Thanks so much for the quick tutorial, it was really helpful in getting this quad newb setup quickly, especially the modes. Was wondering if you experienced anything like this before. I did all my settings in the VTX section, channel, power output etc. then saved. A little later I went back and wanted to double check those settings and now it says it doesnt recognize any VTX on this unit. Signal appears to be fine on my VTX goggles so I assume the VTX is working it just doesnt see it in Betaflight, also in the OSD menu it doesnt recognize either. Have you seen anything like this before ?
There was no need to remove the prop guard... u can plug in the usb by removing the black cover on the nose (above the cam, below the action cam mount).... great vid tho!
@@iFLYXWings6589 I see now. You disconnected from the drone and reconnected to your internet wifi. I was still connected to the drone since you didn't mention that you switched. Anyway, I think I have it working now. Thanks!
Greetings, if I wanted to change the antenna for a lollipop, could you help me with the size? There are many measures and I don't know which one is appropriate.
Assume you are talking about ELRS. 1. Make sure the firmware matches. Either both on 2.X or 3.X 2. You can bind using the bind button on the FC and clicking bind at your radio
I have same Darwin Cineape elrs with Betafpv transmitter. It’s been few months that I am trying to bind but been unsuccessful. I am new to this and in need of help. Would you please help me ? If possible please share your email and I will reach out there. Thanks!
You got a new sub.Well done!
Thanks 🙏
HI , to connect to BATA there is no need to disassemble the drone, the USB C is above the camera, you have to remove the black rubber
Yes, thanks for clarifying. I did made a separate video to explain this mistake I made
yes there isn't even an instruction leaflet, you have to invent everything@@iFLYXWings6589
Thanks so much for the quick tutorial, it was really helpful in getting this quad newb setup quickly, especially the modes. Was wondering if you experienced anything like this before. I did all my settings in the VTX section, channel, power output etc. then saved. A little later I went back and wanted to double check those settings and now it says it doesnt recognize any VTX on this unit. Signal appears to be fine on my VTX goggles so I assume the VTX is working it just doesnt see it in Betaflight, also in the OSD menu it doesnt recognize either. Have you seen anything like this before ?
Nevermind I figured it out. I accidently disconnected my VTX tramp setting from UART 2. Now its all showing again, thanks again for the great vid
That will be by answer to you as well, glad you figured it out
There was no need to remove the prop guard... u can plug in the usb by removing the black cover on the nose (above the cam, below the action cam mount).... great vid tho!
Thanks 🙏 found out after this video is released andI later released a video to clarify this
Mine is not working :( it’s usb-c and befit cannot recognize it through this port
Buen tutorial, pero la.conexion a la fc esta arriba de la camara, sin tener que abrir el drone
Thanks 🙏 I noticed right after I released the video
By the way, you don't need to flash your binding phrase, from 3.x you can just input it on the web ui :-)
followed it all perfectly, no luck.
Does the Cineape 25 have a beeper? Iv'e got mine setup in betaflight and the switches but no beeping.
Nothing shows up for me under target once connected to wifi in the ELRS configurator. What gives?
Nothing will show up in the ELRS configurator, what you want is the pop out web page
@@iFLYXWings6589 I see now. You disconnected from the drone and reconnected to your internet wifi. I was still connected to the drone since you didn't mention that you switched. Anyway, I think I have it working now. Thanks!
My new radio master tx12 wont be connect to WIFI , any help please !
Same, try on offing your WiFi at PC
Hello ! I bought This drone, but 6s iflight 4000mah battery, do you think it Will work? The battery seems to heavy
No this is a 4S drone, putting 6s may potentially fried your board. The capacity range for this one should be 450mah to 1000mah
@@iFLYXWings6589 mine is the 6s version, but yet it seems to be a big battery
Hi beginner here, Can I use my Radiomaster pocket with this kind of setup?
Yes, you can
Greetings, if I wanted to change the antenna for a lollipop, could you help me with the size? There are many measures and I don't know which one is appropriate.
I will be trying this and will be releasing a video for it, stay tuned !
I fly stickmode 3 on drones. Is this possible with this drone?
Yes, you just need to adjust your stick channel mapping in BF
@iFLYXWings6589 and i guess replugging the motors in the other channels?
@@jasmijnariel The assumption is you do not need to do that if you change your channel mapping correctly.
Can you help? I have jumper t-pro v2 and betafpv cetus x how i can bind ?
Assume you are talking about ELRS.
1. Make sure the firmware matches. Either both on 2.X or 3.X
2. You can bind using the bind button on the FC and clicking bind at your radio
If use a 650mah Tattu battery, how many minutes can you fly?
You should be able to expect 4-5 min by default
hmm, isn't there a USB above the camera? pull out the black plug😊
😂you are correct, I thought it was a beeper for some reason
Just made a short to clarify this and added time cards and in the description, thanks again for watching my back!! : )
I have same Darwin Cineape elrs with Betafpv transmitter. It’s been few months that I am trying to bind but been unsuccessful. I am new to this and in need of help. Would you please help me ? If possible please share your email and I will reach out there. Thanks!
If you are using the BetaFPV Transmitter(white gamestyle one) that one only supports ELRS 2.0 you will need to downgrade your Cineape to ELRS 2.0