I can't tell if you're being snarky or comical, but yes. The cats kill themselves, then the motor strangles to death soon after. Best to just remove the cats before your floorboards melt.
not sure if you guys cares but if you guys are bored like me atm then you can watch all the new movies and series on Instaflixxer. Been streaming with my girlfriend recently :)
nice i got one on mine a lot of people tell me i need two pipes but ive drove mine for 7 years and she still braaaaps 04 150,000 + miles also make sure you keep gas in it. mine stayed on empty constantly and i had to put a fuel pump in
I just got a rx8 about a month ago and I’m hoping to get it all fixed up and get this exhaust got it as a project for 1600 and it’s bone stock needs a lot of work but has potential
Did you have to modify the hangers for the hks exhaust to fit the s2? I’ve heard people say they cut the exhaust shroud because the exit pipe touches it.
I would check it doesnt run lean sean after putting that exhaust on. I put the toyo sport manifold, decat pipe (no resonator) and back box on a series 1 and it ran lean. Needed a remap or stand alone chip maybe would have done it. Your S1 will run if its got more than 5 bar compression at whatever turn over speed you got. If you put the 2 kw 14 tooth pinion starter on plus an upreted battery e.g 680 CCA it will spin over at 350 to 400 rpm and move up the compression curve to get it started.
David rx8 Thanks for the advice! The s2 seems to run weird since the exhaust install and my gas mileage is terrible lol. The s1 has a new remanufactured engine but the starter clicks and wont turn the engine over. It tested good but i think the starter isnt getting enough power or something? I need to look into it soon. But yeah i plan on getting the s2 tuned to get rid of the cel and get the car running smooth again!
Hi sean, if you put a 200ohm resistor (which will cost next to nothing) in line to the coolant temp sensor it will fool the ecu into thinking the engine is cooler than it is and the map settings will be there fore be richer on fuel and idle speed will be about 1000 rpm. Its a cheap way to remap it. But the fan wont cut in until later so if its hot or you are in traffic watch out for this. You can overcome it by turning the a/c on which causes the fans to run or put an aftermarket fan temp kit on which consists of a temp sensor in the top hose with an adjuster unit. Without a Cobb access port its one way to change the map settings. I put the exhaust on my S1 and it lost the power it gained if that makes sense due to running lean - plugs were white. I can give you the wire colours and where to splice in if you want to try it. I am in UK and have had loads of rx8s. over here we have an s1, the s2 is not like yours it is an s1 with no plastic on the seat backs and different ecu software. I also have an R3 which looks like your s2 but with a body kit with rear spoiler, 19" wheels other mods such as extra oil injector on apex seals, recaro seats etc over here the rx8s are cheap to buy as what we call the road tax is £600 per year (maybe $750) and fuel is £1.40 per litre so they are expensive to run. But the rx7s are expensive and a silver one like yours about £10,000 minimum without the engine. @@seanhaight3939
@@seanhaight3939 forgot to say check the engine earth and clean it up on the S1. It is the main earth for the starter and located below the spark plugs just above the sump pan join. It bolts to a bracket that also unbolts from the engine so 2 connections to go bad.
David rx8 Yeah man ill try that later this week and see if it fixes the starting process on the s1. As for the s2 there is an ecu reflash that i can get for $180 that turns the fans on sooner, gets rid of the cel, raises the rpm to 950, and says itll get better mpg also. Seems like a good deal!
Sean Haight SWEET! I CANT WAIT TO SEE THEM! by any chance could you tell me the exact exhaust kit this is or a link to where I could purchase it? I love the way it sounds thanksss
If you keep your stock midpipe you wont need to change anything but if you buy an aftermarket midpipe then they have a screw in location for the O2 sensor but because there isnt a cat on the aftermarket pipe, it will throw a check engine light. Its way better for rotary engines to not have a cat so definitely delete it if your state doesnt make you have one. I have a video on rx8 midpipes so itll show you everything.
Yeah i put on a full hks exhaust with a cat delete and a resonator delete and it opened the car up alot. In the next video i installed a different midpipe that was catless and had a resonator. If you dont have a resonator the car is super raspy over 4k rpm. I recommend them for sure! I describe all the benefits and differences in that video. Sounds way better!
The kit is a catback and it doesnt come with a resonator. If you buy the other single exit hks exhaust for the rx8, it comes with a resonator. The tips and muffler position are different for both kits. In this video i installed a catless and resonatorless pipe but the next video i uploaded has an aftermarket catless pipe with a resonator on it. It sounds much better with a resonator lol
Ok. I was just trying to make sure before I purchase the hks hi power that it runs from the cat back. I thought it ran from the headers back deleting the cat.
@@josephbassil4171 I looked online and never saw a kit that has it. The hks kit isnt too expensive for such a good quality exhaust so with the cat delete pipe, the entire exhaust may cost around $750. Not too bad!
Im not sure? Most cars in American only have an oil pressure gauge. My genesis coupe has an oil temp gauge and it's super helpful. I wish my Rx8 had one because hot oil in a rotary is bad news! 😵 Im going to look into it and see if a European Rx8 dash cluster would work on an American Rx8!
@@neoney after these 3 years i actually owned one: there's just a indicative oil temp gauge. I installed a riser between the block and the fileter, and added aftermarket oil temp and pressure gauges
Oscar Amador Yeah you have to turn the key into to the on position, without starting it, and push the gas pedal to full throttle until you hear a noise. The noise means the fuel is cutoff so it wont send anymore fuel. So with your foot on full throttle, turn the key to start the car and it will turn the engine over and it will pump out the gas from inside the engine. Do that for like 15-20 seconds and then take your foot off the gas and start the car like normal
Oscar Amador You can change it through the same settings as how you change the time. Scroll through the options and itll let you change the display title
Dominic Blais I havent set it a long time ago but you hold the menu button on the steering wheel and its one of the options. Ill show everyone how to do it on my next rx8 video
@@seanhaight3939 yeah it's a shame you have to do that tho, it would be much easier to install an aftermarket exaust if you didn't have to go do all these extra precautions. I don't mind tho, I love my rx8
@@seanhaight3939 to your defend, this is my second rx8 since I sold my first one due to having kid. Regretted selling so I got my hands on a second rx8 8 years later. Cheers
Charles Strain I sold it to get some cash to buy the rx8 and another project car for the future. Im going to buy another brz in like 6-8 months once the cars I currently have are finished. Theres alot of stuff going on right now that im trying to plan out for future videos
Yeah its not a supercar so it takes a while to get up to speed on a 60mph road. It sounds good and is fun to drive so high hp acceleration isnt the goal for my rx8 haha
Carlos A. Lopez Its not for sale right now haha. I plan on keeping this car a while and putting alot of mods on it. If i change my mind ill let everyone know in one if my videos and you can buy it 👍
Let me know of any others that have low miles like that. Used to live in tampa, fl now I'm in los angeles, Ca. And it seems all the ones listed on autotrader and cargurus that are s2 rx8s or even s1, and they want way too much for them(the dealers and private individuals). And insurance companies won't give you what they're worth if totalled or stolen. They wanna give me Kelly Blue Book Value.
Carlos A. Lopez Yeah the cars in florida are pretty cheap and theres alot of cheap rx8’s. I just sold my series 1 rx8 for $1,700 because i lost interest in it and the new engine wasnt completely hooked up. The s2’s are going for 7-9k though. I found mine for a steal and went out and bought it. Ill keep my eye out for one for you!
@@seanhaight3939 Appreciate it! Looks good. Ended up buying a 2005 with 24,000 miles on it still smells like beans new but paid 10k for it velocity red about a month ago. Wanted to stay on the safe side with the low miles.
sniperyoassboi Yeah i thought the same thing. This video is with a cat delete and resonator delete. Watch my next video on the resonator install. The car sounds alot better with one.
its not an rx8 without a check engine light and a fuel light on.
I can't tell if you're being snarky or comical, but yes. The cats kill themselves, then the motor strangles to death soon after. Best to just remove the cats before your floorboards melt.
not sure if you guys cares but if you guys are bored like me atm then you can watch all the new movies and series on Instaflixxer. Been streaming with my girlfriend recently :)
@Ellis Cameron yup, I've been using InstaFlixxer for months myself :D
Damn mine isn't a real rx8 yet then lol
I was waiting for that redline shift and you came through in the end. Very nice
nice i got one on mine a lot of people tell me i need two pipes but ive drove mine for 7 years and she still braaaaps 04
150,000 + miles also make sure you keep gas in it. mine stayed on empty constantly and i had to put a fuel pump in
Badass exhaust sound, thanks 4 sharing.
I just got a rx8 about a month ago and I’m hoping to get it all fixed up and get this exhaust got it as a project for 1600 and it’s bone stock needs a lot of work but has potential
Same here man but I’m excited tbh
Nice video dude. Gonna watch more of your rx8 context for sure.
Wow that thing is clean!!!
Does your midpipe hiss at low rpm’s like air passing through? Mine does idk if it’s normal or exhaust leak, got a different gasket still same sound…
Did you have to modify the hangers for the hks exhaust to fit the s2? I’ve heard people say they cut the exhaust shroud because the exit pipe touches it.
It just needs a longer hanger. It's like 10 bucks. No need to cut into the body.
Sounds just like yours just with insane spooly boi noises
I would check it doesnt run lean sean after putting that exhaust on.
I put the toyo sport manifold, decat pipe (no resonator) and back box on a series 1 and it ran lean. Needed a remap or stand alone chip maybe would have done it.
Your S1 will run if its got more than 5 bar compression at whatever turn over speed you got. If you put the 2 kw 14 tooth pinion starter on plus an upreted battery e.g 680 CCA it will spin over at 350 to 400 rpm and move up the compression curve to get it started.
David rx8
Thanks for the advice! The s2 seems to run weird since the exhaust install and my gas mileage is terrible lol. The s1 has a new remanufactured engine but the starter clicks and wont turn the engine over. It tested good but i think the starter isnt getting enough power or something? I need to look into it soon. But yeah i plan on getting the s2 tuned to get rid of the cel and get the car running smooth again!
Hi sean, if you put a 200ohm resistor (which will cost next to nothing) in line to the coolant temp sensor it will fool the ecu into thinking the engine is cooler than it is and the map settings will be there fore be richer on fuel and idle speed will be about 1000 rpm. Its a cheap way to remap it. But the fan wont cut in until later so if its hot or you are in traffic watch out for this. You can overcome it by turning the a/c on which causes the fans to run or put an aftermarket fan temp kit on which consists of a temp sensor in the top hose with an adjuster unit. Without a Cobb access port its one way to change the map settings.
I put the exhaust on my S1 and it lost the power it gained if that makes sense due to running lean - plugs were white.
I can give you the wire colours and where to splice in if you want to try it.
I am in UK and have had loads of rx8s. over here we have an s1, the s2 is not like yours it is an s1 with no plastic on the seat backs and different ecu software. I also have an R3 which looks like your s2 but with a body kit with rear spoiler, 19" wheels other mods such as extra oil injector on apex seals, recaro seats etc
over here the rx8s are cheap to buy as what we call the road tax is £600 per year (maybe $750) and fuel is £1.40 per litre so they are expensive to run. But the rx7s are expensive and a silver one like yours about £10,000 minimum without the engine.
@@seanhaight3939
@@seanhaight3939 forgot to say check the engine earth and clean it up on the S1. It is the main earth for the starter and located below the spark plugs just above the sump pan join. It bolts to a bracket that also unbolts from the engine so 2 connections to go bad.
David rx8
Yeah man ill try that later this week and see if it fixes the starting process on the s1. As for the s2 there is an ecu reflash that i can get for $180 that turns the fans on sooner, gets rid of the cel, raises the rpm to 950, and says itll get better mpg also. Seems like a good deal!
What test pipe you used?
Fucking sweet dude! I want one XDDDD keep up the great vids man!
Casey Bunter
Thanks for the positive support man! I filmed a few new videos and im editing them tomorrow. Stay tuned for the new mods!
Sean Haight SWEET! I CANT WAIT TO SEE THEM! by any chance could you tell me the exact exhaust kit this is or a link to where I could purchase it? I love the way it sounds thanksss
Casey Bunter
31006-BZ001 - HKS Hi-Power Exhaust
Google it and you should be able to find a websites that has it on sale!
Did you have to plug in the O2 sensor somewhere. Or will that affect anything?
If you keep your stock midpipe you wont need to change anything but if you buy an aftermarket midpipe then they have a screw in location for the O2 sensor but because there isnt a cat on the aftermarket pipe, it will throw a check engine light. Its way better for rotary engines to not have a cat so definitely delete it if your state doesnt make you have one. I have a video on rx8 midpipes so itll show you everything.
Your rx8 sounds especially raspy?
Did you get rid of your cat converter aswell?
Yeah i put on a full hks exhaust with a cat delete and a resonator delete and it opened the car up alot. In the next video i installed a different midpipe that was catless and had a resonator. If you dont have a resonator the car is super raspy over 4k rpm. I recommend them for sure! I describe all the benefits and differences in that video. Sounds way better!
Hi does the hks come as a cat back or did you weld it to a mid pipe?
The kit is a catback and it doesnt come with a resonator. If you buy the other single exit hks exhaust for the rx8, it comes with a resonator. The tips and muffler position are different for both kits. In this video i installed a catless and resonatorless pipe but the next video i uploaded has an aftermarket catless pipe with a resonator on it. It sounds much better with a resonator lol
Ok. I was just trying to make sure before I purchase the hks hi power that it runs from the cat back. I thought it ran from the headers back deleting the cat.
@@josephbassil4171
I looked online and never saw a kit that has it. The hks kit isnt too expensive for such a good quality exhaust so with the cat delete pipe, the entire exhaust may cost around $750. Not too bad!
hey i see you dont have a oil temp gauge on the dash. is that an american model thing? mine in the EU has it standard
Im not sure? Most cars in American only have an oil pressure gauge. My genesis coupe has an oil temp gauge and it's super helpful. I wish my Rx8 had one because hot oil in a rotary is bad news! 😵
Im going to look into it and see if a European Rx8 dash cluster would work on an American Rx8!
It's standard on American models as well. Most likely that's not the original gauge cluster.
What? Oil temp gauge in the 8? First time hearing, it only has a fake oil pressure gauge.
@@neoney after these 3 years i actually owned one: there's just a indicative oil temp gauge. I installed a riser between the block and the fileter, and added aftermarket oil temp and pressure gauges
@@acvn-hg9gy The temperature gauge on the left is a coolant temperature gauge
Do you know how to fix a flooded engine for a 2009 sport rx-8
Oscar Amador
Yeah you have to turn the key into to the on position, without starting it, and push the gas pedal to full throttle until you hear a noise. The noise means the fuel is cutoff so it wont send anymore fuel. So with your foot on full throttle, turn the key to start the car and it will turn the engine over and it will pump out the gas from inside the engine. Do that for like 15-20 seconds and then take your foot off the gas and start the car like normal
Sean Haight ok thank you 🙏. And keep up the good videos.
How did you put your name on the dash board?
Oscar Amador
You can change it through the same settings as how you change the time. Scroll through the options and itll let you change the display title
@@seanhaight3939 I have a 2010 and can't find how to change the text? what series of button do I need to push? Thanks
It’s a metra kit. www.metraonline.com/part/Mazda_RX8_Dash_kit_95-7510
Dominic Blais
I havent set it a long time ago but you hold the menu button on the steering wheel and its one of the options. Ill show everyone how to do it on my next rx8 video
Sean Haight please I would love to see a video on that lol
What part of florida u from
Jose Torres
Tampa Florida 🤘
Nice car but where the check engine light
Problem with the rx8, with the rotary engine, it sounds very ricey with a aftermarket exaust.
Love the car tho
DeadTrendz
Thanks man! I made a video installing a resonated midpipe and the raspy honda sound is almost gone now. Sounds way better than before haha
@@seanhaight3939 yeah it's a shame you have to do that tho, it would be much easier to install an aftermarket exaust if you didn't have to go do all these extra precautions. I don't mind tho, I love my rx8
DeadTrendz
Same here man! Most people hate on these cars but I love them! Ill defend rotaries until the day i die. Such unique good looking cars!
@@seanhaight3939 yeah, they have legendary roots in racing too, love the rotary engine, such a staple in automotive history.
@@seanhaight3939 to your defend, this is my second rx8 since I sold my first one due to having kid. Regretted selling so I got my hands on a second rx8 8 years later. Cheers
Cop on the left @ 4:58 😂
Turbo the rx8?
Charles Strain
Sshhhhh 🤫
Future mods already ordered 😏 Top secret
@@seanhaight3939 do you still have the brz? Any plans for it?
Charles Strain
I sold it to get some cash to buy the rx8 and another project car for the future. Im going to buy another brz in like 6-8 months once the cars I currently have are finished. Theres alot of stuff going on right now that im trying to plan out for future videos
@@seanhaight3939 can't wait to watch your channel grow
@@seanhaight3939 you do anything else since the exhaust on the rx8?
Sounds nice but it seems it doesnt move so much, commuters rolling by while revving 9000 rpm.
Yeah its not a supercar so it takes a while to get up to speed on a 60mph road. It sounds good and is fun to drive so high hp acceleration isnt the goal for my rx8 haha
@@seanhaight3939 keep it up 👍
Is tat street legal ??
Sherab Loyal
Yeah but only in certain states that dont have smog testing and strict car modification laws lol
Wanna sell the car as is? How much?
Carlos A. Lopez
Its not for sale right now haha. I plan on keeping this car a while and putting alot of mods on it. If i change my mind ill let everyone know in one if my videos and you can buy it 👍
Let me know of any others that have low miles like that. Used to live in tampa, fl now I'm in los angeles, Ca. And it seems all the ones listed on autotrader and cargurus that are s2 rx8s or even s1, and they want way too much for them(the dealers and private individuals). And insurance companies won't give you what they're worth if totalled or stolen. They wanna give me Kelly Blue Book Value.
Carlos A. Lopez
Yeah the cars in florida are pretty cheap and theres alot of cheap rx8’s. I just sold my series 1 rx8 for $1,700 because i lost interest in it and the new engine wasnt completely hooked up. The s2’s are going for 7-9k though. I found mine for a steal and went out and bought it. Ill keep my eye out for one for you!
Carlos A. Lopez
facebook.com/marketplace/item/570040040200182/
@@seanhaight3939 Appreciate it! Looks good. Ended up buying a 2005 with 24,000 miles on it still smells like beans new but paid 10k for it velocity red about a month ago. Wanted to stay on the safe side with the low miles.
Turn your DSC off
its sounds rice to me are you sure its a real HKS part? it actually sounds like a dirt bike which is what a fart can sounds like.
sniperyoassboi
Yeah i thought the same thing. This video is with a cat delete and resonator delete. Watch my next video on the resonator install. The car sounds alot better with one.
@@seanhaight3939 ohhhh that makes sense i though you were done my bad will definitely check it out then.
it's a rotary that's what it sounds like
series 2 with series 3 face hmmmmm....
No such thing as a series 3 lol
can i have one lol
Im german☹️
Is being german bad? lol
Do you guys have rx8’s in germany?
I have the HKS exhaust with a turbo on my rx8, follow me on IG: rx8t_hunter
No gain over Exhaust for rx8 as there is -6 overlap! yes overlap is minus on Rensis engines. No resonance effect no.....
what kind of ignition system did you put into it?
Tucker Boomsma
I made a video on the ignition upgrade and install if you want to see it but its magnacor R100 wires and NP Boosted coilpacks