How to replace the Catalytic Converter 2009-2018 Dodge RAM 1500 🛻

Find the parts used in the video on CarParts.com just there carparts.solut...
⚙️ NEEDED CARPARTS AND PRODUCTS
- Catalytic converters : carparts.solut... and carparts.solut...
- Penetrating oil
- Exhaust sealant
💪 TIGHTENING TORQUES
- Oxygen sensors : 22 Ft-lbs
- Catalytic converter to Exhaust manifold nuts : 30 Ft-lbs
- Muffler assembly clamp nuts : 40 Ft-lbs
🛠 TOOLS
The toolbox recommended by CARPARTS.COM to repair your Dodge RAM 1500 :
- carparts.solut...
List of the tools we used to replace the catalytic converter on a Dodge RAM 1500 :
- Hydraulic jack : carparts.solut...
- Jack stands : carparts.solut...
- Wheel lug wrench
- Ratchet
- 8mm socket
- Flathead screwdriver
- Fork
- Extender
- 10mm socket
- Wire brush
- 16mm socket
- Sandpaper
- 15mm wrench X2
- Torque wrench :
20 to 250 Ft-lbs carparts.solut...
100 to 600 Ft-lbs carparts.solut...
Don't forget to subscribe : / @carpartscomofficial
🛻 COMPATIBLE VEHICLES
The operation and tools displayed in the video should be available on the following vehicles :
- 2009 RAM 1500
- 2010 RAM 1500
- 2011 RAM 1500
- 2012 RAM 1500
- 2013 RAM 1500
- 2014 RAM 1500
- 2015 RAM 1500
- 2016 RAM 1500
- 2017 RAM 1500
- 2018 RAM 1500
📽 🛠 USEFUL VIDEOS 🛠 📽
- How to replace the Battery 2009-2018 Dodge RAM 1500 ⚡: • How to replace the Bat...
- How to jack your Dodge RAM 1500 safely : • How to jack your 2009-...
- How to replace the Oxygen sensors 2009-2018 RAM 1500 :
⚠️ CARPARTS.COM'S INFOS
- We’ll show you how to remove the catalytic converter on the passenger’s side. The operation is similar on the driver’s side.
- To ensure a perfect seal during reassembly, clean the contact surface between the metal gasket and the engine block using fine sandpaper.
- Take the new catalytic converter on which we advise you to install new oxygen sensors.
- If you wish, you can coat the junction point between the catalytic converter and the exhaust line with exhaust sealant. It is not advisable to do this on the upper part of the catalytic converter.
🚨 DISCLAIMER
This video is for entertainment purposes only. Carparts.com, Inc. disclaims all damages including, but not limited to, actual, consequential, and/or punitive, for any liability, claim, or any other injury or cause related to or arising from any information or lack thereof posted in this video. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All mechanical car projects entail some risk. It is the sole responsibility of the viewer to assume this risk. If you are in doubt, please consult a licensed mechanic in your area.
📚 CHAPTERS
0:00 Intro
0:11 Disconnect the battery
0:39 How to pull up your RAM 1500
1:20 Remove the mudguard
1:51 Disconnect the oxygen sensors
2:41 Remove the cat converter from the engine block
3:07 Remove the cat converter from the exhaust line
3:38 Remove the cat converter
3:48 Sand the contact surface
4:07 Put the gasket back
4:30 Install new oxygen sensors
4:47 Put the cat converter back on the engine
5:33 Reconnect the cat converter to the exhaust line
5:54 Screw all the nuts and bolts back + tightening torques
6:30 Reconnect the oxygen sensors
6:58 Put the mudguard back
7:17 Put your RAM 1500 on the ground
7:28 Reconnect the battery

[@Dannydb0524]

I have a 2010 ram 5.7 and this is not like my truck you should said that’s only for non 5.7 hemi

[@emilyriggs5437]

I have a 2012 ram 1500 st 5.7 hemi and fhis is not my set up

[@CarPartscomOfficial]

Hello Emily ! Our RAM was a 2017 3.6L engine :/

[@champ6918]

Make a video with the hemi, most ram trucks are hemi.

[@CarPartscomOfficial]

Hi champ6918 ! The project is in the pipe 😁