Power cycle mean?
I still can't tell which side is up and which side is down on the screen. Or which way the ribbon is supposed to be connected to the screen. 😕
Great video, i have a question regarding installing firmware. I was told that it wont install if you put it in a folder and has to be direct. thoughts?
What tape did you use to secure the LCD panel. I have heard Kapton tape but mine seem to have some kind of vinyl tape. So I an not sure what to bu8y.
Since these ARE expendables, one of the ways that a quality printer could differentiate itself from the competition would be to make these replacements MUCH easier.
How can i check my touch screen ? It keeps blank
This video was incredibly useful. I managed to replace the screen no problem, thank you. But the firmware.... no matter what I do I can't get that rectangle!
The Elegoo support team have helped me sort it! Result!
Hello can you tell me that the lcd surrounded box type board where the z axis also fitted is made of plastic or metal?
The orange part? Yes that's metal.@@Saim-fd5ir
i have sla resin that has leaking onto the light and pcb, still works...trying to replace my screen right now... how would you suggest i clean the rest?
elegoo saturn
D: not working for me.... replaced for a new one screen and stills no working :( just asked elegoo support....
LCD screen?
what about saturn s?
I installed my new screen into my saturn and worked for a couple days and then died. I'm not really sure what happened but half of the LCD was not working. Amazon is sending me out another one and based on this video i didn't do anything wrong. Has anyone else had this problem? If so, do you know what caused it? These screens are not cheap
I use the tank clean feature if I have even the slightest bit of evidence of a failure.
I can't imagine touching the plastic lens on top of the LED would cause the LED to burn up more quickly.
I assume it's only if you touch the glass part, not the plastic part but I would be paranoid anyway. I have some experience with that, oddly enough not with my printer but with my projection TVs. Over the years I've replaced bulbs 6 times, 2 barehanded and 4 with cotton gloves. The first time I realized I briefly touched the glass with my bare finger but I went ahead anyway (what else could I do), bulb life 6 months. Next one with cotton gloves, 12 months! The third I didn't have gloves but I was extremely careful I didn't touch anything glass. That lasted 6 months only - I must have touched something and not realized it. The next 4 bulb changes, all with cotton gloves (the last one is still in), bulb life 12-13 months. That made me a believer!
(Note: your projection TV bulb mileage will vary, I watch so many hours per year I need an intervention)
@@mikebare3677 Yes the oil on your hands can leave deposits on glass envelope of a halogen bulb and the extreme heat on that glass will cause that spot to become a weak area and it can fail. This is not the same situation as the LED and lens set up though. First of all the LEDs themselves are not susceptible to the same thing so you can touch them all you want it won't be a problem and the lenses aren't even attached to the LEDs in this case so it's doubly fine to touch them.
Actually you don't need to remove screen protector from the top side of the screen. That way it will protect the screen if the same thing happen again. It's completely transparent so it wouldn't affect the exposure nor print quality.
I have kept it on for other printers like the phenom but for this was going by the instructions from elegoo. But I agree as long as the tab can be removed it should not be an issue to keep it on.
It will not save your screen mine broke from the glas
Yes you need to. That screen protector has a film guard pull tab that helps it be removed. If you leave it, it’ll intrude on the print area. But the company does recommend you replace with a fep sheet so the principle stands just that screen protector specifically you need to remove
Several vendors make a screen to protect your lens: those are much larger than the lens itself so, if a leak or spill happens, those screens protect the taped sides as well as the top of the LCD. In case of a drip or spill you just replace the screen, the LCD is never in danger. A drip or spill is the reason I had to replace my screen - I leaked and didn't realize it for dozens of prints, and the resin was on there permanently. If I'd had one of those add on transparent screens, I could have replaced it instead of replacing the LCD (which I did, very expensive).
Does the direction of the ribbon matter or just which way its flipped?
Dude my printer shipped with. A bad screen and now it’s shit the bed completely… I’m hoping it’s not the board
Can you leave the screen protector on?
Some do. You can start with it in and if you have any issues remove it afterwards 👍
@@ModBotArmy lol i came here because i got a issue with resin bonding with the screen and see you pulling off the screen protector after learning the screen protector is built in on assembly.. im like NOOOOOOOOOOOOOO!! after seeing it lol
I didn't crack my screen but it just stopped printing. I haven't put thousands of hours of print time on it. Maybe 50 hours
it appears they sent me the wrong screen...
I would say you said 1337 times LCD Screen in the video xD but i am bad in Counting xD
You need a quarter jar for every time you say LCD screen
Lmao it wasn’t evident when recording but after editing it and watching it like 10 times I realized I said lcd way to many times 😬
I just got my printer are you trying too jinx me
Thanks!