Homemade PI metal detector-air test depth-Part 1 Импульсный металлодетектор Часть 1
HTML-код
- Опубликовано: 18 сен 2024
- #garrettinfiniumls #vallon #testminelabexcalibur #подводныйпоиск #подводныенаходки #homemadecoiltest #smgolaqualinepi
Part one. - the Self-made metaldetector. Electronics scheme, coil. Measurements of range of detection, coins, rings, chains. Gold, silver, copper, nickel.
---------------------------------------------------------
Самодельный импульсный метало-детектор. Собранная плата электроники, катушка. Первая часть. Замер дальности обнаружения. Монеты ,кольца, цепи и т.д.
Ochen' khoroso.. Prodolzhayte i ne zabud' te zayti i ko mne i davayte podderzhim drug druga 🙏
Молодець!спс за відео цікавий детектор !будемо ждати відео в зборі і можливі тести!
Браво!Добра идея да бъде направен в слушалки.
Добавте пожалуйста в описание под видео pdf и lay файлы чтобы все смогли попробовать сотворить данное устройство.
Really nice video
also please could you give me the circuit or pcb layout?
Hello, .
thank you for sharing and for the effort
I have a question please,
I want to make a gold detector with a depth capability of 12 metres. how to do that?
and I want to create a 3d image for the scanned area.
thank you
12 метров это уже геолокатор/ нейтронный детектор / массспектрометр
Did you use same parts as on sheme or something difrent. Could you give my list of parts you use. Thanks Greatings from Seriba
Блин !!! Приятно посмотреть !!! ....собирал я такой , 12-ть лет назад ,помню умножитель у меня тогда не заработал , пришлось повыш. преобразователь городить (полевик раскачивал с CD4011 через резистор ) кор. всё заработало ...примерно , как у вас дальность обнаружения была ...я тогда доволен бал, как слон..., а кстати.. у вас умножитель напряжения запустился ??
Приветствую. Все запускалось без проблем.
уважаемый расскажи пожалуйста где что померить! нет генерации на базе полевика,какая частота должна идти на полевик?lm318 можно ли ее заменить на tl072,jrc4558,lm358,транзисторы повышения напряжения критичны?
How to make gemstones location mchines please tell me how to make circuit boards sir
Very good video !!!My russian language its not very good but i have some questions1. How much is the coil diameter ?2. How many turns and how much its wire diameter (0.5, 0.3 or 0.6 mm ?)Also, did the pcb circiuit was correct ?.. did you change anything like transistor or something else??Thank you, Andreas
+Andreas Christodoulou Hi. The coil diameter of 20 cm . The number of turns 25. The wire of 0.5 mm . You can use 0.6,0,7 .
The scheme itself unchanged. Fee altered under SMD parts . The transistor 740 in the circuit
+Myntmaster этот прибор различает черный,цветной металл?
+Nail Starпонятно, это типа пирата с которым копаеш все гвозди и весь хлам
Not bad.
Hi sir, my polines pi dedector was working good, but today i can not get frequance..I changed 555 but nothing change..100k trimpot normal, what is the problem...bc357 burn ?
Hello. If the BC357 burns out. The problems may be like this. 1) BC357 is soldered incorrectly. 2) 555 is not working, a constant voltage is supplied to the base of the transistor and it burns out. 3) BD911 burned out. To quickly check you need an oscilloscope. We unsolder the BC357 and measure the frequency on the 555 chip on the third leg. If there is generation, we move further along the chain. If not, change the 555 and check all the wiring around the chip, resistors and capacitors.
@@Myntmaster sorry for my poor english, i could not tell what i ask.I am not shoore bc357 burn out or not.When i put new 555, irf 840 and bd 140 both of them are soo hot , and frequances 0....
@@macittan6602 Understood. Start by checking whether there is a generation signal on the third leg of the 555 chip. If you don’t have an oscilloscope, you can check with regular headphones at least 32 ohms. Connect one pin to the third leg of the 555 chip, the other to the power supply negative. Through a 10 microfarad electrolytic capacitor. There must be sound. By the way, you need to check the voltage on the chip, leg 1 minus, legs 4 and 8 plus 12 volt power supply.
@@Myntmaster i solved the problem.thank for all...i need your suggestion for another adjustment.how can i adjust 220 k trimpot for best frequances and volt.
How to make underground gemstones detector circuit boards. sir. like this is
una condial saludo como podre obtener el diagrama para ser uno mismo
i am doing my project on walk through metal detector. can any one please give the circuit diagram for it. i thought of doing it through magnets but it failed. so please any one give me the circuit diagram.
www.geotech1.com/cgi-bin/pages/common/index.pl?page=metdet&file=/projects/stuart1/index.dat
can you send me the schematic and the diagram sir? thank you?
Sir please let me know the circuit diagram of this detector
Hello. Here reference here all. www.geotech1.com/pages/metdet/projects/stuart1/stuart1_300.pdf
Добрый день ) У меня вопрос как померять потребеление прибора ? Каким способом или прибором ?
Вечер добрый. В разрыв цепи питания ,например по плюсу подключить миллиамперметр или тестер. Замерить ток детектора в покое (отсутствие под катушкой мишени) , и при обнаружении цели (обнаружение мишени)..
please give me diagram and component
diagram ?
hola desde colimbia me puede regalar el pcb y componentes me interesaria gracias desde colombia
show me the diagram sir plz.im here in the Philippines
Diagram pleade sir
надо было микросхемы программировать ?
Нечего там программировать. При исправных деталях и собранной без ошибок схеме. Работать начинает сразу. Схема ,плата, описание по ссылке.
www.geotech1.com/pages/metdet/projects/stuart1/stuart1_300.pdf
+Jeļena Gonšteina Нет не надо. Собирается на раз. Если ничего не напутали и все детали исправные начинает работать сразу.
ну где ссылка на схему?
arg.carioca
если надо про шурф могу видос снять
Всегда интересно посмотреть. Если есть возможность снимайте.
сколько денег на схему ушло ?
Если считать всё. Радиодетали, штанга (она сейчас доделывается), катушка , наушники. Стоимость всего детектора (законченное изделие) 70-100 USD . Надо точнее посчитать. Чисто электронная часть 15- 20 USD.
+Jeļena Gonšteina 100 долларов США
nerci ne prend qua 15 centinetre les objet dapre les composant utiliser set bien jaten tes test esai en terres
шурф берет мизерные цели.датчик витая пара
Шурф это Surf PI ? Мизерные цели,-что за металл, какие размеры предмета-цели ? Золотую серьгу 585 проба, вес 0,5 -1 гр. не застёгнутую на сколько возьмёт ?
English !! Wtf
hahahaha... ar u stupid bro