Good circuit with minimum components. The contact probs if working on DC power, the same gathers oxcide on them and lose contact of water. therefore the probs supplying power should supply AC power and the sencers should work on that AC Supply.
Gracias por tu contribución. No obstante, que en la red se encuentran varios ejercicios en los cuales repiten el mismo proceso, acaso no se dan cuenta. Para no ser reiterativo retomo el interrogatorio que se le ha hecho a otra persona que ha publicado lo mismo que tú. "Gracias por un remedio casero tan bueno. Su presentación es muy buena. Quiero agregar una observación a este esfuerzo. Por lo general, el agua se bombea desde el tanque de agua de la planta baja al tanque de agua de la planta superior. El dispositivo que ha explicado funcionará para el tanque de agua de arriba. Sin embargo, debe asegurarse de que haya suficiente nivel de agua en el tanque de agua de abajo. Si esto no está asegurado, la bomba puede funcionar en seco durante mucho tiempo hasta que el tanque de agua subterránea se llene de agua. es una situación peligrosa ya que el motor puede quemarse. Considere agregar otro sensor de nivel de agua para el tanque de agua subterránea. La bomba debe funcionar solo si hay suficiente nivel de agua en el tanque del primer piso. En segundo lugar, Si la electricidad se corta repentinamente cuando la bomba está en funcionamiento, el interruptor de la bomba debe apagarse automáticamente aunque los sensores de nivel de agua den la señal para encender el interruptor de la bomba. De lo contrario, cuando se reanude la energía, la bomba puede volver a encenderse repentinamente. En tercer lugar, debe haber un interruptor de aislamiento para esta unidad de control de nivel automático, que será necesario cuando haya una fuga de agua en el circuito de agua y necesite reparación. Esto provocará que la bomba se encienda / apague hasta que se realice la reparación y es posible que no se note fácilmente "". Debe haber un interruptor de aislamiento para esta unidad de control de nivel automático, que será necesario cuando haya una fuga de agua en el circuito de agua y necesite reparación. Esto provocará que la bomba se encienda / apague hasta que se realice la reparación y es posible que no se note fácilmente "". Debe haber un interruptor de aislamiento para esta unidad de control de nivel automático, que será necesario cuando haya una fuga de agua en el circuito de agua y necesite reparación. Esto provocará que la bomba se encienda / apague hasta que se realice la reparación y es posible que no se note fácilmente "".
instead of giving 220V if i want to use DC 12 V battery so can u tell me which things will be changed like resistors or relay? and i will also will be using a dc water pump ...
must include dry run(sump tank empty protection) ..hint use a npn transistor in series of output of 555 and relay driving transistor with its base connect via 10k to underground sump tank (similer probe as upper tank low high) mark the 3rd sensor war(or interlock). atlernate may depower the 555 with the interlock transistor
Greetings, I am beginner in electro, schematic that you have shared with us, I managed to run it, but if it pleases, to be added again for when the well water has receded, the water pump engine will turn itself off at its sensor limit, even though the sensor to the water tank gives orders are still filling in, thank you.
Hello. I would appreciate a video or diagram for an Automatic Water Level Controller that switches on the pump when water level is full/High (Overflow switch)
@@laamvlogger You mean it's bigger than it should be right? If so, then YES. same problem. If I use Paint program to rescale it, it will lose it's sharpness. It will become pixelated.
This circuit only work if u your tank is on 1st floor. I maded and tested it , the relay automatically goes of and on with 2 pins , number 6 pin get automatically threshold if i connect a long wire with it
Sir lot of thanks for nice job. I have a problem faced with the circuit, when water level touch the Mid sensor then off the relay and when de-touch the mid sensor then relay start again. please help me............. Thanks in advance.
install simple switch in parallel to relay contact s(com and NO) to operate pump manually directly. switch off for auto...pull out power plug for manual force off
Hello Sir your Pcb layout link is not correct... And your circuit is not working... I have build exactly like you but relay start with power even all 3 cable under of water... Please help me out by giving proper guide... thanks
Ahmed Ashiq Chowdhury It was correct, because I uploaded the same exact circuit that was built in my video. Check the Circuit once again using the method I am showing before the final setup. It should work if you built it properly using exact components.
@@LahisTechLT Sir, please you check the diagram on Google drive & your video, check the connection of transistor you will understand also, I use all same components only instead of 2.2k resistance I used 2.7k nothing else... please share your FB link or whatsapp I will show you...
@@a.ashiqchy Yeah Sorry, Neglect the diagram I've attach here, hookup the connections of transistor as in the video (5.00 - 5.04) , I will attach the corrected diagram asap.
@@harshitrajsud9hridn Yeah Sorry, Neglect the diagram I've attach here, hookup the connections of transistor as in the video (5.00 - 5.04) , I will attach the corrected diagram asap. All the connections are correct except the transistor.
.......All the viewers, your kind attention pliz: What if the reservoir tank dries up before the water reaches at the top level to turn off the motor. should you leave the motor run dry for hours and pay a huge bill to motor mechanic to fix it. This idea is totally CRAP, I am an ENGINEER.
10 peace chahie kitne mein haiy 1peace Aur kab tak mil jaenge delivery kahan per Doge aap kahan per aana hoga mere ko Ek peace ka price kya hai apna contact number send karo please apna contea no sead ko bro OK g... N..
बहुत-बहुत शुक्रिया जनाब आपने सरलता से समझाया बहुत अच्छा लगा ।
greeting from bangladesh... I was looking for the pcb layout and suddenly got this. thanks for the good work
Hello and thanks for your interesting video. Can this indicator be used for a tank that is approximately 9m away from the water pump?
Good circuit with minimum components. The contact probs if working on DC power, the same gathers oxcide on them and lose contact of water. therefore the probs supplying power should supply AC power and the sencers should work on that AC Supply.
May i can use this circuit in direct water pump motor in my home ??
Upto what range of water tanks it can be used...???
How add dry protection pump sir in ur circuit,pliss help me
Good job😊 sir haw can i gat lt pcb
Very beautiful project sir
Great job 👍🏻
Super video sri
Gracias por tu contribución. No obstante, que en la red se encuentran varios ejercicios en los cuales repiten el mismo proceso, acaso no se dan cuenta. Para no ser reiterativo retomo el interrogatorio que se le ha hecho a otra persona que ha publicado lo mismo que tú. "Gracias por un remedio casero tan bueno. Su presentación es muy buena. Quiero agregar una observación a este esfuerzo. Por lo general, el agua se bombea desde el tanque de agua de la planta baja al tanque de agua de la planta superior. El dispositivo que ha explicado funcionará para el tanque de agua de arriba. Sin embargo, debe asegurarse de que haya suficiente nivel de agua en el tanque de agua de abajo. Si esto no está asegurado, la bomba puede funcionar en seco durante mucho tiempo hasta que el tanque de agua subterránea se llene de agua. es una situación peligrosa ya que el motor puede quemarse. Considere agregar otro sensor de nivel de agua para el tanque de agua subterránea. La bomba debe funcionar solo si hay suficiente nivel de agua en el tanque del primer piso. En segundo lugar, Si la electricidad se corta repentinamente cuando la bomba está en funcionamiento, el interruptor de la bomba debe apagarse automáticamente aunque los sensores de nivel de agua den la señal para encender el interruptor de la bomba. De lo contrario, cuando se reanude la energía, la bomba puede volver a encenderse repentinamente. En tercer lugar, debe haber un interruptor de aislamiento para esta unidad de control de nivel automático, que será necesario cuando haya una fuga de agua en el circuito de agua y necesite reparación. Esto provocará que la bomba se encienda / apague hasta que se realice la reparación y es posible que no se note fácilmente "". Debe haber un interruptor de aislamiento para esta unidad de control de nivel automático, que será necesario cuando haya una fuga de agua en el circuito de agua y necesite reparación. Esto provocará que la bomba se encienda / apague hasta que se realice la reparación y es posible que no se note fácilmente "". Debe haber un interruptor de aislamiento para esta unidad de control de nivel automático, que será necesario cuando haya una fuga de agua en el circuito de agua y necesite reparación. Esto provocará que la bomba se encienda / apague hasta que se realice la reparación y es posible que no se note fácilmente "".
instead of giving 220V if i want to use DC 12 V battery so can u tell me which things will be changed like resistors or relay? and i will also will be using a dc water pump ...
excelente video , para poder usar el circuito con 5v que valores de resistencias tendria que usar?
Can you supply pcb with assembled components
must include dry run(sump tank empty protection)
..hint use a npn transistor in series of output of 555 and relay driving transistor with its base connect via 10k to underground sump tank (similer probe as upper tank low high) mark the 3rd sensor war(or interlock). atlernate may depower the 555 with the interlock transistor
Greetings, I am beginner in electro, schematic that you have shared with us, I managed to run it, but if it pleases, to be added again for when the well water has receded, the water pump engine will turn itself off at its sensor limit, even though the sensor to the water tank gives orders are still filling in, thank you.
Yes it's work. Please make this type another project
Nice demonstration. My water tank is in 5th floor. Will this work?
Yes, definitely
will you sell this with sensors ? 10 minut dry rung possible to protect motor ?
Hi sir tell me how many hp can work on this and up to how many feet tools its work
Hello. I would appreciate a video or diagram for an Automatic Water Level Controller that switches on the pump when water level is full/High (Overflow switch)
Do I need to replace the 12v relay to 5v? because I have a 3-5v mini pump
Help me bro
can it works on three phase motor ?
Hi ❤
ican use wair vari toll 40 meter
After download the pcb in PDF format, do I have to rescale it to correct size?
Hello bro, after downloading the PDF file, I make the circuit of the pins larger than the components, are you like me?
@@laamvlogger You mean it's bigger than it should be right?
If so, then YES. same problem.
If I use Paint program to rescale it, it will lose it's sharpness. It will become pixelated.
From Bangladesh 🇧🇩
brother can I use 9v battery for this circuit on 24v relay (spdt)? Pls reply
Can we use battery instead of dc connector
will it work for 90 watts water pump?
How much Cast it's 10th pics
At the 30 feet hight this circuit not working .motor is not cut off.tell me why transformer 12v 500m amp.at this circuit
Working Perfectly (Y)
It works?
Pcb manufacturing at reasonable price
contect no :- 7065661837
This circuit only work if u your tank is on 1st floor.
I maded and tested it , the relay automatically goes of and on with 2 pins , number 6 pin get automatically threshold if i connect a long wire with it
Can anyone tell me how much amperage of 12v DC current can I push into it?
If it is salty water,what type of sensor to be. Used?
etsy (solar well controller kit)
Sir lot of thanks for nice job.
I have a problem faced with the circuit, when water level touch the Mid sensor then off the relay and when de-touch the mid sensor then relay start again. please help me.............
Thanks in advance.
Same encounter
What is the range
Is the circuit connection correct?
Can i use bc548 in the place of 547
//Varun // can't
Can u please explain how to add auto manual switch in this circuit
install simple switch in parallel to relay contact s(com and NO) to operate pump manually directly. switch off for auto...pull out power plug for manual force off
Thank you
Can you give block diagram of this structure
please add dry run protection if water not rech in tank in 1 minute motor should stop
Will it work for 2 kw motor?
230v any motor! Since the Relay is 230v!
use contactor(the pcb relay as pilot duty to connect to coil of other higher ampere relay contactor (atleast 15-20A contacts for 2kw)
Sir agar tank full ho aur mujhe pump 1min chalani ho to kya kari kaha se connection karu kis components k thru
connect a timer switch
Thank you brother super
Same question
Pcb design link not working. Please help
You are right..Bro..
Hai sir cost of the PCB and components thanks
Please explain Pump CONETION
No explanation of Circuit ????
What abt second tank control
etsy (solar well controller kit)
Price ??
Pcb siz?
Bro iska pcb layout dedi
where is schematic diagram of circuit ?
Hello Sir your Pcb layout link is not correct...
And your circuit is not working... I have build exactly like you but relay start with power even all 3 cable under of water...
Please help me out by giving proper guide... thanks
Ahmed Ashiq Chowdhury It was correct, because I uploaded the same exact circuit that was built in my video. Check the Circuit once again using the method I am showing before the final setup. It should work if you built it properly using exact components.
@@LahisTechLT Sir, please you check the diagram on Google drive & your video, check the connection of transistor you will understand also, I use all same components only instead of 2.2k resistance I used 2.7k nothing else... please share your FB link or whatsapp I will show you...
I also tried this circuit it not working I have same problem
@@a.ashiqchy Yeah Sorry, Neglect the diagram I've attach here, hookup the connections of transistor as in the video (5.00 - 5.04) , I will attach the corrected diagram asap.
@@harshitrajsud9hridn Yeah Sorry, Neglect the diagram I've attach here, hookup the connections of transistor as in the video (5.00 - 5.04) , I will attach the corrected diagram asap. All the connections are correct except the transistor.
Rate
thanks bro
Hello Sir ye circuit chahie
Pls give circuit diagram
sir,can i get the PCB from you??
Link is in the description
etsy (solar well controller kit)
etsy (solar well controller kit)
How to get pcb layout first
it's in the video description
Pcb rate caplit
sir pz circuit digram btayie iska ki
Explanation plz
Who notice the switch sound😏😏
भाई पेपर पर कोपर लाईन केसो बनती है पेपर नाम बोलो
pleas gev me this circuit.
etsy (solar well controller kit)
Skematic please
Pcb milga
Bro send me circuit to build in PCB
etsy (solar well controller kit)
I need 10 nos
আসসালামু আলাইকুম ভাই আপনি কন্টাক নাম্বার চাই
Mixing background music in such tutorial videos is very very very bad manners. 👎👎👎👎👎👎
Send me your pcb
10
Pesh k
Ye pcb mujhe leni ha 100
Kaha se miljayengi
9045001414 W
.......All the viewers, your kind attention pliz: What if the reservoir tank dries up before the water reaches at the top level to turn off the motor. should you leave the motor run dry for hours and pay a huge bill to motor mechanic to fix it. This idea is totally CRAP, I am an ENGINEER.
m also searching for that will you provide the working circuit ? i tried many but didnot work properly.
10 peace chahie kitne mein haiy 1peace
Aur kab tak mil jaenge delivery kahan per Doge aap kahan per aana hoga mere ko Ek peace ka price kya hai apna contact number send karo please apna contea no sead ko bro OK g... N..
Sir please give the circuit diagram