Have a great video. Perfect and excellent work. Your demonstration is very nice sir . Keep it up and great job 👍💪👌❤️❤️❤️❤️ I learn a lot form this video
my lucky day so much good content to see today, u, rick, Chris, awesome, thanks for the tips, work on these units a lot. and about the haircut, i feel you man, had to go bald :))
Last time i ordered up a new accumulator for a true prep table, the bottom wasn't completely crimped or soldered shut. Could see daylight through it 🤣😆🤣😆🤣Such a pain to replace the evap and accumulator, can never get them to fit perfectly without screwing up the sheet metal. Good job bro. Glad to see you still rocking the facemask. No one here in Illinois seems to give a rip about safety with the covid anymore. I feel defeated wearing mine when no one else wears theirs.
I do exactly the same procedure with my manifold and the vacuum pump - pull out the contaminants while vacuuming the system. Great video Dave, thanks! Btw, you’re starting to look like Sammy Hagar with the hair... I’m starting to look like Dave Grohl... 🤣
In every vehicle I ever owned that had A/C..., I mean I plead the fifth😉 I just finished a TUC27 here in Westland. Set at #1 the evaporator coil was freezing up. Replaced the cold control and now it's behaving real nice again. Cut in is a little high, but I was told to not rewire the True evaporator fans any more🤨😠
Yeah I also abandoned the accumulator because it didn't come with my new evaporator. Also ordered a cap tube cutter. I was using the file method for cutting cap tubes. Yes to screw the new normal. Good job
I just insulated the suction line, accumulator, and expansion line (past the metering device) all with 1/2” foam lineset insulation & 557 Duct tape... 2004 Silverado LoL
You dont have time to wait when you are the company. When you work for a company you have all the time in the world. Big difference hence better tools. Rock on Dave.
Oh sure, I keep my standalone temp probes in the air vents on my truck. Helps keep 'em from wandering off, unless I launch it too hard. I will probably never find myself replacing an evaporator in a True make up table, but at least now I have some idea what's involved.
If there was 1 cooler mfg I despised working on in my 17+ years doing commercial refrigeration it was "True" .I have done this repair on this model more than once. R-12 & R-134a. a good tech with normal brazing skills could make the connections in the box.
Good stuff.. the refer man is knocked dead again. Hair cut.. no way grow it to the knees..dont be a quitter..lol. be safe have a great night brother Dave.
Looks like it’s ready to loose a caster wheel too. My tubing cutter goes around as few times as possible, I got shit to do lol. I broke the door off my VP-85, I called Field Piece to order a replacement door and they told me no problem and shipped that day and didn’t charge me. A standup company. You need a Flobee for your hair.
Hi Dave, I have a True T-15G Refrigerator and the condenser pipe insulation looks melted. Almost like black tar. It even dripped down to the water collection tray. Thoughts? Would love your opinion. You’re a very smart professional when it comes to these things. Liked and subscribed!!!
great channel.. If a fridge is not cooling but the first 6 inches or so of the cap tube is completely icing over, where would you start? Condenser coils are clean. It worked a month ago when I plugged it in and it has been sitting off till last night..
I've seen some leave the pressure on the suction line at 4psi, but you always leave it at 18psi when working with r134a. Could you please help me understand what is the correct pressure?
I love this guy's stuff I have a question. I'm a ten year Tin knocker and recently was stolen to a new company doing service just like this. What is some really good advice? I'm older and very nervous it's like starting a new trade pretty much and I have a lot riding on this job
How do you get the customer to go for a new coil/t-stat here in New York if the coil a leaker never would a customer go for replacement as the cost to repair/replace after all said and done (labor cost) it's really in their best interest to buy new and warranted...but more power to u
If you weren't all the way in Cali I'd fix it for ya for free brother. Anyway, keep them videos coming. I'll hold down the Florida cold and hotside while doing my custom paint for restaurant equipment.
Your like Monet with that torch Super Dave... Lol ...Send a pic of you at the end to Pelosi and she'll open every salon in California ... Lol ... good vid ...
Question: on these small ass units that take charges of less than 1 lb - how do you know if you have weighed in the correct charge? My scale says 1 lb but that is the difference at my scale. There is refrigerant in my hoses and manifold - WTF chuck?
Thanks for being us along! I agree with the underground hair cutter! I need it too! Nice Job! 👍
Nice job Dave! Thanks for showing all your work for us newbies.
Thanks for watching Dennis.
@@NorCal-refrigeration 10:24
That evaporator must be taller than it looks, I kept waiting for you to set the table on 🔥
David I enjoy your videos !! Thank you so much to take the time to make them@!!!
Exelente trabajo lo felicito desde la distancia saludos desde Argentina
Great job Dave!!!
Thank you
Gave myself the buzz cut with #1 guard in the yard back in March and used the leaf blower to shake it off... grew out pretty good!
Epic
Good job.you make everything look so easy
Nice repair Dave, keep the videos coming bro 👍
Good video Dave as always 👍
Thank you Dave I love it
Have a great video. Perfect and excellent work. Your demonstration is very nice sir . Keep it up and great job 👍💪👌❤️❤️❤️❤️ I learn a lot form this video
Paging Dr. Nor-Cal, paging Dr. Nor-Cal, you have a major surgery scheduled. Great repair Dave!
Sup skid!
Thanks Lex!
U DA BEST DAVE!! Much love from southeast Louisiana
Thank you Alexander 🤘⚡️🤘✨✨
Awesome work there ! 👍🏻
Love the videos man. Keep em comin
my lucky day so much good content to see today, u, rick, Chris, awesome, thanks for the tips, work on these units a lot. and about the haircut, i feel you man, had to go bald :))
I love this guy man great content bro!
Thank you
Great video. Good job. Thanks
Diamond Dave for the win again!
Soy tu fan soy estudiante de refrigeracion
Great video. I think everyone forgot how to drive from being locked up. When i first got in my truck i felt a bit off ....lol
Very true
Thank you for this great vedio
Finally got my hair cut yesterday! In NC you have to ware a mask, but they are open as of last week. Go ahead and start your dreadlocks Dave
🎶 The RUclips police🎶😂. Love that you played the song when you were brazing the coil.
🤣😂🤣😂🤣😂
Last time i ordered up a new accumulator for a true prep table, the bottom wasn't completely crimped or soldered shut. Could see daylight through it 🤣😆🤣😆🤣Such a pain to replace the evap and accumulator, can never get them to fit perfectly without screwing up the sheet metal. Good job bro. Glad to see you still rocking the facemask. No one here in Illinois seems to give a rip about safety with the covid anymore. I feel defeated wearing mine when no one else wears theirs.
County regulations here. Have too.
@@NorCal-refrigeration us too. Signs on every entrance. No one cares and no one mandates it.
Great video's.
I do exactly the same procedure with my manifold and the vacuum pump - pull out the contaminants while vacuuming the system. Great video Dave, thanks! Btw, you’re starting to look like Sammy Hagar with the hair... I’m starting to look like Dave Grohl... 🤣
In every vehicle I ever owned that had A/C..., I mean I plead the fifth😉
I just finished a TUC27 here in Westland. Set at #1 the evaporator coil was freezing up. Replaced the cold control and now it's behaving real nice again.
Cut in is a little high, but I was told to not rewire the True evaporator fans any more🤨😠
Gonna plug up that brand new cap tube with carbon flakes Dave! 😱. Nitro flo bro 👍
Btw love your videos dude, I’m working my way through them all!
thank you My friend
Yeah I also abandoned the accumulator because it didn't come with my new evaporator. Also ordered a cap tube cutter. I was using the file method for cutting cap tubes. Yes to screw the new normal. Good job
Right on Frank
Is that blonde Johnny Depp? Naw this guys actually working and sober!
I just insulated the suction line, accumulator, and expansion line (past the metering device) all with 1/2” foam lineset insulation & 557 Duct tape... 2004 Silverado LoL
Lol always I'll do it with my kids sometimes say really dad. 😂😂😂😂 keep it up my man.
I felt silly rolling in a dodge caravan until I parked next to an Astro van the other day, dam that thing was basically the same size.
Much longer on furlough and my Chevy Venture that has been gathering dust is about to turn into a SideJobBob Mobile!
You guy's with you're fancy vacuum pump lol I don't need that just give me something that can pull down to 500 and am good ! Awesome job by the way 👏
They gave it to me. The least I can do is use it. 🤘⚡️🤘
@@NorCal-refrigeration Hey can't argue with that ! Id use it to :)
You dont have time to wait when you are the company. When you work for a company you have all the time in the world. Big difference hence better tools. Rock on Dave.
Astro van brake light illuminated, I stick my digi down the A/C vent all the time bro!
ABS module is bad. But the van runs great.
Ive run my temp gauge a few times out here during the hot part of summer....always nice when its 120* out and the truck AC is running 48* at idle
That is a good feeling.
Oh sure, I keep my standalone temp probes in the air vents on my truck. Helps keep 'em from wandering off, unless I launch it too hard.
I will probably never find myself replacing an evaporator in a True make up table, but at least now I have some idea what's involved.
If there was 1 cooler mfg I despised working on in my 17+ years doing commercial refrigeration it was "True" .I have done this repair on this model more than once. R-12 & R-134a. a good tech with normal brazing skills could make the connections in the box.
Good stuff.. the refer man is knocked dead again. Hair cut.. no way grow it to the knees..dont be a quitter..lol. be safe have a great night brother Dave.
Like ALL y'all missed the giant nug of weed on the restaurant floor at 2:01?? lamo 😂🤣
Looks like it’s ready to loose a caster wheel too. My tubing cutter goes around as few times as possible, I got shit to do lol. I broke the door off my VP-85, I called Field Piece to order a replacement door and they told me no problem and shipped that day and didn’t charge me. A standup company. You need a Flobee for your hair.
Yup I do in both my work truck and personal car
"no no no....you no make video.....customer will see how dirty my place is..." 🤣🤣🤣🤣
Shit, you got me. I went so far as to using the vent to hold my pencil psychrometer. Gotta make sure that she blows cold and dry.
Hi Dave,
I have a True T-15G Refrigerator and the condenser pipe insulation looks melted. Almost like black tar. It even dripped down to the water collection tray.
Thoughts? Would love your opinion. You’re a very smart professional when it comes to these things. Liked and subscribed!!!
Vangina! Still keeping her cool!
I go about 90 - 95 to cool my truck down. Az is hot bro.
keep it long bro. you look like a true californian.
Cool!
Yeah Dave I do that also and also with the thermistors 🤣
You guys get everything to replace for me I will have to clean up and repair that evoparator
That was just me this week: beanie hat , head lamp , kneeling mat , long scruffy hair 😆😎😷
I cut that suction accumulator on reach ins too. Those things tend to leak all the time.
Fantastic job 👍👍👍👍 Geraldo lmao 😂 😂😂😂
That was epic.
Does the bottom part of that fridge slide out? Like where the compressor is
great channel.. If a fridge is not cooling but the first 6 inches or so of the cap tube is completely icing over, where would you start? Condenser coils are clean. It worked a month ago when I plugged it in and it has been sitting off till last night..
Possibly low on charge
Master......
I have 2019 Silverado don't have to worry about it.
I've seen some leave the pressure on the suction line at 4psi, but you always leave it at 18psi when working with r134a. Could you please help me understand what is the correct pressure?
Hey Dave what torch tip are you using?
This guy is a true gangster. Who the hell brazes on a dinning table?:)))
I have done it sir.
I love this guy's stuff I have a question. I'm a ten year Tin knocker and recently was stolen to a new company doing service just like this. What is some really good advice? I'm older and very nervous it's like starting a new trade pretty much and I have a lot riding on this job
Just be thorough and check the whole system. Multiple offenders are on most units. 🤘⚡️🤘✨✨
Nice
👍👍
When I replaced the evaporator I change the suction line to. No soldering in the box that way
If I had a van I would lol!
What was that you cleaned while vacuuming the system?
Condenser coil
The jobs look good but I want to know how you able to tell the customers what will cost
good
I recharged my work van.
How do you get the customer to go for a new coil/t-stat here in New York if the coil a leaker never would a customer go for replacement as the cost to repair/replace after all said and done (labor cost) it's really in their best interest to buy new and warranted...but more power to u
They wanted to fix it. I was trying to run away from it. Lol
Looks like you were driving with the emergency brake on.
Abs module has loose solder connections
Are you low on brake fluid,your pads are wore, or did you leave the parking brake on?
Abs module loose solder connections I need to fix it
If you weren't all the way in Cali I'd fix it for ya for free brother. Anyway, keep them videos coming. I'll hold down the Florida cold and hotside while doing my custom paint for restaurant equipment.
What is the size of the capillary tube did you use please and if a prep table 2 doors how can i size it
I like your cap. Where can I find one? 😅
21:02 yeah bro I live with the headlamp I need light in those dark corners
Can’t work with out it. Lol
tip of the day @ 11:23 and don't burn their tables lol
I’m a brazing wizard no tables injured during this filming.
Good little rebuilt Dave . @ 6:30 the YT 👮🏼♀️ watch out !!!
I thought you have to braze with nitrogen because of oxidation and carbon? Is it not necessary to run the nitrogen through the lines as you breeze?
Please, what kind of recovery machine do you have?
Navac
I can't believe you have the confidence to braise over their Dining Room table. Who is better then the Norcal Man?
Your like Monet with that torch Super Dave... Lol ...Send a pic of you at the end to Pelosi and she'll open every salon in California ... Lol ... good vid ...
A little Three Flowers in that hair, good to go
U got me. Lol
You got your emergency brake on buddy!
No my ABS module has loose solder connections and in to busy errrrrr lazy to fix it. 😂😂😂😂😂😂😂😂😂😂✨
I noticed you removed the accumulator don't you to have one on coolers and freezers ?
Taqueria Santa Cruz on mission st. Santa Cruz, ca
was that a customgrow intro reference?
Question: on these small ass units that take charges of less than 1 lb - how do you know if you have weighed in the correct charge? My scale says 1 lb but that is the difference at my scale. There is refrigerant in my hoses and manifold - WTF chuck?
It’s a base line then look for a 20 degree evap and compressor amps.
Bam busting my balls 🤣
Is the evap coil also called an expansion coil? The gas 'expands' in the coil, it doesn't 'evaporate'. Just wondering.
Not had a hair cut for years, just tied back in a pony tail, meanwhile everyone else is looking like they're from the 1970's haha.
I've had one setting for my clippers and usually throw away all accessories for the last 20 years.
Yea bro I do that too I think she needs a little shot of juice. Ask jonhvac about it you prolly want to do a total evac and Recharge with good Vacuum
In the plans
Buzzcut bro - go military style
I wouldn’t have put that much money into that cooler. That one goes to scrap cuz next week the compressors gonna fail....
right? captube already replaced, suction accumulator removed, who knows how long the compressor will last
Blinker fluid probably low 😂😂😂😷