Just decided to get my drone ready for the weekend and the remote started Wiggin out so I went right to RUclips and searched. You came up right away. It worked for me. No more beeps. Updated firmware. All good for now. Thank you.
Thank you kind sir for taking the time to make this video. Absolutely love your content. I have the Mavic Air 2 and hoping to upgrade to Air 2S real soon.
.I cannot thank you enough for this video. Your instructions worked on a Phantom 4 ver. 20 The screen prompts in the software do not mention the dial. They only mention the joy sticks so I could not get it to calibrate until after I watched your video. Thank you!
....Problem started in the car.... In my case this problem also starts while I switch on the control while inside the car. But your fix solves the error/beeping. Thanks!
Hello and thank you so much for your video. One question I have :how will be possible that controller receive the voice when you are spiking during drone is flying?
Yea it works. I don't understand what made it start beeping like that in the first place . Mine started doing that 2 days ago. And I've had it for 4 or 5 months now.
I've never experienced this until just today when I finally updated the firmware. So I'm guessing it's a firmware bug? I actually got it to shut up by switching the flight mode switch back and forth. I then finished all my updates and decided to recalibrate the control anyways, even though the beeping had stopped.
My control never says: callibration successful, I tried for more than 20 minutes, but nothing happened, what can I do??? (I have the firmware up to date)
thx for advice. It works as well on MA2 maybe it is caused by too often using funkction Low R Low L to turn on/off propellers. I had this issue but durring flight it sileced itself. After landing and swaping batteries problem occurs again. Until Your vid, thx.
The beeping was driving me crazy... But I did an update while this thing beeping, powered off and it back on, but it was still making the beeping noise. Saw I note sayi g RC calibration needed... Attempted to do it but then it stop 😳... Without me doing the calibration... BUT just incase... I went in and did the calibration anyways... Thanks for the vid
I just got the air 2s yesterday. when you calibrating remote control and move the sticks you have to move them until the lines turn green at 100% You have to move the sticks in the direction of the arrows until the lines turn green and the same goes for the wheel.Turn the wheel until the line turns green then it will say calibration complete.
Interesting that you have made a video about recalibrating your remote after I made comment about how you packed your remote in the bag with the sticks on and the fact that you might need to recalibrate. I had it happen to me with my mini 1 and the only video available was for a Mavic Pro so good to see you make one.
Greetings from the US: I have an unrelated question for you: Do you think it would be possible to charge a Mavic Mini, battery installed, directly from an Anker 21watt solar panel? The panel is designed for charging iPhones off-grid, hence it outputs 5volts. I know that it will be slow. Cheers and thanks for the help. Robert van Vranken, North Peacham Highlands, Vermont.
I saw your other video that mentioned you store your controller in the DJI bag with the sticks attached. Any chance that introduces some calibration issues from time to time? I know the old school RC plane people are SUPER paranoid about the sticks touching things inside their cases, and often have cones/protectors they put on them before storage.
The same thing started happening with my original Mavic Air controller and it was fixed the same way as you fixed yours even though they are completely different controllers.
It's so weird because yesterday I was having the same issue, but I noticed on the phone screen that it said calibration required. Something like that. After I finished it stopped the beeping. Thanks for the video.
I had this problem with my mavic air 1 and didnt solve. I had to open the control remove the sticks open and clean with isopropilic alcool with less then 1 year use. I did it 1 year ago and its fine since this
We have found on new software/firmware on Mini 2 we have lost the ability to reprogram the Fn button. It’s been replaces by C1 C2 and these don’t seem to work.
Laggy video on your smart controller and beeping on the stock controller. Sorry bro! My stock controller was beeping too but this seemed to fix it. Thanks!
So I’m having an issue on a newly purchased Dji mni 2 and my X axis simply won’t register on the right stick. The last few flights I was able to calibrate but did run into the same issue. Now I’ve tried 10 times to no success.
Mine keeps beeping after it tells me calibration was successful, the batteries are all fully charged and it’s driving me crazy. Are there any other fixes for this problem? Help…
I was able to calibrate the sticks, but the wheel doesn't seem to be responding, unfortunately... I guess I might need to get a new controller so I don't have to listen to constant beeping...
You may have turned on the controller while one of the sticks was accidentally being held and not at its centre position. It doesnt like being turned on and detecting movement on the stick so starts beeping.
My classic Mavic Air controller does this almost every time I turn it on..ugh :( It is SO annoying. This is a bug that DJI should fix. I can't believe, so many versions later, it's still an issue.
Mine beeps and I calibrated it, it said successful then started beeping again right of way. I calibrated it many times same thing. BEEPING! Talk about driving a person CRAZY...
Now, if I can figure out how to stop the beeping when my batteries are low, I mean give me about 5 seconds of beeping to let me know, after that, shut the hell up controller!
Just decided to get my drone ready for the weekend and the remote started Wiggin out so I went right to RUclips and searched. You came up right away. It worked for me. No more beeps. Updated firmware. All good for now. Thank you.
You just saved me from annoying tf outta my parents while visiting them. Many thank yous sir 🙏🏾👏🏾🙏🏾👏🏾🙏🏾👏🏾
Thank you kind sir for taking the time to make this video. Absolutely love your content. I have the Mavic Air 2 and hoping to upgrade to Air 2S real soon.
Thanks for watching!
Thanks Henrik, this has been bugging me for a few days now and thanks to you fingers crossed it’s fixed.
.I cannot thank you enough for this video. Your instructions worked on a Phantom 4 ver. 20 The screen prompts in the software do not mention the dial. They only mention the joy sticks so I could not get it to calibrate until after I watched your video. Thank you!
....Problem started in the car.... In my case this problem also starts while I switch on the control while inside the car. But your fix solves the error/beeping. Thanks!
Just upgraded to the Air 2S from my trusty Mavic Air.. it’s an amazing upgrade and even easier to fly.
It really is!
Thank you, this worked for my Mini 2 like a charm!!
Thank you so much it resolved my beeping issue today
Glad it helped
Thank you so much I was sick and tired of that Beeping
Glad I could help
Gladly I haven’t encountered this with my Air 2S but this is good info. Thank you!
Worked in my case too. I have borrowed drone for a few days and that noise was realy worring. Huge thanks!
Thanks for your help, just done my DJI remote beeping.
It can drive you mad :-)
Thank you THANK YOU THANK YOU!!!!!!!!!!!!!!!!!!!!!!!!!!! That beeping was driving me crazy too!
Have the same problem with my mini 2. Hope it works! Thanks bro 🤙🏻
It will
@@TECHDRONEMEDIA It helped! Thanks for your advice.
Hello and thank you so much for your video. One question I have :how will be possible that controller receive the voice when you are spiking during drone is flying?
I really hope this helps. Going to try it this morning!
Thank you for this video, i think i will become crazy when controller starts beeping.
Thank you!! very helpful, I have been noticing the same issue and hopefully it will be solved now.
Yea it works. I don't understand what made it start beeping like that in the first place . Mine started doing that 2 days ago. And I've had it for 4 or 5 months now.
I've never experienced this until just today when I finally updated the firmware. So I'm guessing it's a firmware bug? I actually got it to shut up by switching the flight mode switch back and forth. I then finished all my updates and decided to recalibrate the control anyways, even though the beeping had stopped.
Fixed for my Mini 2 as well
THANK YOU HENRIK.
Thank you so much i get help from this video because i also facing same
Thank you for this video! Very helpful :)
My control never says: callibration successful, I tried for more than 20 minutes, but nothing happened, what can I do??? (I have the firmware up to date)
thx for advice. It works as well on MA2 maybe it is caused by too often using funkction Low R Low L to turn on/off propellers. I had this issue but durring flight it sileced itself. After landing and swaping batteries problem occurs again. Until Your vid, thx.
The beeping was driving me crazy... But I did an update while this thing beeping, powered off and it back on, but it was still making the beeping noise. Saw I note sayi g RC calibration needed... Attempted to do it but then it stop 😳... Without me doing the calibration... BUT just incase... I went in and did the calibration anyways... Thanks for the vid
Used to happen with the air one a lot
Very helpful info thanks.
I just got the air 2s yesterday. when you calibrating remote control and move the sticks you have to move them until the lines turn green at 100% You have to move the sticks in the direction of the arrows until the lines turn green and the same goes for the wheel.Turn the wheel until the line turns green then it will say calibration complete.
Interesting that you have made a video about recalibrating your remote after I made comment about how you packed your remote in the bag with the sticks on and the fact that you might need to recalibrate. I had it happen to me with my mini 1 and the only video available was for a Mavic Pro so good to see you make one.
Also a quick disassembly of the front cover and was able to put a drop of funtac on the speaker to silence it 90%
Sir it really worked thanks that beeping was getting the best of my whew😡
Worked for meeee thank you.
Thanks you it's help's a lot
Thank you for useful information, no annoying sounds any more 👍
Worked....🥳🥳 thanks!!!
Great 👍
You are amazing ❤❤❤❤
Greetings from the US: I have an unrelated question for you: Do you think it would be possible to charge a Mavic Mini, battery installed, directly from an Anker 21watt solar panel? The panel is designed for charging iPhones off-grid, hence it outputs 5volts. I know that it will be slow. Cheers and thanks for the help. Robert van Vranken, North Peacham Highlands, Vermont.
Try it :-)
Thank you!!🙏🏾
Thanks bro
I saw your other video that mentioned you store your controller in the DJI bag with the sticks attached. Any chance that introduces some calibration issues from time to time? I know the old school RC plane people are SUPER paranoid about the sticks touching things inside their cases, and often have cones/protectors they put on them before storage.
Yep I said he might have to recalibrate the remote if he left the sticks on and getting the dreaded beeps is worrying when you get it the first time.
I don’t know why youtube suggested this video to me. Probably the sign I’m looking for to get the DJI Air 2S. LOL And your shirt says “Just do it”. 😩
The same thing started happening with my original Mavic Air controller and it was fixed the same way as you fixed yours even though they are completely different controllers.
It worked for me. Thank you!
It's so weird because yesterday I was having the same issue, but I noticed on the phone screen that it said calibration required. Something like that. After I finished it stopped the beeping. Thanks for the video.
thankyou! my drone wouldnt stop beeping and was driving me up the wall!
I tried several times but it did not stop beeping, any additional cause you might know?
My controller was beeping like this today, i was like what the f.... is going on. It eventually stopped. Now i know, Thank You!
Glad I could help
Think you my friend
Ohh … Takker Henrik 👌✔️👍😎
Har haft denne bip lyd on and off på min nye mavic 3 og jeg var ved at blive sindsyg 😂
Big thanks 😍
It fixed my beeping remote! Thank you :)
I had this problem with my mavic air 1 and didnt solve. I had to open the control remove the sticks open and clean with isopropilic alcool with less then 1 year use. I did it 1 year ago and its fine since this
Fixed the issue! Thank you.
Glad it helped!
Thank you!!!!
We have found on new software/firmware on Mini 2 we have lost the ability to reprogram the Fn button. It’s been replaces by C1 C2 and these don’t seem to work.
My problem is my air2s won't go left or right will this fix it
The green indicator didn’t come up when calibration for my right hand joystick. Pls help
I try to calibrate but its like it doesn't even show i have a left stick.. dont register. Im assuming rc completely broken or unsuable from now on
sound like it
Thanks Henrik!👍
Thank you for this helpful video.
Best regards
ANTJE und LUTZ
Laggy video on your smart controller and beeping on the stock controller. Sorry bro! My stock controller was beeping too but this seemed to fix it. Thanks!
The standard controller was beeping for a while but once I figured out the calibration it was fine
I did the callibration as shown but I dont get a message that it was successull.
Yes mine has been doing the same, pain in the arse…
It worked at the beginning, but the problem came back and it won't stop even with calibration. Any other ideas?
So I’m having an issue on a newly purchased Dji mni 2 and my X axis simply won’t register on the right stick. The last few flights I was able to calibrate but did run into the same issue. Now I’ve tried 10 times to no success.
An update. I have now sent it to DJi for repair, possibly a faulty joystick. I’m not sure if I’ll have to pay for this or if they will replace it.
Mine keeps beeping after it tells me calibration was successful, the batteries are all fully charged and it’s driving me crazy. Are there any other fixes for this problem? Help…
Can you activate the subtitles in your videos?
I was able to calibrate the sticks, but the wheel doesn't seem to be responding, unfortunately... I guess I might need to get a new controller so I don't have to listen to constant beeping...
Sir my (dji mini 2) remote is not working.. Means Its power is not running.. Please help me sir
You may have turned on the controller while one of the sticks was accidentally being held and not at its centre position. It doesnt like being turned on and detecting movement on the stick so starts beeping.
Good information, Hendrik!
Thanks for posting!
👍🏼
Thanks...
My classic Mavic Air controller does this almost every time I turn it on..ugh :( It is SO annoying. This is a bug that DJI should fix. I can't believe, so many versions later, it's still an issue.
My problem is that the right Stick doesn’t work from left to right. It just shows 0% and when the drone is in the air, I canto lector right.
Is the beeping form the OA? Mine keeps beeping even with it off?
Just flick the sticks B4 fireing up the controller... That fixes it
I did the calibration many times but still the same
What cured mine from beeping was to do a RC refresh from Assistant 2.
Thanks♥♥♥♥♥
while calibrating, the gimbal dial does not respond
Mine beeps and I calibrated it, it said successful then started beeping again right of way. I calibrated it many times same thing. BEEPING! Talk about driving a person CRAZY...
ha yes
@@TECHDRONEMEDIA Mine is doing the same same as his, which is still beeping after RC Cal... What gives..?
Mine has 4 light blinking, and won't connect to the aircraft
video starts at 1:10
My air 2s not still calibrating
yesssss thank you it's so embarrassing in front of my gf😄
have you tried recalibrating your girlfriend lololol
All the mavics beep randomly like that, but not with the smart controller
Erik i want to talk with you
I am from taastrup
about?
Now, if I can figure out how to stop the beeping when my batteries are low, I mean give me about 5 seconds of beeping to let me know, after that, shut the hell up controller!
your car' s metal coused the problem, i guess
Doesn’t work
First!
totally useless
worked great!!!!!!!!!!!!!!!
Thank You :)
Thank you !!!