Waterproof Wire Connectors
HTML-код
- Опубликовано: 24 сен 2022
- Do you need to connect wires in your car, or your boat, or wherever it is wet?
Look no further! There are great connectors out there in the Amazon and Ebay. Let me show you how this works ...
Questions and concerns in the comments below! 
Хобби
I like the fact that the video has some errors in connecting them. Really life applications.
Great video, actually nice to also see how it can go wrong so I don't have to discover that the hard way!
Good tutorial - I like the trial and error, not many videos show mistakes and recovery 👍
Thank you your instruction is very clear, and at a speed which I can keep up
I was getting so frustrated trying to fit these. Encouraged to see that it wasn't just me, they are very difficult to get all lined up. Great connectors once they're complete, but tricky to put together.
i was also discouraged to fit my motorcycle DIY, LED modification using these connectors, then went to the garage instead.
I add a bit of vaseline to the fittings which gives it a little better seal and keeps them from sticking if you have to disconnect them later.
Thanks for the very helpful video, and for making my mistakes in advance !
Very helpful thankyou saved me all the trial and errors
Excellent video
This was perfect and exactly what I was looking for. Thank you so much!
I personaly apply liberal amounts of the anti corrosion liquid called ACF50, both to the stripped wire end so it wicks down the copper strands, and to the silicon seals. It is a bit like WD40 on steroids, and is used as an anti corrosion film on aircraft and mototcycles. I also noticed that you had the ears that wrap around the seal get crimped in the same way as the copper, in that the ears got folded inwards on themselves. It is usual to have the seal ears overlap one another and get gently squeezed so that they form a circle around the outer part of the seal.
Remember that when the connectors are separated water can get into the vital pins, so if you also give the internals a squirt of ACF50 and the water gets in, it will not be able to get to the metal of the pin and cause havoc ✅
Very helpful video. Thanks for your help.
Well done, S 11:24 ir and thanks - tricky work! 👌🏻
Nice video. I will say that a little diaelectric grease goes along way when making these connections.
Great information
Brilliant, thanks.
Very helpful, thanks!
Thank you !
Waterproof = impervious to water. I’ve used plenty of these and consider them to be water resistant = able to resist the penetration of water to some degree but not entirely.
yeah i just put together a 3pin connector as a test and found water inside after a submerge test. not great, but cheap, not something i would use on a car though
@dudekidPL what would you use? I have a jeeps, and want better water resistance....
@@itchy7727 You could try using a self-fusing tape, like "Tommy Tape" Electrical insulation and used to fix pipe leaks. However, you wouldn't be able to undo the connection again as the tape chemically fuses to itself. Brilliant stuff!
what kind of a crimp tool did you use?
By 7:10 I knew I rather stick with Anderson.. Hahaha.. I'll pass on water tight.
Hi, thats pretty detailed for me. But do you know how much power it can handle??
The ones i use in my video have the follow specs (I don't know if that's true, but that's what the Ebay seller writes)
Suitable for Cars, Motorbikes, Trucks, Caravans, Boats and other Marine Vehicles
Rated Voltage: 300V
Rated Current: 12A
1.5mm Terminal
Pin Number: 1/2/3/4/5/6
Working Temperature: -25~85 Degree
Waterproof Class: IP68
Material: Plastic
if i had to waterproof one I silicone it. thanks for the video great tips
once you silicone it you can't disconnect again. A connector is there to be able to do that, otherwise you wouldn't cut the wire.
@@mygiguser I presume the gentleman above meant silicone paste/grease, as in dielectric silicone grease, not the silicone sealant variant.
Can you please tell me what tool is needed and how to remove the pins thank you
YOu remove the red plastic lock piece, and then push the pins back with a screw driver, or pull on the wire.
What crimping tool do you use / welche Crimpzange haben Sie verwendet?
ruclips.net/video/JQml6R9f-4c/видео.htmlsi=V9nQd1p9wHMa1wM2
Hi sir, minute 12:31 after red plastic goes inside we can hear click sound means it has been locked. How to remove back/take out the red plastic out of the housing?
Watch Series 1 Episode 2
My red things inside the one side of connecters are all already locked into place in the kit i got so i cant get any of these to lock properly
I find if I place the pin in the tool and click it to the first locking point it holds the pin in the tool correctly while I align everything else hassle free
I would twist the wires together
that's bad when you crimp.
@@mygiguser Why crimp? Just twist
how do you depin these?
you need a tool for that. i can't find mine.
@@mygiguser any videos, you know of showcasing that
Were did you get the crimping tool?
ruclips.net/video/JQml6R9f-4c/видео.html
13:26 @@mygiguser
"The crimping always goes smoothly" and other fairy tales...
what do you mean? are you saying i faked those crimps in the video. They were all top notch!
@@mygiguser I mean always something goes wrong with crimping, it was a joke..