How to Replace Front Lower Ball Joint 2006-08 Dodge RAM

Buy Now!
New Ball Joint from 1AAuto.com 1aau.to/ia/1ASB...
Modern suspensions combine a number of moving parts for safe and stable handling. The ball joint is the crucial moving component that ties those parts together. The ball-in-socket joint can wear out and loosen over time. Or, the rubber protective boot can tear, allowing contaminants to seize the joint. Bad ball joints are a common failure point on vehicle inspections because they lead to unsafe driving conditions. Fortunately, they are relatively easy to replace with the right know-how. This video shows you how to install new, quality TRQ ball joints on your 2002-2009 Dodge Ram 1500.
• Check here for more videos on the 2002-09 Dodge Ram 1500: • Dodge Ram 1500 3rd Gen...
This process should be similar on the following vehicles:
2002 Dodge Ram 1500
2003 Dodge Ram 1500
2004 Dodge Ram 1500
2005 Dodge Ram 1500
2006 Dodge Ram 1500
2007 Dodge Ram 1500
2008 Dodge Ram 1500
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oaVf/1A...
• Pry Bar 1aau.to/oFC/1AX...
• Ball Joint Press
• Brake Caliper Hanger 1aau.to/ofu/1AX...
• Straight Cutters
• 1/2 Inch Air Impact Gun 1aau.to/omF/1AX...
• Air Chisel 1aau.to/oaI/1AX...
• Ratchet 1aau.to/oa8o/1A...
• Socket Driver
• Socket Extensions 1aau.to/oaTH/1A...
• Swivel
• Torque Wrench 1aau.to/oafc/1A...
• Floor Jack 1aau.to/oLT/1AX...
• Hammer 1aau.to/oIA/1AX...
• Jack Stands 1aau.to/oJf/1AX...
• Wheel Chocks
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*

[@saulnierleo-paul2346]

2013

[@liquiddreamification]

I like how you snuck in the new upper control arm.

[@MadebyAmerica1981]

Need you to do a complete 3rd Gen 5.9 Cummins rwd. Maybe how to pull and clean the injectors would be nice and front ball joints. I know it’s lots to ask thank you.

[@philosopher8358]

Awesome presentation! I've always found it more time consuming to get the pressed in items out, as opposed to the rest of the job. Patience and of course the right tools for the job. If you don't take your time and try to rush the job, or don't have the proper tools, you can easily ruin the new part's, or create a more frustrating situation. As the saying is. Slow as she goes! 👨‍🔧💖

[@TRQ]

+philo sopher Thanks for watching!

[@heavyballs8458]

This actually helps with factory ball joint I didn’t know you needed to peen over the edges I was about to mess some stuff up!

[@josephgrecni6883]

Very nicely done! Clear and complete. Thanks.

[@phillmcgriff3226]

You are awesome brother, thanks

[@ottostigs7602]

Very good video! Thanks!

[@Oppsalot]

You didn’t give the torque on the axle nut. Why?

[@davidpeterson9507]

good stuff Is it easier to change the whole arm with the ball joint . Its about the same money ?

[@kbagz92]

Can you replace wheel bearings while you have knuckle removed? I just watched your video on the same vehicle on replacing wheel bearings and it seems as if you didn way more work vs just removing the whole knuckle.

[@davidm.1098]

wait a minute!! the "friends" guy left 1Aauto?

[@LTZ_Z71]

Nice video! I was cringing when you started hammering the hell out of that aluminum knuckle.

[@TRQ]

+M T Thanks for watching our video! 1aau.to/m/Shop-TRQ

[@mikemahoney6351]

@@TRQ Just had mine replaced. Mechanic hit knuckle, cracking knuckle $600.00 later fixed. Did this because of squeak. Expensive squeak.

[@3dp_edc]

been beating on my knuckle to try and release the upper since yesterday afternoon lol it was replaced earlier this year dont get why its so stuck.... need to do the lowers but this is preventing me any suggestions?

[@markballard1515]

What to do when you way overtighten ball joints?

[@ArmenArmenjs]

Nice presentation! uhh I saw the bottom of the C clamp cup wasn't seating straight, otherwise press would have taken out no problem. You couldn't see it from top. I have the same BJ on 2004 Silverado 1500 and it's Original BJ. the lower CA, BJ is stacked just like what you did. ☺

[@saulnierleo-paul2346]

2013

[@jonathanbowe4589]

So why is the labor on ts 900$

[@donjoh4464]

I like how he said bonk but then hit it full force lol

[@merlepatterson]

38 ft/lbs on a lower ball joint?

[@earlmiller6093]

Dude…. Nice work… however I just changed mine… yeah, my press along with torch still didn’t push it out… I ended up cutting the top off the lower ball off… drilling a hole thro it , pounding the ball out, cutting the side out with a sawzall , and hammer and punch it out… the upper joints pressed out usual… the lower ones??? Hell no!

[@CrimsonArchon]

By bonk he means hit it so hard your neighbor feels the shock wave

[@patscarborough9183]

Warning: I have a 2009 Dodge Ram 1500 2wd. The lower ball joints CANNOT BE REMOVED OR REPLACED!!! You will need to replace the lower control arm - they are around $100 per side with ball joint included.

[@TRQ]

+Pat Scarborough Thanks for the feedback! 1aau.to/m/Shop-TRQ

[@daman737]

Is it cause they're welded in ?