Disculpa una pregunta ya no me funciona la tolva del tóner y se fue al código 20, como le hago para cargar manual la unidad de revelado? Tendrás algún video de como sacar la unidad de revelado?
Code: E061-0101 Potential control error (VD) Potential in the dark area did not fall within the range (target value +/-10V) although retry was executed 8 times at VD potential control. 1. Check the connection of the Pre-exposure LED (connector connection, open circuit, the caught cable). 2. If the current value of the Primary Charging Roller (COPIER > DISPLAY > DPOT > PRIM-C) is 1550 micro A or higher, execute 2-1 to 3. 2-1. Increase the grid voltage of the Primary Charging Assembly by 100V (COPIER > ADJUST > HV-PRI > PRI-GRID). 2-2. Execute the potential control (COPIER > FUNCTION > DPC > DPC). 2-3. Turn OFF and then ON the power. 3. Check the installation of the Primary Charging Assembly (connector connection, open circuit, the caught cable). 4. Check the installation of the Primary Charging High Voltage PCB (PCB11), and its connection (connector connection, open circuit, the caught cable). 5. Check the installation of the Drum Motor (M1), and its connection (connector connection, open circuit, the caught cable). 6. Replace the parts. • Primary Charging Assembly • Primary Charging High Voltage PCB • Drum Motor (M1) • Main Driver PCB (PCB2) • DC Controller PCB (PCB1)
Salam walakum bhai toshiba 243 machine my 2 tipe ka symble show karra ak to tray may teer ka symble dusra doot doot ka symble isko reset kaysay karna aap batsak tay hai kia
1. Connector disconnection/open circuit of the Scanner Unit (DADF). 2. Connector disconnection/open circuit of the Reader Controller PCB (PCB1). 3. Failure of the Scanner Unit (DADF). 4. Failure of the Reader Controller PCB (PCB1).
Description: Error in the Feed Roller Disengage/Buffer Flapper Motor (Finisher-D1). The Feed Roller Separation HP Sensor does not detect the disengage roller when the Feed Roller Disengage/Buffer Flapper Motor has been driven for 3 seconds.
Harness between the DC Controller PCB and the Secondary Transfer High-Voltage PCB Perform the following in the order while checking whether the error is cleared. 1. Check the Harness (on the DC Controller side and the Secondary Transfer High-Voltage PCB side). If it is not fully connected or obliquely connected, check the operation of the main machine by disconnecting it then connecting it again. 2. If no error is seen in the Harness in Procedure 1 or if an error is not cleared by disconnecting it and then connecting it again, replace the Secondary Transfer High-Voltage PCB and check the operation of the main machine. 3. If an error is not cleared in Procedure 2, replace the DC Controller PCB and check the operation of the main machine. Before replacing the DC Controller PCB, back up the service mode data and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
First clean the document glass scanner and charging corona unit then set up the following service program. *(COPIER (LEVEL2)> DISPLAY> DPOT> PRIM-C)* - *Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES.*
Open the primary charging shutter, the machine will run without it. Primary Charging Shutter HP open error. The Primary Charging Shutter Sensor (PS94) detects that the shutter is opened although it is moved to the close position.
sir, I want to ask .. my printer adv 6075 often comes out code e000061-0101. technician is already there but the error still came out .. how to fix it .. can you help me
1. Check the connection of the Pre-exposure LED (connector connection, open circuit, the caught cable). 2. If the current value of the Primary Charging Roller (COPIER > DISPLAY > DPOT > PRIM-C) is 1550 micro A or higher, execute 2-1 to 3. 2-1. Increase the grid voltage of the Primary Charging Assembly by 100V (COPIER > ADJUST > HV-PRI > PRI-GRID). 2-2. Execute the potential control (COPIER > FUNCTION > DPC > DPC). 2-3. Turn OFF and then ON the power. 3. Check the installation of the Primary Charging Assembly (connector connection, open circuit, the caught cable). 4. Check the installation of the Primary Charging High Voltage PCB (PCB11), and its connection (connector connection, open circuit, the caught cable). 5. Check the installation of the Drum Motor (M1), and its connection (connector connection, open circuit, the caught cable). 6. Replace the parts. • Primary Charging Assembly • Primary Charging High Voltage PCB • Drum Motor (M1) • Main Driver PCB (PCB2) • DC Controller PCB (PCB1)
Thank you sir
Saludos has reparado una copiadora en nicaragua américa Central gracias....
¿Cómo entendiste? Escriba los detalles, gracias.
👍👍👍👍👍🇮🇩🇮🇩🇮🇩🇮🇩
Sir can you help for canon ir 6255 as getting empty tonner sign , but the tonner bottle is full .
The toner bottle is not genuine or the toner hopper's lock is broken
👍👍❤️❤️❤️❤️
Disculpa una pregunta ya no me funciona la tolva del tóner y se fue al código 20, como le hago para cargar manual la unidad de revelado? Tendrás algún video de como sacar la unidad de revelado?
ruclips.net/video/o74cg4eG_So/видео.html
Morning. Can you make a video on the hard drive replacement for the e7-03 error. Thanks
The model was not written.
👌
Code: E061-0101
Potential control error (VD)
Potential in the dark area did not fall within the range (target value +/-10V) although retry was executed 8 times at VD potential control.
1. Check the connection of the Pre-exposure LED (connector connection, open circuit, the caught cable).
2. If the current value of the Primary Charging Roller (COPIER > DISPLAY > DPOT > PRIM-C) is 1550 micro A or higher, execute 2-1 to 3. 2-1. Increase the grid voltage of the Primary Charging Assembly by 100V (COPIER > ADJUST > HV-PRI > PRI-GRID). 2-2. Execute the potential control (COPIER > FUNCTION > DPC > DPC). 2-3. Turn OFF and then ON the power.
3. Check the installation of the Primary Charging Assembly (connector connection, open circuit, the caught cable).
4. Check the installation of the Primary Charging High Voltage PCB (PCB11), and its connection (connector connection, open circuit, the caught cable).
5. Check the installation of the Drum Motor (M1), and its connection (connector connection, open circuit, the caught cable). 6. Replace the parts. • Primary Charging Assembly • Primary Charging High Voltage PCB • Drum Motor (M1) • Main Driver PCB (PCB2) • DC Controller PCB (PCB1)
Salam walakum bhai toshiba 243 machine my 2 tipe ka symble show karra ak to tray may teer ka symble dusra doot doot ka symble isko reset kaysay karna aap batsak tay hai kia
Display ka photos begia whatsapp +8801312616163
Canon IR Advance 6275, E 280 - 0101 video sir please send. Tanks.
1. Connector disconnection/open circuit of the Scanner Unit (DADF). 2. Connector disconnection/open circuit of the Reader Controller PCB (PCB1). 3. Failure of the Scanner Unit (DADF). 4. Failure of the Reader Controller PCB (PCB1).
Sir i try this but still same error any another issue tell me plz
Sir can you help for about Canon ir C5535i paper size error occured tray 2 cannot detect paper..thank
ruclips.net/video/N1G_-ppG1-Y/видео.html
E 568-8002 canon ir8250
Description:
Error in the Feed Roller Disengage/Buffer Flapper Motor (Finisher-D1). The Feed Roller Separation HP Sensor does not detect the disengage roller when the Feed Roller Disengage/Buffer Flapper Motor has been driven for 3 seconds.
@@TechHumayunkabir I want the picture exactly
@@สุรพงษ์บุญคง ruclips.net/video/7OdC4sCezek/видео.html
ruclips.net/video/7OdC4sCezek/видео.html
Canon 6275 problem machine on direct energy saver mode
I am thinking about the problem of power supply board
Canon 6275 Pawar problem video sir please sender
,
sir photo copy ok but printout not clear in adv 8205 pls sand me solution
Adjust scanner mirror
ir advance 6075 primary charging air supply fan error solution
I think fan jam or connected problem
Ir advance 6075 8105 error 808 007 , how to solve
Please share
error code 004 ir advance 8105 please what to fix
ruclips.net/video/SOSUKm0U4FE/видео.html
Same as
please ; err E00064-1401 immage runner DX c5740
Harness between the DC Controller PCB and the Secondary Transfer High-Voltage PCB
Perform the following in the order while checking whether the error is cleared.
1. Check the Harness (on the DC Controller side and the Secondary Transfer High-Voltage PCB side). If it is not fully connected or obliquely connected, check the operation of the main machine by disconnecting it then connecting it again.
2. If no error is seen in the Harness in Procedure 1 or if an error is not cleared by disconnecting it and then connecting it again, replace the Secondary Transfer High-Voltage PCB and check the operation of the main machine.
3. If an error is not cleared in Procedure 2, replace the DC Controller PCB and check the operation of the main machine. Before replacing the DC Controller PCB, back up the service mode data and restore the backup data after the replacement so the data may be able to be protected.
- Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP
- Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
How to do service mode and reset error cod c 01solution toshiba estudio 18
,
Hlo bhai
Error code E000060-0002
Issue found
Not clearing error
When power on error comes
What problem does it
Detach the black colored charging shutter from the lever.
Bhai
I had replaced charger unit primary
Although same problem
Sir please help to resolve Error E000061 0101 on canon 6255
First clean the document glass scanner and charging corona unit then set up the following service program.
*(COPIER (LEVEL2)> DISPLAY> DPOT> PRIM-C)*
- *Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES.*
I have the problem with sharp mx it gives error u2_30. Please, can anyone help me
ruclips.net/video/1Ml3SjcTW_w/видео.html
CONTUNUE ERROR E00060-0001
Open the primary charging shutter, the machine will run without it.
Primary Charging Shutter HP open error. The Primary Charging Shutter Sensor (PS94) detects that the shutter is opened although it is moved to the close position.
sir, I want to ask .. my printer adv 6075 often comes out code e000061-0101. technician is already there but the error still came out .. how to fix it .. can you help me
1. Check the connection of the Pre-exposure LED (connector connection, open circuit, the caught cable). 2. If the current value of the Primary Charging Roller (COPIER > DISPLAY > DPOT > PRIM-C) is 1550 micro A or higher, execute 2-1 to 3. 2-1. Increase the grid voltage of the Primary Charging Assembly by 100V (COPIER > ADJUST > HV-PRI > PRI-GRID). 2-2. Execute the potential control (COPIER > FUNCTION > DPC > DPC). 2-3. Turn OFF and then ON the power. 3. Check the installation of the Primary Charging Assembly (connector connection, open circuit, the caught cable). 4. Check the installation of the Primary Charging High Voltage PCB (PCB11), and its connection (connector connection, open circuit, the caught cable). 5. Check the installation of the Drum Motor (M1), and its connection (connector connection, open circuit, the caught cable). 6. Replace the parts. • Primary Charging Assembly • Primary Charging High Voltage PCB • Drum Motor (M1) • Main Driver PCB (PCB2) • DC Controller PCB (PCB1)