The water fills in through the side holes for the skewer. You can avoid this by adding short plastic tubes (isolated with glue) to the holes just a little wider than the skewer and stuffing some vaseline inside. The skewer will still turn but vaseline will add insulation. Tried it, works great.
Put the bottom cross braces inside for less resistance to forward movement.the holes for the axle are your leaks . grease an additional skewer and install it temporarily. Use your glue gun to create bushings for the axle. Spin gently while cooling off. Install paddle wheel. It might not be perfect, but probably better than none.
for more speed... cut down your original paddles... and use the off cuts glued on at 90 degrees to the smaller paddles.... less drag, faster paddle speed with a larger surface area as well as setting the paddles at different angles to each other.... so that you get a smoother operation... as you only have four blades on each side ... otherwise boat is amazing :) well done
Just watching this guy making it is satisfying. But being able to make it is immensely fulfilling. Edit: using more than enough strengthening and too much glue might increase the weight, so maybe we can try to minimise all of it.
I think maybe it’s the weight of the paddles weighing it down at the back enough to take on water over the sides. Maybe if the paddles were closer to the middle it would ease the issue. Also maybe if you could find something to fill the bottle caps with that was lighter than glue gun glue, which is quite heavy in a lump like that. Air dry foam clay might work as the right kind can be very light. Maybe use a small amount of glue to stick the wood together and then fill around it in the bottle caps with the clay to reinforce it.
Great video. I made one with my 8 year old boy for a school project. Didn't bother with the rotors. Just a boat and put a wee sail on it. However after putting it in water it all fell apart I used a glue gun and craft sticks bought from Amazon. The problem seemed to be the carft sticks all buckled and bowed and weren't water resistant. So something to look out for if you plan to build one.
I believe if you were to misalign the paddles at a 45° angle it would make it go faster/farther making it more efficient. With all do respect there is nothing wrong with what you made, I'm looking at it as if it's a boat made by a toy company not a project that anyone could do.
I was about to say when you put the bottom together that you should glue between them as well... but you learned that lesson later I see lol.... You could've raise the sides true, or drilled the holes a cm more towards the center... in any case a child would love it, especially if grandma/grandpa/mom/dad and him/her each made one.
Super cool. I'm going to make one with my nephew. I might try out using the old wooden ship keel and skeleton with molded planks method. I wonder if I steam the craft sticks if I can get them to hold the shape I need. Be interesting. Thanks for the vid
Is this a wind-up?
DaveHax yes
Hi
Love you
yes I love it
Yeah, you're the best! 😉
Been watching this guy for years now
Old is Gold ⭐
·LiSoo : Army· same
Old And Gold Both Rhyme
_Old
Gold
See the similarities?
Watch this also i thing it's also interesting for you
ruclips.net/video/l3DN-0OpY6M/видео.html
@@ARABIANGROUPGYPSUMCTR I subbed to your cqhnnel
I love you
This is a great demonstration of conversion of elastic potential energy to kinetic energy
The water fills in through the side holes for the skewer. You can avoid this by adding short plastic tubes (isolated with glue) to the holes just a little wider than the skewer and stuffing some vaseline inside. The skewer will still turn but vaseline will add insulation. Tried it, works great.
The music, his accent, and the occasional “pretty cool huh?” will never get old.
Yes
good
8:31
Hmmm
So true
Do you come up with these yourself? They are very creative!
Or you could say it's *Pretty Cool Huh?*
*Not Again*
Diamond Block HOORAY! IMA MINE YOU
Oh no.....
BEANS McCHEESE No... I will!
💎⛏
Cool idea . U can glue the band to the stick ,in that way it doesn't get ditched from stick after a complete spin.
Wow i am going to do thisnow for my school project
A wonderful idea 😀😀
How many Y’all are watching this knowing you will probably never do this but silently wish you could?
cringey piece of garbage
Umm that’s actually really offensive dude ( PS I don't know how this is offensive. Me after a month)
me
Me
Haha
bottle cap: Please Recycle me
Davehax: y’know a boat kinda sounds more cool-
bottle cap: *please*
Hrnng I wish I was Dave's bottle cap right now
Buy Coca cola
Lol bruh
Cameron G that would be a bit painful
Put the bottom cross braces inside for less resistance to forward movement.the holes for the axle are your leaks . grease an additional skewer and install it temporarily. Use your glue gun to create bushings for the axle. Spin gently while cooling off. Install paddle wheel. It might not be perfect, but probably better than none.
Its way better to make the axle a little bit higher, its at the water level, thats why the water gets into the boat.
i could listen forever to that sweet piano music he always has in the background
Thanks Dave, for strengthening our collective inner child with original fun builds!
Very important in this cyber day and age! Cheers!
ওকে
50
50 না কেন
1ঐট8পচপঝজৈঘ ধচপধচধ0000
এসছে ঝেদৈঈধঝঝদধচতঢজৈচজৈ133
Excelentes trabajo se los haré a mis nietitos de monterrey México!!
It looks much better than the last paddle boat you made
I forgot about DaveHax! This guy was soo cool to me when I first watched one of his videos
Edit: To this day, I still don't know what BlueTac is
its sticky tak, the stuff you use to like put up posters or something.
@@soysaucesquared906 Cool
Teachers use it to hang number lines n stuff
I have this wierd feeling you've already made this 😃
I made this boat, it's absolutely awesome
Imagine making a bigger one of those
Oh god lol that will be insane
Try putting a slice of cork under the rear part of boat.
This is the only channel I can think of where I don't roll my eyes when the glue gun gets pulled out.
DFYDGHFFJUGGKTFGJTFGHRGJYTHNJYHJJUUHUHUUUIJJJJJJJJJJJJJJJJJKKKKKKKKKKKLLLLLLLLLLLLLLLLLLMMMMMMMNNNNNBBBBVVVVVCCCCCXXXXXXX
@@umasutar4500 r/ihadastroke
Love it
What do you mean by *don't roll my eye when pulling the glue gun* ???
@@mariaramel6407 They don't have a glue gun I presume, so they're disappointed.
If you think about it Dave is just 5 minute craft but with good hacks and gadgets
for more speed... cut down your original paddles... and use the off cuts glued on at 90 degrees to the smaller paddles.... less drag, faster paddle speed with a larger surface area as well as setting the paddles at different angles to each other.... so that you get a smoother operation... as you only have four blades on each side ... otherwise boat is amazing :) well done
One of the few channels that haven't changed at all!
YOU HAVE VERY CREATIVE MIND.LOVE YOUR BOAT.I WILL TRY THIS.
you forgot to tell us to use hot glue to avoid the boat from sinking 9:16
This is so cool, you're very creative sir! Love this so much! 😉
Right.
You could say it's pretty cool huh?
Today we did this for our 3.5 yo son, so happy he is to make something which can move without an engine :-)
Sencillo, limpio y funcional, muy bueno.
Just watching this guy making it is satisfying. But being able to make it is immensely fulfilling.
Edit: using more than enough strengthening and too much glue might increase the weight, so maybe we can try to minimise all of it.
i watch Dave's videos to hear him say "pretty cool, huh?"
Same bro
Wow we tried this and it was awesome!
Thankyou!
Really handy , needed it for a school project.
To stop water from getting in you can hot glue an even layer of foil onto it! I think... unless the back is still too heavy.
Ah, the good old days of balsa wood airplanes!👍
I think maybe it’s the weight of the paddles weighing it down at the back enough to take on water over the sides. Maybe if the paddles were closer to the middle it would ease the issue.
Also maybe if you could find something to fill the bottle caps with that was lighter than glue gun glue, which is quite heavy in a lump like that. Air dry foam clay might work as the right kind can be very light. Maybe use a small amount of glue to stick the wood together and then fill around it in the bottle caps with the clay to reinforce it.
Maybe the holes where the stick is are a factor as well?
Always wanted to do that! Yup, that's pretty cool!
Great video. I made one with my 8 year old boy for a school project. Didn't bother with the rotors. Just a boat and put a wee sail on it. However after putting it in water it all fell apart
I used a glue gun and craft sticks bought from Amazon. The problem seemed to be the carft sticks all buckled and bowed and weren't water resistant. So something to look out for if you plan to build one.
Tape the bottom, tape is water resistant. Put the tape under the boat. And maybe add some in the sides. Hope this helps!
Very good idea, no tiene el problema de las hélices que pueden atascarse en aguas sucias . Estaría bueno hacerlo electrico .
Dave Hax never fails to amaze us
Watching your videos is never boring
I believe if you were to misalign the paddles at a 45° angle it would make it go faster/farther making it more efficient. With all do respect there is nothing wrong with what you made, I'm looking at it as if it's a boat made by a toy company not a project that anyone could do.
Yes! Thank you! Very helpful!
Who remembers back when Dave made a pop-pop boat using a candle, milk carton and soda can
Very inspiring, thank you for sharing👍😍
The boat looks good 💯 but I will do it in my way to make it easy 😊
Thanks Sir ! Beautiful, creative art idea !
I was about to say when you put the bottom together that you should glue between them as well... but you learned that lesson later I see lol.... You could've raise the sides true, or drilled the holes a cm more towards the center... in any case a child would love it, especially if grandma/grandpa/mom/dad and him/her each made one.
Dave how do you come up with these awesome ideas!
yay a new video but u could add some weight to the front of it so its pefectly balanced and wouldnt take in water
Dont know why im saying this buy your videos bring me so much joy hahaha.❤
Nice job
this is a very good project for kids . i made this and put it in the pool and went under water with a gopro to film it moving.
Love it❤
thank you for saying stay safe I'm so happy to say that but stay safe =3
Super cool. I'm going to make one with my nephew. I might try out using the old wooden ship keel and skeleton with molded planks method. I wonder if I steam the craft sticks if I can get them to hold the shape I need. Be interesting. Thanks for the vid
my favorite is the boat itself and the other one that you made in a different video😊
Love this video I can’t wait in till the next craft video
Wow!u awesome!!hi all from a small youtuber!wish u all a great positive day!🦄💜👻
Thanks very much, you too...
DaveHax 🙏congratulation for your work!
Amazing diy idea !!
I never realized that sanding wuuud may it loook smmart smart 🤓 I love it 🤣
Pin Dave ;) I love how creative you are!!! I love your videos so much Dave keep them up!
I have never once been let down by a video form davehax
Dave your really creative i love your videos keep up the good work and anyway you can make a diy cable tidy setup thing
Daveaxe you are my favourite DIY channel your channel is the only channel that says words you are the best!!!😀😄😄😄😀😀😁😁
It was really useful
Thanks !
Dave your waaaaaaaaaaaay better than 5min crafts keep up the good work 👍👍👍👍👍👍👌
*the caps: please recycle me, *dave: indeed i will
I w i l l
Wow 🤩🤩🤩 very beautiful😍😍✨✨✨❤❤❤❤❤😍✨
yes, this is awesome
Usted es lo máximo 👍
Did anybody notice that the boat was blue last year? Now it's red
this is a brilliant idea mate 👍
Yea this is brilpiant
Brilliant
When I saw this I remembered that I got a F in science so guess who’s getting a A in here
Very poor
@@laxmisingh7609?
@@laxmisingh7609 WDYM POOR
I think the paddles should have been place closer to the centre, so it wouldn't sink down lower than the top of the boat ⛵
If u wouldn't line up the panels the boat would do a zigzag in the water
Ye chis to main "Taree Jameen Par" Par pehli bar dekha tha 😃
Wow really nice I love it but can I have a shout out?😊
Hi! Thanks for the message!
@@DaveHax np I've been watching your vids for 3 years😊
Great boat!
But I think the paddles are filling the boat up with water
Me: makes boat
Also me: places boat upside down
Boat: *you spin me right round baby right round like a record baby right round round round*
When you found this 2 years ago on another account, but never able to make it in 2 years, meanwhile he did it in a day
next time you can make a wooden titanic breakable sinking ship?
Блин, мы такие кораблики на резиновом ходу делали ещё в 1978 году.
I tried making this a million times but I couldn't because I'm super dumb
Bestest boat of the world
U should make a cabin for the boat or else it looks weird
true
Very nice boat 🙂🙂🙂
expedition has started
5 minute crafts:exist
Dave:I'm bout to end this man's whole career
😊😊😊😊😊😊😊😊
HĮ
Why you so gay?
Как сделать безпилотник. Автору респект и уважение.
Love your vidoes ❤️❤️❤️
4:40
Davehax: I gave it a bit sand with some *sandpaper*
Me: nice pun
Nobody:
Me at 3am: watching this video
The joke needs salt
@@anbb183 ok
Damn
I’d love to see what this Dave looks like, I can’t imagine the voice to the face LOL.
BTW I like your ideas ☺️
Or go to quirkoligy (his old channal)
I’m first again
nope
Kian Webb nope
Kian Webb ur 3rd
I wasn’t
I mean first to comment
60年代，的自制玩具。👍👍👍
2 views and 9 likes “MOMMMM RUclips’s drunk again”
Stop this
your channel name, description and comment is just wrong
@@lorrainekayelao-estrella8831 99ñ
Much better when you make some people in the boat
Who thinks Dave is geeky?
👇
Finlay FinTGM and your pretty gay huh
Воды только набрал корабель ) А в целом прикольно
Pretty cool, hu?