What Happens When You Apply a Rivet Nuts to Wood / Woodworking DIY
HTML-код
- Опубликовано: 21 сен 2024
- I tried applying the rivet (pop) nut used for joining thin steel plates to wood.
The test wood used was plywood, red pine, rubber wood, walnut wood, merbau, etc. The results were not suitable for soft wood (red pine), but good results for hard wood. If it is used for woodworking such as a knob, it seems to be easier to use than the existing nut.
What's needed is a rivnut whose expansion zone isn't adjacent to the top of the fastener, but closer to the end so it expands with more wood above it to provide pullout resistance.
with fangs that bite into the wood
I was about to say the same thing!
...or fit the rivnut on to the back of the piece so that the bolt is pulling it into the piece, not out of it.
These rivnuts are very common used in the aviation industry. Thanks for sharing 👍
Thank you 😊 Have a nice time 🍀
Too commonly used IMO.
I had a real specific need a while back, and it did not need to be real strong and I ended up using some of these in a concrete wall. I drilled a hole just slightly larger than the rivet nut, coated the outside with an epoxy, inserted and compressed. Held like a champ.
Thank you 😊 Have a nice time 🍀
I don't see why they wouldn't work in concrete, even without the epoxy.
@@ameunier41 I tried it without the epoxy at first, and after putting the screw in, it was not that hard to wiggle it out. With the epoxy, it would not budge.
Try the longer ones meant for thicker plates. Crimple zone is further down the pop nut
Thank you 👌😊 Have a nice time 🍀
I was thinking similar. And if you want to do it to thin plywood, use a washer on the back.
@@BenNawrath that's a clever idea.
You can make the bulge on the nut happen further down into the wood by wrapping wire around the shaft near the top of the nut. That way when the screw compresses the nut, it can't do it right at the top -- the wrapped wire prevents that compression there.
Здравствуйте, спасибо вам . Что в роликах идёт показ как и что и для чего , многое почерпнул для себя , кое-что не ново ,но пойдёт. У вас подача хорошая ,так держать 🤞🤞🤞 . С уважением с берега озера Балхаш
🤜🤛👍 감사합니다 😊💚😊 좋은 하루 되세요 🍀
Support 👀
Nitonakrętka była stworzona do łączenia cienkich blach za pomocą połączeń śrubowych lecz bez dostępu z jednej strony i niemożności wykonania gwintu w zbyt cienkiej blasze o wystarczającej sile na rozciąganie takiego połączenia. Można nitonakrętkę stosować do innych materiałów ale trzeba liczyć się właśnie z mniejszą trwałością związaną z mniejszą wytrzymałością danego materiału niż metale. Ja używałem nitonakrętek w tworzywach sztucznych. By nie uszkadzać tworzywa i wzmacniać mocowanie dodatkowo dodawałem metalową podkładkę, co nie zawsze jest możliwe.
dziękuję 😊 miłego dnia
Support 👀
Very nice, you could drill through the wood and use it as a blind nut. Really strong. I will have to include this in my list of Fasteners. Thank you
👌👌👍Thank you 😊 Have a nice time 🍀
Support 👀
I'm pretty sure if you drilled those holes deeper than you did it would not try pushing out while you were installing the part. If you watch it's pushing out because the bolts are bottoming out on the back side pushing the whole thing out before it can start to expand.
Support 👀
감사합니다. 당신같은 실험맨 덕분에 신문물을 접할 수 있습니다.
과찬 감사합니다. 좋은 저녁 되세요 🍀👍💚
Excelente tutorial maestro, cómo siempre unas ideas peculiares, gracias por compartir sus conocimientos y experiencias, un saludo cordial y por supuesto un gran like desde Narón (Galicia)👌🤓
👋👋💚 Gracias 🇪🇸😊 Que tengas un buen día 👍🍀👌
Support 👀
Thanks for doing this so we don't have to!
Thank you 😊 Have a nice time 🍀
Put the rivnut in from the back (if possible) and the flange will pull against it instead of pulling out the weaker expanded part.
Gracias por su trabajo, tiempo y dedicación. Muy útil y práctica la tuerca.
Gracias 😊 Que tengas un buen día 👍🍀👌
Support 👀
A modified version, with the rugged bending part moved a little bit more towards the end would be perfectly suitable for this application.
👍👌Thank you 😊 Have a nice time 🍀
That was my exact thinking. The manufacture could move the crumple zone a few mm toward the bottom of the nut and you have a fantastically stong connection.
Yup. Same thought. Since I know they don't make it that way I thought about grinding the rivet crimping spot further toward the end.
이번 영상도 기대를 저버리지 않는군요
잘보고갑니다
역시 👍
다음 영상도 기대해볼께요
감사합니다 😊👍😊 좋은 하루 되세요 🍀
Support 👀
Since rivnuts are brand specific... try a plus nut or split nut designed to flare around an inch back from the face. From experience, the nut must be matched to the material thickness.
There are threaded screw inserts which are specifically designed for soft wood 😅 Might want to look into that if you work with this a lot. I have seen a type which is self-tapping as well, so you don't need to pre-drill holes first. Good stuff👌
Thank you 😊 Have a nice time 🍀
Если винтовые вставки отсутствуют, то это будет заменой. Хотя и временной. 👍🏼
@@PavelKostolomoff Истинный
Что выдумывать проще взять специальные ввёртки с резьбой снаружи и внутри, их садят на клей и они гораздо надёжнее
실망시키는법이 없는 영상~~~🍀🍀🍀🍀🍀
감사합니다 😊👋😊💚 좋은 하루 되세요 🍀
Support 👀
Now that is cool 😎 Thanks for sharing 👍
Thank you my friend 😊 Have a nice time 🍀
Support 👀
@@squirreltech what are you going on about
Try a prebulbed style?
I often just epoxy rivnuts into wood after I've scratched a rough surface on the nut. It's good for making jigs, but if you want it to last, I always use the stainless steel EZ-Lok threaded inserts. Other threaded inserts tend to be too soft for most aspects.
You can use the rivnuts in your video for things like aluminum or steel that is on a woods surface.
You should try it with rivet nuts intended for thicker materials. It moves the “weakened” part farther from the surface. I bet it would work even better. This has me thinking how pop rivets would work!🤔
Thank you 😊 Have a nice time 🍀
나무의 종류별로
테스트에 굿~입니다. ^^
니벳너트~용도가 다양하군요
감사합니다. 목재에 실사용에는 에폭시 본드를 첨부하는 것이 좋을 듯 합니다.^^
👍👍👍Лайк в карму за креатив и полезную информацию!
Support 👀
I’m surprised it works although I wouldn’t trust it, they make wood treaded inserts for machine screws. I did like the video!😊
Thank you 👍🛠️💚😊 Have a nice time 🍀
Support 👀
При тесте на отрыв. Нужно учесть что болт упирается в древесину и вытаскивает основание. А нужно было тогда просверлить глубже отверстия под болт.
Спасибо 😊 Хорошего дня 🍀
A really useful test. Thank you.
Not something I would have thought of doing, but, yes it works, with appropriate guidelines.
Test… Great point! Thank you 😊 Have a nice time 🍀
Support 👀
Nice video. Thank you!
Thank you 💚😊 Have a nice time 🍀
Support 👀
На мой взгляд на видео очень доступно продемонстрировано, что всё таки резьбовая заклёпка не очень удачный вариант для дерева. Гораздо лучше на эту роль подходят втулки с метрической резьбой внутри и крупной резьбой для дерева снаружи.
Спасибо 😊 Хорошего дня 🍀
А ещё очевидно что кирзовые сапоги не сильно подходят для игры в футбол гораздо удобнее играть в кроссовках бутсах или кедах
Trial n error new creation. Craft Level Up. Very nice. 👏🤙
Thank you 🤜🤛😊 Have a nice time 🍀
Exelente video 😀👍gracias
Gracias 😊 Que tengas un buen día 👍🍀👌
Support 👀
بارك الله فيك وسلمت يداك 😍
شكرا 😊😊 أتمنى لك نهارا سعيدا
Amazing work ❣️
I am support your Chanel ❤️
Have a great day 😊
🙏💚😊 Have a nice time 🍀
I absolutely love riv-nuts. It's niche thing but once you have a tool and bag of them, you find uses.
👌👍 Thank you 😊 Have a nice time 🍀
Good test. I'll stick to threaded inserts
Thank you 👍😊 Have a nice time 🍀
A washer on the back for the thin ply?
Good idea 👍
Like19,.,.,.
영상 잘 봤습니다!! 또 오겠습니다!!
감사합니다. 감기 조심하시고 멋진 주말되세요 💚😊
Put a few drops of oil on the thrust washer and bolt threads, it will go easier and last a lot longer
Washer… 👍👍👍 Thank you 😊 Have a nice time 🍀
Support 👀
목공에 관심있는 일인입니다
너트 만드는 회사에 건의를 하면 안될까요?
주름 부분을 머리에 바짝 붙여서 하지말고 목공용으로 중간쯤에 주름을 만들어 달라고. 그러면 완전 목공용으로 쓸 수 있을 듯합니다~~♡♡
네~ 저도 그런 생각을 했습미다. ^^ 감사합니다 😊😊 좋은 하루 되세요 🍀
Increíble, acabé en la cama con mi señora 😂🤣😂🤣😂🤣😂🤣💃🦸♂️🦸♂️💃💃🦸♂️🦸♂️👍🏻
여러 작업에 사용될 부품 같네요. 저도 언젠가 마음껏 사용해볼 날이 오기를 😊
네~ 목재 사용 시에는 에폭시 본드를 바르면 효과는 확실할 것 같습니다. 감사합니다 😊😊 좋은 주말 되세요 🍀
멋진 아이디어! 감사합니다 ^^
저도 감사합니다. 좋은 하루되세요 😊🍀👍
👀
Support 👀
목공용으로는 애매하다는 생각이 드는군요. 한번 세게 쪼이면 터저버리니..
참고되는 좋은 영상입니다
감사합니다 😊😊 좋은 하루 되세요 🍀
Rivnuts plus a dab of epoxy would be very solid.
This is wood expansion anchors. The same as in concrete - KB-TZ2 and many other manufactured by HILTI and Simpson.
So what you're saying is if you must use in wood first drill plenty of relief behind it second don't tighten it all the way down and third never use for anything structural... got it thanks, very informative
Thank you 👍👌👌😊 Have a nice time 🍀
شرح عملى مبسط ورائع 💪👍
شكرا 😊💚😊 أتمنى لك نهارا سعيدا
Ist doch selbstverständlich, daß die Niete nicht halten kann, wenn das ins Holz gebohrte Loch kürzer ist als die Schraube, die man anschließend in die Niete schrauben will!
If you use these a lot I would recommend lubricating the compression bolt. It will make it last much longer.
Thank you 👌😊 Have a nice time 🍀
Buenos días.
Buen video.
Sería posible saber donde adquirió el útil para las tuercas ?.
Muchas gracias
Lo compré en Corea, pero creo que también podría venderse en Amazon. búsqueda de costillas. Gracias 😊 Que tengas un buen día 👍🍀👌
Rebite na madeira também seria a mesma coisa?
E se colocasse uma arruela em cada lado, será que funciona?
Sí, los mismos remaches en madera. También puedes poner arandelas en ambos lados. Aún mejor, si le pones rodamientos. Gracias 😊 Que tengas un buen día 👍🍀👌
Slt c est une excellente découverte j avais pas pensé à cette méthode, car il existe des chevilles pour le bois mais !!! Et sa a l'air de bien fonctionner p 👍👍👍👍
Merci. 💚 passe une bonne journée 😄🍀
Спасибо за информацию!
🤜🤛🍀
Vc poderia fazer o furo para sair do outro lado e prender o parafuso pelo outro lado assim a resistência seria muito maior. pois exerceria a função de aperto muito melhor.
🍀👍💚
Concordo com a sua lógica, mas pergunto: qual a vantagem de usar isso no lugar de uma porca com arruela?
What about just under sizing the hole and threading directly into the hard wood?
👌Yes, it is… 😊 Have a nice time 🍀
Great idea, but not sure if it’s better than using threaded inserts. Any thoughts, anyone?
Thank you 👌😊 Have a nice time 🍀
Hay quá! Cám ơn đã chia sẻ
cảm ơn. 😄 Chúc một ngày tốt lành 🍀
좋네요! 리벳너트 처음 알았어요
감사합니다 😊💚👌👋😊 좋은 하루 되세요 🍀
О
우그러지는 부분이 중간쯤에 있는 제품이 있으면 목제용으로 좋을 것 같단 생각이...
네 저도 같은 생각입니다~~👍🤜🤛🍀
Try torquing them down to expand but not all the way they rip the wood away to nothing
Thank you 😊 Have a nice time 🍀
Как всегда здОрово 👍👍👍🥰🇷🇺
Спасибо costa mac 🇷🇺😊 Хорошего дня 🍀
excellent👍
Thank you 😊 Have a nice time 🍀
좋은 생각이네요 라고 하며 보면서 드는 생각이 목재전용으로 저 주름 부위가 끝이 아닌 중간쯤 있는 것이라면 다양한 목재에충분히 활용하겠다 싶어지네요.
네~ 맞습니다. 활용하려면 강력한 접착제를 먼저 넣은 후 조이면 괜찮을 듯 합니다. 🍀😊🛠️
For hardwoods you can use a tap & die. No ongoing cost of RivNuts
👌😊💚
Support 👀
목재용으로 쓰면 안되는거라 안쓰겠지만 궁금하긴 했습니다. 실험 감사합니다.
감사합니다 😊😊 좋은 하루 되세요 🍀
Sobre madera. Con un arandela de cada lados. Queda muy firme..
Gracias 😊 Que tengas un buen día 👍🍀👌
you should try a plus nut for deeper holes
Thank you 😊 Have a nice time 🍀
목재나 프라스틱용 너트리벳이 따로있음
Круто мы все поняли без слов 😂👍спс за труд.
Support 👀
@@squirreltech у меня нет перевода 😂
Muito bom valeu muito obrigado!!!.
Obrigado 😊😊 Tenha um bom dia 🍀
I use this nuts with super glue, little bit less hole put glue and press nut with hummer.
Where possible the nutsert can be installed behind , with a thro hole in the wood to fasten from the opposite end. Will be more robust.
👌Thank you 😊 Have a nice time 🍀
А есть же специальные для дерева с шариком внутри
Es la primer vez q lo veo, lamentablemente acá en Bogotá, Colombia no lo importan. Así como otros tipos de tuercas las armado entre paneles, módulos, bases etc.
Gracias 😊 Que tengas un buen día 👍🍀👌
They would be great in hand wood.
Manufacturer needs to make some for wood alone. Wrinkle deeper
Thank you 😊 Have a nice time 🍀
I like..
Thank you 😊 Have a nice time 🍀
1 giả lập tuyệt vời 👍👍
cảm ơn. 😄 Chúc một ngày tốt lành 🍀
음 잘 뽑히지 않는거 같아서 신중히 사용해야 겠네요!!
네 한번 체결 후에는 착탈은 포기해야 될 거 같습니다. 감사합니다 😊😊 좋은 하루 되세요 🍀
Под дерево нужны другие заклепочные гайки - чтоб насечки предназначенные для деформации были расположены как можно дальше от прессшайбы, может даже в два ряда - если Вы хотите использовать эту технологию для дерева.
감사합니다 😊😊 좋은 하루 되세요 🍀
Para resolver el problema en la madera, tan sencillo como poner una arandela para que la presión la absorba ésta y no se hunda. Así lo hago y me funcilna a la perfección.
Gracias 😊 Que tengas un buen día 👍🍀👌
Support 👀
Muito bom.
Obrigado 😊🛠️🍀😊 Tenha um bom dia 🍀
Support 👀
Мне понравилось.
감사합니다 😊😊 좋은 하루 되세요 🍀
Needed different rivet
those are not rivets ,,, they are rivinuts ,,, totally different thing.
Why this hemorrhoids? There are also special furniture threaded bushings
Just use threaded inserts.
Thank you 😊 Have a nice time 🍀
Show de informação !!!!!!
Obrigado 😊😊 Tenha um bom dia 🍀
Support 👀
Зачем такие гайки в древесине для этого мебельные забивные давно изобрели
Guarda che esistono già le bussole in zamak o ottone da applicare nel legno con la filettatura interna metrica.
Obrigado 😊😊 Tenha um bom dia 🍀
What is Rubber wood?
If you google it, you can see the picture.Thank you 😊 Have a nice time 🍀
👍👍👍👍
👍😊💚🛠️
Excelente ideia . Brasil -> #ForaBolsoNazis
Obrigado 😊😊 Tenha um bom dia 🍀
Эти заклёпки для метала а не по дереву по дереву есть специальные заклёпки
Thank you 😊 Have a nice time 🍀
안녕하세요. 검은별님
이런 방식으로 목재에 쓰는 너트 중
혹시 목재피스에 맞는 직경의 너트는 뭐라고 부르나요? 꼭 알고 싶습니다..
안녕하세요… 이해를 잘 못 했어요. ㅜㅜ
혹시 번데기 너트를 말씀하시는 건지요? 그려서 주실 수 있음 시간나실 때 메일로 주세요.
Прям капитан-очевидность...
Onde comprar???
Comprei na Coréia, mas acho que provavelmente será vendido na Amazon também. Pesquisar por rivnut
Что за бред. Для дерева саморезы есть.
Показывать надо на липе, ели и ольхе, а на дубе и так понятно.
8mm로 테스트 하신거죠?
네 맞습니다~~^^