Always nice to see a newly built quad fly, but you've used pretty ancient hardware. For your next build look into BLHeli_S or BLHeli32 ESCs and quadcopter-specific motors with threaded shafts.
i'M USING arduino mega 2560. Reciever is not talking to arduino and the stick movements doesnt work like as in your video on the accelerometer calibration software.. any ideas?
I enjoyed every one of these 6 minutes video!!! This is it!! Grab a few things and build something from scratch!!!! Well done and enjoy your work!!!!!! Well done!!!
@Sulayman Guelleh i counted up towards over 50 bucks but that was not inclued the controller which also was linked to in the video description and it was like $85 and the "ESC" in the list was not found on aliexpress at least on that link
It really shouldn't be a problem, just tighten them down. If you are worried, you can use some blue thread locker which holds the nut in place until you use a tool to loosen the nut, or you can invest in some nylon lock nuts, which is what people use on 100mph + race quads
Yes i faced this problem with same type of motor.... My quad fall from 20 feet height...... Because the propeller adapter comes out from the motor shaft....... And 2 motors of my quad get damaged including 3 props....
Hello! Loving your project! trying to build a Quadcopter like yours but using carbon fiber tubes. Anyways I can get the code ad schematics you used for the Arduino Uno Quad Copter, or the nano, whichever one you recommend most, I got both. Thank you!!! I tried your link but it did not work.
It'd also be awesome if you post the links to all the items needed in this project is saw the flight controller and it was awesome it had all the links and details so please post all that.
can somebody please tell me which is the front of the drone an which one is ESC1, ESC2, ESC3 and ESC4 on the drone? i'm confused with this things because the gyro is inverted in proportion with propeller direction and motor???????????????
is it necessary to connect receiver and ESC to flight controller when it connect to multiwii? without ESC and receiver, when I click start then the multiwii window is closed. what is the problem. i need urgent help
You don't need to keep the ESC or receiver connected while using the multiwii software, Make sure that you remove the Bluetooth Module and run the Multiwii GUI in Compatibility Mode.
Okay thanks, and in the multiwii arduino code there is a code for GPS so can I add GPS to it if so can someone please post schematic for that. And also it'd be cool if there was a barometer for altitude hold function.
vishal sharma You can do it with kk2. 1.5 but you can do it with arduino but for that you need code of arduino. There are many open source code like Multiwi. You can try this.
Why don't you use some F3 or F4 board instead of kk2.1.5? I mean kk wasn't bad board in the past, I had ton of fun with it, but now you have better options.
Hey man I checked the website and there's a lot of great stuff in there but regarding the schematics, circuit diagram or pin diagram there's no such thing, there's one link that says connections but whenot clicked it leads to a page not found message so please post all the schematics including GPS, sonar,gyro....
Use and recommend Hardware module. Use the following Image for connections on your arduino as reference www.google.co.in/search?q=multiwii+gps+connections+pin&rlz=1C1JZAP_enIN746IN746&tbm=isch&source=iu&ictx=1&fir=mV0IPB4Y51tpIM%253A%252Cv_0R1pR8FhMtRM%252C_&usg=AFrqEze3h_0xDKEtQPBGv4eOUbXo3dnIyQ&sa=X&ved=2ahUKEwi61azu0u7cAhXIeX0KHUSGC8oQ9QEwAXoECAMQBg#imgrc=mV0IPB4Y51tpIM:
yoshiaki yo No Need to program Brushless motors can spin both directions, Just change the 2 of 3 wires (don't touch the middle one) on the esc/motor connection.
Sir i want to ask you that what is the length of the aluminium structure and the length of propeller,kv of motor,mah of battery and how can we connect camera gps and barometer please answer me sir I'm making a college project in which it is needed very much if anybody knows just ans it...
Always nice to see a newly built quad fly, but you've used pretty ancient hardware. For your next build look into BLHeli_S or BLHeli32 ESCs and quadcopter-specific motors with threaded shafts.
Thanks for the video! Wanna do the same, but unfortunately your schematics are unavailable, could you please fix the link or send a new one?
Yes, the same, i'd really like to look at the schematics
Nobody works for free
The code looks really big, very well organizated tough, good job! :D
can i have that code..., seems the link is broken...
can i have code and schematic from yours
could you please publish the code? the original repository is gone :-( thanks!
i'M USING arduino mega 2560. Reciever is not talking to arduino and the stick movements doesnt work like as in your video on the accelerometer calibration software.. any ideas?
SIR your project is nice and very simple good job
I enjoyed every one of these 6 minutes video!!! This is it!! Grab a few things and build something from scratch!!!! Well done and enjoy your work!!!!!! Well done!!!
That is pretty neat.
Really great!Nice project
Is multiwii drone stable
Means it doesn't crash during flight I high winds ?
If i would like to use brushed motor insted og brushless motor then arduino code will be same or different? and what will be the conection diagram.
And the total cost ?
yes total cost please :)
around 100-150$. The main component here wich is the most expensive is the radio receiver and the radio transmiter( the remote).
@Sulayman Guelleh i counted up towards over 50 bucks but that was not inclued the controller which also was linked to in the video description and it was like $85 and the "ESC" in the list was not found on aliexpress at least on that link
Bro during programming setup One stick is
assigned to two functions
How to solve this problem
Did you use counterclockwise propeller adapters?
If yes, where did you find them?
If no, have you ever lost propellers in flight because of this?
It really shouldn't be a problem, just tighten them down. If you are worried, you can use some blue thread locker which holds the nut in place until you use a tool to loosen the nut, or you can invest in some nylon lock nuts, which is what people use on 100mph + race quads
aap cycle duka pe jao woha par nut mi jayega me vi use kar raha hu
Yes i faced this problem with same type of motor.... My quad fall from 20 feet height...... Because the propeller adapter comes out from the motor shaft....... And 2 motors of my quad get damaged including 3 props....
Does it drift?
Can you please gave a full source cade description link is not working please reply..
Hi there link doesnt work so could you please let me have the code and the schematic
Hello! Loving your project! trying to build a Quadcopter like yours but using carbon fiber tubes. Anyways I can get the code ad schematics you used for the Arduino Uno Quad Copter, or the nano, whichever one you recommend most, I got both. Thank you!!! I tried your link but it did not work.
soooo cool as always
very nice project!!
nice project really appretiable.👍👍👍
Awesome video!!!!
Could you please give us the code? I am very interested in reproducing your project. Thanks
Is it possible to controll it With the Phone instead of rc controller
It'd also be awesome if you post the links to all the items needed in this project is saw the flight controller and it was awesome it had all the links and details so please post all that.
no updates on the project? are you using the drone anything? sold it?
Nice, what was the final weight? with no cameras attached?
good one, keep it coming
Can i use 3s 1000mah lipo battery
What if we control the quadcopter with Bluetooth via mobile , is it necessary to purchase the transmitter?
heck yeah flies good
the code link is broken. can you share again?
How much weight it can lift
can i use the same schematics without the receiver parts
You better place the sensor in the middle.
can somebody please tell me which is the front of the drone an which one is ESC1, ESC2, ESC3 and ESC4 on the drone?
i'm confused with this things because the gyro is inverted in proportion with propeller direction and motor???????????????
I cant open the website for the code and schematics
where is the code and diagram?
do we have to make the flight controller or it is available in markets
Check on flyrobo.in
How long does that 2200mah battery last for while flying?
Link code and schematic not found
is it necessary to connect receiver and ESC to flight controller when it connect to multiwii?
without ESC and receiver, when I click start then the multiwii window is closed. what is the problem. i need urgent help
You don't need to keep the ESC or receiver connected while using the multiwii software, Make sure that you remove the Bluetooth Module and run the Multiwii GUI in Compatibility Mode.
RZtronics when I click start button on multiwii then the multiwii window is closed. what is the problem...
Very nice! What's the weight of the frame? what is the flight time with one charge? Many thanks in advance
Please send me a copy of the code because I could not get it.
Great project but why muliwii and arduino when you can use betaflight or iNav and cheap F4 flight controller?
Can you make a heavy lifting one on 6 s ?
Can u give connections(schematic diagram) for brushed motors.
i want to Code and Schematics
please share code, thank you
is that vinyl of any structural support? or just for fun??
its carbon fiber dude. pimp my drone
where i can find the full code
excellent projet
Code and semantics link is not working
Okay thanks, and in the multiwii arduino code there is a code for GPS so can I add GPS to it if so can someone please post schematic for that. And also it'd be cool if there was a barometer for altitude hold function.
Yes, You can add GPS, Barometer, Sonar and many other this in Multiwii. check it ut here-www.multiwii.com/wiki/index.php?title=Main_Page
arduino code not abailable
Bluetooth module?? Was it for short range to control it? Am I?
And may I know about the code or syntax for arduino nano...
Gates Alfareno Transmitter and Receiver for best range. Receiver to arduino for ppm/pwm signals
And what's the length of all four aluminium bars?
Code and Schematics Why not
Please make gps, barometer, quadcopter
Ranjit Kumar iughhu
GPS + gimbal with 4k camera
vishal sharma
You can do it with kk2. 1.5 but you can do it with arduino but for that you need code of arduino. There are many open source code like Multiwi. You can try this.
Why don't you use some F3 or F4 board instead of kk2.1.5? I mean kk wasn't bad board in the past, I had ton of fun with it, but now you have better options.
Multiwii Error - minidumps are not enabled by default
Help please
Hey how can I get full source code to build this project? The link in description is not working. Please reply it will be helpful
Did u get it help a homie out
Bluetooth module can control drone its Right
Thanks I'll check it out.
You did not face any type of noise due to vibrations
Can you please Tell me the length of sticks ?????
Hey man I checked the website and there's a lot of great stuff in there but regarding the schematics, circuit diagram or pin diagram there's no such thing, there's one link that says connections but whenot clicked it leads to a page not found message so please post all the schematics including GPS, sonar,gyro....
For more information on additional features like GPS visit-www.multiwii.com/wiki/index.php?title=Main_Page
Use and recommend Hardware module. Use the following Image for connections on your arduino as reference www.google.co.in/search?q=multiwii+gps+connections+pin&rlz=1C1JZAP_enIN746IN746&tbm=isch&source=iu&ictx=1&fir=mV0IPB4Y51tpIM%253A%252Cv_0R1pR8FhMtRM%252C_&usg=AFrqEze3h_0xDKEtQPBGv4eOUbXo3dnIyQ&sa=X&ved=2ahUKEwi61azu0u7cAhXIeX0KHUSGC8oQ9QEwAXoECAMQBg#imgrc=mV0IPB4Y51tpIM:
Code and Schematics is dead link........ (ToT)I need a program source.
how to flash xxd 30A esc with arduino please bro help me my esc not working properly!!!!!
what is the dimension of frame??, plz include it
how much can it carry?
Where can i find the code and diagram.. plzz help..
sir? and the totals cost?
Can you tell the battery capacity and all the details including voltage....
2200mah 3s(12v) Lipo
how much is the total cost sir?
sir please share the link for code
If you haven't yet, you should really get a 3d printer
What about the remote control?
Pls how can I name a remote control for my drone ....
can we program brushless motors in two directions? how
yoshiaki yo No Need to program Brushless motors can spin both directions, Just change the 2 of 3 wires (don't touch the middle one) on the esc/motor connection.
You has already maxe this no difference is there please use other fitures lile gps. Altitude hold, sonar, etc so it will more good. Use multiwii
Nice bro
Sir i want to ask you that what is the length of the aluminium structure and the length of propeller,kv of motor,mah of battery and how can we connect camera gps and barometer please answer me sir I'm making a college project in which it is needed very much if anybody knows just ans it...
10 i believe (Propeller)
Cuircuit diagram pls
HI... how can I have a contact wih you?
Sir all rod are equal
And please post the dimensions of the aluminium body.
you can have dimensions as per your requirement.
it's amazing
your web site (rztronics.com/arduino-flight-controller-for-your-quadcopter/) is not showing the pictures
what's the of programe do u use in make your videos
المخترع Inventor Multiwii
Adobe Premiere Pro
Amazing :)
Welp I be able to finish this and it worked :D welp it took me like 20 hour total because I’m not really good at building stuff. But worth it!
Hey do you have the code and diagram of this project?? Plz help
code?
Those steel L's add some weight.
Sir please provide us the measurement of your frame plz sir i m very confused regarding this sir...
2212 motor with 20a esc ???
This esc will blew up when u fly !!
How to fix this ?
Laurens Van Der Meiren change to another esc
@@laurensvandermeiren1678 USE 30A ESC
Give the codes
You can't explain it
Code for that
Video description?
Kitna rupye Lagege Bhai
Code ploki
reel