First of all, I apologize for my poor English. I have a similar problem with my V15. It works like this and then stops, but after doing this 3-4 times, it continues to work without any problems. Then I stop the machine again and take a 1-minute break and it works without any problems again. But if I take a 15-20-minute break and do not start the machine, it starts to have the same problem again. So I think the machine returns to normal after working and warming up a little. If we take a break and let the machine cool down, the problem starts again. What do you think could be the source of this problem? I have been researching for 1 year but I could not find a solution.
V15 detect with similar issue. Display reads fine but machine stops after a second on all modes until after 6-8 attempts and then runs fine on Eco and Auto, but no good on Boost. Bought a new head unit but will try and disconnect the display and see if it cures this one, can always use if for upstairs 🤞🏻 Great video, many thanks, new subscription 👍
Hello, you might find this helpful. I had a similar problem with my V12, after starting, it would turn off immediately. Only after 5-6 attempts of starting and stopping would it finally run continuously. The issue was with the three capacitors on the motor board. On mine, the capacitors are marked as 1N2 270 VHC. I discovered that they are 270 µF, 35 V hybrid capacitors. I replaced them six months ago, and I haven’t had any issues since then.
There are several possibilities: defective electronic board, defective motor, defective battery. Unfortunately, I cannot tell you for sure what the defect is in your case.
Hi! I'm subscribed to your channel, I read that many slim v12s turn off after a few seconds. It happened with mine too. Can you make a video or tell us the problem?
I am on my second v11 and the first one had this issue. The trigger was broken. It didn't have enough strength to push the button on the battery when I pressed it so it did this until it just didn't make a sound even anymore. Now my second one has this same issue starting today. They replaced the last one thankfully since it was a thousand when I bought it when it first came out. Not sure what it's at now.
Honestly, in this case I think it's the user's fault, the display is broken because it was hit or fell. It doesn't really happen that the display cracks by itself.
@@techfixPOV True, but in your case it looked like the display was fine, until you take a closer look and there is some bleed in it. In my view it's quite bad design that a faulty display (which seems to work anyway visually), can break an otherwise good product. I seem to see many V15's with this issue or the replace filter one like you have in your other video. There seems to be more issues compared to the older generation. Anyway hopefully more videos like yours helps get solutions for different fixes. Thanks.
@Naz546 Did the problem appear after you changed the button? You probably didn't mount something right. Make sure you mount that little white connector correctly.
DAYSON COMPLETAMENTE INCAPACI MA PARLANO INGLESE! Dayson aspirapolvere senza fili che si rompe facilmente: I progettisti Dayson sono dei DEMENTI, se monti l'elettronica a bordo motore per di più saldata rigidamente tramite i contatti dello stesso motore, portando di conseguenza tutte le vibrazioni e le risonanze del motore che ruota a 110.000 Rmp sull'elettronica, è normale che prima o poi si scassa, lo capisce anche un bambino, di fatti è il guasto più comune in pochi anni di vita. Con quello che costa questo aspirapolvere mi aspettavo un risultato almeno decente. Mi pare che più che aspirare polvere sia stata progettato solo per ASPIRARE SOLDI ai malcapitati che la comprano, di fatti è Britannica gli stessi che hanno fatto i vaccini insieme agli USA che fanno la Tesla!
Your closing remarks are racist and UNTRUE. Tesla is a 100% American company and produces cars in the USA, China and Germany. Please remove your racist and untrue statements. I do not want to have to report your comment. Thank you - and visit England and learn about the country. ...
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
First of all, I apologize for my poor English. I have a similar problem with my V15. It works like this and then stops, but after doing this 3-4 times, it continues to work without any problems. Then I stop the machine again and take a 1-minute break and it works without any problems again. But if I take a 15-20-minute break and do not start the machine, it starts to have the same problem again. So I think the machine returns to normal after working and warming up a little. If we take a break and let the machine cool down, the problem starts again. What do you think could be the source of this problem? I have been researching for 1 year but I could not find a solution.
i have the same problem
the same problem without an answer
can someone help us?
Same here..
Same same
V15 detect with similar issue. Display reads fine but machine stops after a second on all modes until after 6-8 attempts and then runs fine on Eco and Auto, but no good on Boost.
Bought a new head unit but will try and disconnect the display and see if it cures this one, can always use if for upstairs 🤞🏻
Great video, many thanks, new subscription 👍
Glad it helped!
Updates ?
Any news? I have a same problem with my V15
Have the same issue, have you fixed it?
@billywatcheseverything4108 have you managed to fix it?
This worked on my v12, exact same oroblem, thank you so much, now to dind a new screen...
Did you ever find one? I'm running mine without the screen right now
Would be also interested:)
Hello, you might find this helpful. I had a similar problem with my V12, after starting, it would turn off immediately. Only after 5-6 attempts of starting and stopping would it finally run continuously.
The issue was with the three capacitors on the motor board. On mine, the capacitors are marked as 1N2 270 VHC. I discovered that they are 270 µF, 35 V hybrid capacitors. I replaced them six months ago, and I haven’t had any issues since then.
Thanks for the tip!
Hi, is it possible to replace the three hybrid capacitors with classic electrolytic capacitors?
I have the same issue with my V10, stops immediately After 1 second. But it doesn‘t have any display. Any idea what could be the Problem?
There are several possibilities: defective electronic board, defective motor, defective battery. Unfortunately, I cannot tell you for sure what the defect is in your case.
Can you make a video to fix the defect motor?
Hi! I'm subscribed to your channel, I read that many slim v12s turn off after a few seconds. It happened with mine too. Can you make a video or tell us the problem?
Up))
Hello. Could you please make a video how to fix the Dyson v11 motor that turn on 1 second then stops ? ( motor issue not pcb board issue)
I am on my second v11 and the first one had this issue. The trigger was broken. It didn't have enough strength to push the button on the battery when I pressed it so it did this until it just didn't make a sound even anymore. Now my second one has this same issue starting today. They replaced the last one thankfully since it was a thousand when I bought it when it first came out. Not sure what it's at now.
Have the same issue with a V15, the newer Dyson tech is just getting worse and worse.
Honestly, in this case I think it's the user's fault, the display is broken because it was hit or fell. It doesn't really happen that the display cracks by itself.
@@techfixPOV True, but in your case it looked like the display was fine, until you take a closer look and there is some bleed in it.
In my view it's quite bad design that a faulty display (which seems to work anyway visually), can break an otherwise good product.
I seem to see many V15's with this issue or the replace filter one like you have in your other video. There seems to be more issues compared to the older generation.
Anyway hopefully more videos like yours helps get solutions for different fixes. Thanks.
Please in french ! ! Thank you
I have a solid red light on my v10 after changing the trigger what could the possible problems?
Short circuit
Replacement for a new charger as soon as possible. Do not charge with your luggage. The charger is screwed
I have the same issue by my v10, but this doesn‘t have a display. Any idea?
@Naz546 Did the problem appear after you changed the button? You probably didn't mount something right. Make sure you mount that little white connector correctly.
@techfixPOV yes it happened after changing the trigger. I triple checked everthing including that little white connector 🤷♂️
DAYSON COMPLETAMENTE INCAPACI MA PARLANO INGLESE!
Dayson aspirapolvere senza fili che si rompe facilmente:
I progettisti Dayson sono dei DEMENTI, se monti l'elettronica a bordo motore per di più saldata rigidamente tramite i contatti dello stesso motore, portando di conseguenza tutte le vibrazioni e le risonanze del motore che ruota a 110.000 Rmp sull'elettronica, è normale che prima o poi si scassa, lo capisce anche un bambino, di fatti è il guasto più comune in pochi anni di vita.
Con quello che costa questo aspirapolvere mi aspettavo un risultato almeno decente. Mi pare che più che aspirare polvere sia stata progettato solo per ASPIRARE SOLDI ai malcapitati che la comprano, di fatti è Britannica gli stessi che hanno fatto i vaccini insieme agli USA che fanno la Tesla!
isnt that black ring around the circuit board some sort of rubber gasket?
Your closing remarks are racist and UNTRUE. Tesla is a 100% American company and produces cars in the USA, China and Germany.
Please remove your racist and untrue statements. I do not want to have to report your comment. Thank you - and visit England and learn about the country.
...
Good job making the music annoying af
I'm glad you liked it. The song is called Last Train North if you want to set it as a ringtone. Have a wonderful day! 😄