HM10 BLE BLUETOOTH Module Part 1 -AT Commands on Original HM10

HM10 is BLE 4.0 BlueTooth LOW Energy module built on Texas CC2541 soc.
In this first part we shall explore the AT commands with the ORIGINAL HM10 module.
Clones are available widely as BT-05.
IBEACON is not possible on clone Firmware

[@umbertocera185]

Thank you very much sir.. This is the first time I understand why I get the Error message sending AT Commands

[@ray-zin]

Thank you sir, wonderful work!

[@solpcb]

Thanks, I found this very useful !

[@VMS_Electronics]

So informative sir 👍

[@jeevanandham2528]

Very useful video Sir..

[@jamesskelly5986]

very helpful, thank you

[@nickpelov]

Hi. Useful video. It would be nice to link the other parts in the description

[@chaminduyasitha6201]

Great video

[@arindammoitra3443]

I have a doubt is codes for Hm-10 and Hc-05 are different? Because already have project on HC-05 and if I now just replace this Bluetooth module to Hm-10 is this previous code work properly or I need to alter?
Last question Do i need power division in 3.3v for RX if I connect with Arduino Uno?

[@rossmurphy4593]

Helps lots. thanks

[@shakerileiwat4341]

Beyond great 👍♥👍

[@bharry1985]

Thank you sir.. This video is very helpful.. I want to know without level shifter this setup will work..

[@ashwinprabhu8418]

Sir is stm32 nucleo f103rb dev board is advisable for stm32 beginners? any suggestions?

[@eugenejayachandra5122]

After connection is estabilihsed using coolterminal, how do we request for UUID, characteristic and notofications thorogh same hyper terminal?
(We need to receive the periperal notifications in terminal)

[@fernandohood5542]

Excellent!!!!!!

[@feenicstechnics98]

Supper demo

[@basics7930]

Good video

[@SA-oj3bo]

Hi, how to set HM-10 so it can replace HC-05? We have Bluetooth classic MIT APP INV APP that works well with HC-05 but not with HM-10. So can HM-10 work as a HC-05 after setting it's parameters?

[@Onivlvino]

Can we make ble mesh using this?

[@madhavreddy1989]

Hi sir. Pls make a vidoe on how to use secondary UART on Raspberry Pi 4. I have gone through your video on enabling and swapping primary UART. But I need to use 2 UARTs simultaneously. Pls help

[@The28vicky]

Sir it is TTL output or serial output. Pls tell me

[@vishalgyanchandani4437]

When will part2 come out?

[@anilsonlino7036]

Heey. i tried to update my cc41 and it didnt come out of a wait screen. it was showing up on the scanners but now it doesn't show up but the led blinks. What do I do? I can't find you with any app

[@venkatyalamati3285]

Sir, plz tell where you purchased original hm-10

[@SateeshKushwaha-lc8iz]

setup application

[@mandalanaresh1522]

Hi sir tnxs for this vedio
Sir in this project shell we connect mobile bluetooth sir because our mobile is default master know is there any possibility sir

[@KandraTechinKannada]

Part 2 ?

[@LuisVazquez-kj1ym]

Hello, for me it works without resistance

[@chandru.c9268]

Hi sir kind and upload videos for TOP2013 universal programmer

[@sanjeevsharma-uf9ne]

Range

[@harunsaybakdof8673]

thanks for this video,
How can i remove the password?

[@SaravananAL]

AT+TYPE0 makes bond without PIN

[@aligul4035]

there no need of resistors