Перед тем как включить тестер в первый раз он его тряс 5 минут, затем для следующего включения ещё раз тряс. Катушка с магнитами в этом исполнении с очень низким КПД. Если нужно работать весь день с тестером в режиме прозвонки думаю у вас руки отвалятся прежде чем закончите работу.
I don't see the point of the 1st one apart from showing the working principle of a shunt resistor. Your meter has Amp mode. 2nd one, saw you do this on another video. One led would have done. The cob uses to much power. 3rd one.. ...... I won't comment..... 4th one, love it. I need to do this with a few of my meters.👍 And the 5th one, these are the type one meter hacks i love to see. PLEASE MAKE A VIDEO WITH MORE INTERESTING LITTLE HACKS LIKE THAT. 👍🇮🇪🙏
I think the point of the first one is that the meter’s built-in amp mode only goes up to 10 amps. With the setup here, though, you could measure a higher current. Sorta.
@@tehlasermy yellow multi meter mili micro ampere and 10 amp reading automatically increase 0.45 1.00 ... so on. (without touching probes ) So what is fault in any idea?
At high currents, the wire expands and causes the measured current to be measured higher than it actually is. This is suitable for currents up to 1 ampere. I also use this method sometimes. I have also been using the Lithium battery, MT3608 and on-off button method in all my multimeters for years. If you do not have an MT3608, you can connect two lithium batteries in series. I definitely recommend it. Especially if you are making long-term experimental measurements like me.
Müzik ve işaret yerine yine eskisi gibi konuşsanız daha güzel oluyor ama, sanırım o zaman yurt dışı izlenme sayısının azalacağını düşünüyorsunuz. Müzikler berbat siz mükemmelsiniz. Sanırım telif hakkı etkili müziklerde de. Bu müziklerle yurt dışı arkadaşları kopyalıyor gibi oluyor ama siz daha iyisiniz. Kendi konseptinizi oluşturmanızı tavsiye ederim. Ayrıca canlı yayınların devamını istiyoruz. Kolay gelsiz Zafer Bey.
💡 Breathalyzer looks good when embedded in this kind of multimeters to disallow any measurements if your alcohol exceeds 0.16 mg/l 🥴. It will prevent multemeter from being burnt down when, for instance, pluged into the mains while resistance measuring have been chosen. CAUTION: a few (or maybe all) multimiter producing companies may go bankrupt after such improvement.
@@ZAFERYILDIZ52 hangisi daha uygun olur onu bilmiyorum devrede 2 tane tip 35c var 10A kadar çıkış verebiliyor 0-30v ayarlı. bazı korumalar sabit çıkışlar için. hangisi benim devreme uygun olur?
@@ZAFERYILDIZ52all your videos are very good but I don't understand because I have to lose a broken multimeter with jumping numbers I want to do a project but don't know how to start
Блин по 3 пункту. Идея.. А то всегда когда нужно батарея разряжена. А нужно на 2 - 3 минуты произвести замер. Или на вахте - вечно разряженная крона, и купить негде.
Hey bro can you tell me you can uses projects for wire name, actually I'm not understanding my nearest electronics shopkeeper What is the name of this wire?
Первый сюжет показался - херня. Для настройки токоизмерительного шунта нужен лабораторный БП с регулировкой тока. А вот последний - реально годный. Пошёл на Алике искать MH-sensor.
50watts from a single 3.7v battery is a bit insane! It won't last long enough. Also if you want 50watt at 3A you will need 17volts that's almost 5 times the voltage so you will need five times the current input or 15A from a 3.7v cell. THAT my friend is doubly insane! Please learn some basic design skills before asking someone to do all the work for you! 🤔🤔🙄
Hello, perfect multimeters upgrades. But i've got one question. Would it be possible to have a circuit that can measure higher alternating current using a toroid current transformer and multimeter? I would love to see a circuit like this 🙂 thanks for it 😊👍
ну чо сказать подсветка вещ полезная(хотя жрет многа) а вот шунт ис куска меди это отстой точности никакой... трясучка на ионисторе это для тех кто поигратся хочет тут либо мерить либо трясти переделка на литий самая востребованаяи полезная доработка уже давно переделал все на литик
No battery hack is bloody fantastic. Well done.
После обгрейда мультик даже погоду на Марсе показывает !!!
А как же энергосбережение🤔крона и так дорого и не долго😟🇷🇺🇷🇺🇷🇺🇷🇺🇷🇺🇷🇺
Есть мультиметры с питанием от 3 вольт, а ввопще Китай все за нас придумал и на Али есть кроны с зарядкой по usb
Thank you very much I'm still learning
7:02 Bu parça için LCD ekrandan sökmek şart mıdır ? Işık geçirgenliği olan bir parça kağıt kullansak olmaz mı ?
For increasing current , shoul be winding opposite coil into 2 parts each other !
The battery-less meter is great ... how long will it last, before you need to shake to charge the cap?
Перед тем как включить тестер в первый раз он его тряс 5 минут, затем для следующего включения ещё раз тряс. Катушка с магнитами в этом исполнении с очень низким КПД. Если нужно работать весь день с тестером в режиме прозвонки думаю у вас руки отвалятся прежде чем закончите работу.
I don't see the point of the 1st one apart from showing the working principle of a shunt resistor. Your meter has Amp mode.
2nd one, saw you do this on another video. One led would have done. The cob uses to much power.
3rd one.. ...... I won't comment.....
4th one, love it. I need to do this with a few of my meters.👍
And the 5th one, these are the type one meter hacks i love to see. PLEASE MAKE A VIDEO WITH MORE INTERESTING LITTLE HACKS LIKE THAT. 👍🇮🇪🙏
I think the point of the first one is that the meter’s built-in amp mode only goes up to 10 amps. With the setup here, though, you could measure a higher current. Sorta.
@@tehlasermy yellow multi meter mili micro ampere and 10 amp reading automatically increase 0.45 1.00 ... so on. (without touching probes )
So what is fault in any idea?
At high currents, the wire expands and causes the measured current to be measured higher than it actually is. This is suitable for currents up to 1 ampere. I also use this method sometimes. I have also been using the Lithium battery, MT3608 and on-off button method in all my multimeters for years. If you do not have an MT3608, you can connect two lithium batteries in series. I definitely recommend it. Especially if you are making long-term experimental measurements like me.
Огромное спасибо уважениемый -отличная подсказка сделаю на своем приборе обязательно,👍
hocam yine harika bir video, videoları bölümlendirseniz daha rahat izleyebiliriz diye düşünüyorum
3 способ отборная дичь и работает только благодаря склейкам видео (не ну видели???, он трясет без нагрузки, а у него +0.001V😂)
Müzik ve işaret yerine yine eskisi gibi konuşsanız daha güzel oluyor ama, sanırım o zaman yurt dışı izlenme sayısının azalacağını düşünüyorsunuz. Müzikler berbat siz mükemmelsiniz. Sanırım telif hakkı etkili müziklerde de. Bu müziklerle yurt dışı arkadaşları kopyalıyor gibi oluyor ama siz daha iyisiniz. Kendi konseptinizi oluşturmanızı tavsiye ederim. Ayrıca canlı yayınların devamını istiyoruz. Kolay gelsiz Zafer Bey.
💡 Breathalyzer looks good when embedded in this kind of multimeters to disallow any measurements if your alcohol exceeds 0.16 mg/l 🥴. It will prevent multemeter from being burnt down when, for instance, pluged into the mains while resistance measuring have been chosen. CAUTION: a few (or maybe all) multimiter producing companies may go bankrupt after such improvement.
Very nice.
Wow, the backlight for the meter is additional a lamp for night.. 🙂
Hello Thanks 🎉
начал обновлять мультиметр......получился электроминетчик.Спасибо за видео
Wonderful creation man . liked and keep it up from bharat.
Thanks Zafer....I'am your follower....do you know Arabic
I'm just waiting for your 1M...🎉🎉
После всех этих апгрейдов мультик обрёл разум и ушол из дома😮
Did you notice little battery icon when backlight is attached (#2)? LED is draining power so device can give you wrong measurements
Nice!
У меня таких мультиков давно нет, только проф и полу проф.
hocam ayarlanabilir güç kaynağına kanalınızdaki kısa devre korumalarından hangisi daha iyi olur röle ile olanlar sanırm işe yaramaz (0-30v)
Seçim sana kalmış kardeşim istedigini ekleyebilirsiniz
@@ZAFERYILDIZ52 hangisi daha uygun olur onu bilmiyorum devrede 2 tane tip 35c var 10A kadar çıkış verebiliyor 0-30v ayarlı. bazı korumalar sabit çıkışlar için. hangisi benim devreme uygun olur?
@@ZAFERYILDIZ52all your videos are very good but I don't understand because I have to lose a broken multimeter with jumping numbers I want to do a project but don't know how to start
Beautiful mind
Вопрос такой у меня есть bldc двигатель n5065 kv 270 подскажите какой нужен для него контролер😊
Блин по 3 пункту. Идея.. А то всегда когда нужно батарея разряжена. А нужно на 2 - 3 минуты произвести замер. Или на вахте - вечно разряженная крона, и купить негде.
Думаю он заранее зарядил конденсатор, такой конструкцией не выйдет получить достаточно энергии
Zafer Ustam Bu Ucuz Sarı Multimetrelerin İçinden Hangi Markayı Tavsiye Edersiniz Multimetrem Var Ama Ekstradan Şarjlı Yapmak İstiyorum 😕
Hepsinin özellikleri aynı marka farketmez bir yanlış ölçümde çöp oluyorlar
@@cevdetylmaz7553 Aynen Ustam Doğru Tespit 😕🙂
Hey bro can you tell me you can uses projects for wire name, actually I'm not understanding my nearest electronics shopkeeper What is the name of this wire?
Первый сюжет показался - херня. Для настройки токоизмерительного шунта нужен лабораторный БП с регулировкой тока. А вот последний - реально годный. Пошёл на Алике искать MH-sensor.
Abi selamin aleykum invertor yapmak istiyorum bunu bilgisayar guc kaynagi ile yapabilirmiyim sana zahmet yardimci olurmusun
Sir please make a voltage booster 50 watt and 3 ampere which oprate 3.7v battery
50watts from a single 3.7v battery is a bit insane! It won't last long enough. Also if you want 50watt at 3A you will need 17volts that's almost 5 times the voltage so you will need five times the current input or 15A from a 3.7v cell. THAT my friend is doubly insane! Please learn some basic design skills before asking someone to do all the work for you! 🤔🤔🙄
Hello, perfect multimeters upgrades. But i've got one question. Would it be possible to have a circuit that can measure higher alternating current using a toroid current transformer and multimeter? I would love to see a circuit like this 🙂 thanks for it 😊👍
Disculpen pero quien repara un artefacto sin luz
Votre musique true note timpant
👍❤️❤👋👋
👍👍👍
That device had origin DC ampe metter 😅 we dont need to upgrade like this
Для контента сойдёт, а в жизни не пригодится, по причине нерентабельности !
🇷🇺🤝🇹🇷
süper
dont want to be mean but iints spelled shunt resistor
🎉🎉🎉🎉🎉
ну чо сказать подсветка вещ полезная(хотя жрет многа) а вот шунт ис куска меди это отстой точности никакой... трясучка на ионисторе это для тех кто поигратся хочет тут либо мерить либо трясти переделка на литий самая востребованаяи полезная доработка уже давно переделал все на литик
😘😘😘
WTF?
👎👎👎👎👎👎👎👎👎
NO TIENES ALMA DE PROFESOR O MAESTRO.... TODO ES COMPLICADO...
Para un ser inferior, todo le es complicado.
3rd...hilarious...so funny...