Very Good Artists 🟢 In this Video you will see how to mount a cladding, with 48mm profiles and a fireproof plate. ▶︎Video transcript: Ready to mount this wall with fireproof plate. As we are going to use 48mm profiles, we place the laser from the wall at least 6cm. I place this piece of cardboard with that line so that when I move the laser from the other end I can see it and make it match up in the middle. We check at several points if we do not have less measure than we need. Here we have the 48mm channel and stud. We will place the acoustic band in the channel that goes to the floor and ceiling. We put the channel on the ground and fix it in line with the laser. Since the wall will end here, we take out a sinker to be able to place the roof channel. We place the channel with the acoustic band and fix it along the laser line. We measure the first stud and cut it. We place it and fix it well to plumb, since it will be the reference for the measurement of the following. Do you need to tape plasterboard? Here is a playlist for you. We hook the meter on the upright and measure every 40cm. For the lower area we do the same: we mark every 40cm. Simple 40 - 80 - 120 - 160 - 200 - 240 - 280 - 320 Now we are placing a stud in each mark. If the measurement is quite equal, we can use the leftover piece of a stud already cut to size as a gauge. We fix them with the axis of the upright at the mark we made. Subscribe! I recommend inserting a reinforcement halfway up. I will give you two ideas. The first idea is: with leftover pieces of channel or stud, we put a brace into the back wall at each vertical stud. You can do this once you have all the studs placed. The second idea is: if we have enough space at the back, we pass a horizontal profile to screw the vertical ones and we put a brace in the wall about every 90cm. We pass this once we have placed a profile. We fix all the profiles above and below, the axis in line with the mark. We fix them to the profile that we pass behind or we put the strap on each one. Once anchored to the wall, we pass the necessary electricity or plumbing pipes. We should never pass the tubes inside the profile like this vertically, because when screwing the plate we will perforate the tube. Once the tubes are placed, we place the insulation. We are cutting the fiber every 40cm for a better placement. Once the fiber is placed, we will put the plates.
Just the video I was looking for. I am framing out a bathroom wall to hide pipes and find it fairly flimsy with metal studs. Thanks for the tips to use braces and channel for support fixings. 👍
Для первого раза не плохо, а вообще: Не кинул правило.... Не поставил сшивки Не разделал кромки Откосы обрезаются ножом, а не ножовкой Делать таким профилем быстрее, но при этом он в два раза дороже потолочного
io ho lo stesso problema che devo fare un isolamento interno su una vecchia casa con muro in sasso smaltato ma irregolare, pero ho visto esistono dei distanziatori fatti a posta per fissare i montanti in punti a parete. volevo chiederti che isolante hai usato?
De dónde sos? Consulta.....le pusiste placa ignífuga por qué? Consulto porque es mi país Uruguay es la más costosa. Saludos. Quedó espectacular el trabajo
*А где поперечный профиль на стыках листа??? И я так и не понял нахрена утеплять этот кусок стены если вся остальная как была каменной, так и осталась?*
haha. sorry no good work. inside insulation and air between the Wall. happy birthday. condenswater is flowing.😅😅😅😅😅 no plastic membrane between insulation and pink Board. da kann man beim Schimmeln der Platten zusehen. innendämmung ist immer kritisch. der taupunkt wandert dadurch nach innen.😅😅
straszne druciarstwo do łączenia profili cd60 że ściana używa się wieszaków ES a nie jak on to robi także łączenie profili cd60 z profilami cd60 łączy się za pomocą łączników poprzecznych cd60 a nie jak on to robi to jest cały system ,wrzucają filmy pseudo profesjonaliści a tak na serio to amatorka na 100% ,czym się tu chwalić, mnie by bylo wstyd to wrzucić na RUclips
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
Very Good Artists
🟢 In this Video you will see how to mount a cladding, with 48mm profiles and a fireproof plate.
▶︎Video transcript:
Ready to mount this wall with fireproof plate.
As we are going to use 48mm profiles, we place the laser from the wall at least 6cm.
I place this piece of cardboard with that line so that when I move the laser from the other end I can see it and make it match up in the middle.
We check at several points if we do not have less measure than we need.
Here we have the 48mm channel and stud.
We will place the acoustic band in the channel that goes to the floor and ceiling.
We put the channel on the ground and fix it in line with the laser.
Since the wall will end here, we take out a sinker to be able to place the roof channel.
We place the channel with the acoustic band and fix it along the laser line.
We measure the first stud and cut it.
We place it and fix it well to plumb, since it will be the reference for the measurement of the following.
Do you need to tape plasterboard? Here is a playlist for you.
We hook the meter on the upright and measure every 40cm.
For the lower area we do the same: we mark every 40cm.
Simple 40 - 80 - 120 - 160 - 200 - 240 - 280 - 320
Now we are placing a stud in each mark.
If the measurement is quite equal, we can use the leftover piece of a stud already cut to size as a gauge.
We fix them with the axis of the upright at the mark we made.
Subscribe!
I recommend inserting a reinforcement halfway up. I will give you two ideas.
The first idea is: with leftover pieces of channel or stud, we put a brace into the back wall at each vertical stud.
You can do this once you have all the studs placed.
The second idea is: if we have enough space at the back, we pass a horizontal profile to screw the vertical ones and we put a brace in the wall about every 90cm. We pass this once we have placed a profile.
We fix all the profiles above and below, the axis in line with the mark.
We fix them to the profile that we pass behind or we put the strap on each one.
Once anchored to the wall, we pass the necessary electricity or plumbing pipes.
We should never pass the tubes inside the profile like this vertically, because when screwing the plate we will perforate the tube.
Once the tubes are placed, we place the insulation.
We are cutting the fiber every 40cm for a better placement.
Once the fiber is placed, we will put the plates.
complimenti per come hai descritto alla perfezione con semplicità anche senza commenti, come realizzare una parete in poco tempo
Just the video I was looking for. I am framing out a bathroom wall to hide pipes and find it fairly flimsy with metal studs. Thanks for the tips to use braces and channel for support fixings. 👍
Для первого раза не плохо, а вообще:
Не кинул правило....
Не поставил сшивки
Не разделал кромки
Откосы обрезаются ножом, а не ножовкой
Делать таким профилем быстрее, но при этом он в два раза дороже потолочного
последний аргумент - самый главный.
good teacher!!!
능력자시군요!!👍👍👍 You're amazing.😍😍
у нас из таких делают перегородки , а обшивают другими профилями , те что идут на потолок и они удобней и практичней будут , для обшивки стен
Обшивают и такими, есть облицовка С-625 и С-626 в техничке Кнауф
@@knauf-masters дорого только вот.
Salamat sa mga turo. Nakakakuha ako ng ideas
With what do we cover up the gap between the board and the floor at the bottom?
Very good , best workmen ship
finally...thanks!
What tools did you use the yellow one 🤔
Inch Handle Crimping Pliers Stud Crimper Plaster Board Drywall Pliers For Fastening Metal Studs Punching Pliers Repair
io ho lo stesso problema che devo fare un isolamento interno su una vecchia casa con muro in sasso smaltato ma irregolare, pero ho visto esistono dei distanziatori fatti a posta per fissare i montanti in punti a parete. volevo chiederti che isolante hai usato?
which one better between screw and stud
Great video… just what i needed, thanks 🎉 How did you screw direct into the stone / concrete….did you use a plug or a special screw?
Broca y tornillo, como normalmente hacemos....
You are using liner lezar what is that aliegment
What type of tape pasting lower of panel please guide
What is the name of the Pneumatic Hammer used to attached the metal frames to the concrete?
De dónde sos? Consulta.....le pusiste placa ignífuga por qué? Consulto porque es mi país Uruguay es la más costosa. Saludos. Quedó espectacular el trabajo
Español, simplemente era una muestra de esa placa para el vídeo.
Great work
*А где поперечный профиль на стыках листа??? И я так и не понял нахрена утеплять этот кусок стены если вся остальная как была каменной, так и осталась?*
Çok güzel eline sağlık hocam iyi ki varsın hocam hayırlı akşamlar hocam
nice video
If the height its bigger than the steel length, how do you procedure?
Overlap and screw together
What is the circular tool what you used to make signs on the drywall element where the wall wasn't straight at the end? ( 12:50 )
Im interested too
Drill a hole middle of a pickle jar lid, stick a pencil in it and job done :)
Metal to metal "Pan Head screws"....Stronger fix.
Hola . ¿Qué es esa cinta que pusiste debajo del perfil?
For this job you need profiles U30 and CD 60...you lose more space whit U100& C100.
Por que no usaste placas más altas a si no te quedan uniones horizontales??...
What the useful video sir. What we call the metal name and model sir?
Whats the black roll of tape you applied?
Sound isolation -black tape.
@@maksbrovler3466 cheers mate.tnks for reply!
Thanks
thank you bro.
¿Que aislante usas?...
いい動画ですね 工事は、世界共通
this beautiful stone wall does not deserve this garbage, its a crime. the whole process is like a funeral
A good job ! 😊👍🏼
Thanks for sharing but the title says' how to' and there's no instruction. 😕
I also it's work in Saudi Arabia 🇸🇦 where from you brother.
The stone wall is much better than the dry wall,
Como se llama la herramienta para perforar y fijas el metal con metal
Po prostu zaciskarka do profili lub szczypce do Łączenia, polecam tanie magnusson lub knauf ,Yato lub drogie w zakupie ale porządne z firmy EDMA
като утепляет внутри помещение стекловатой?! только штукатурка с перлитом и все.
Perfect
never need to drill under the dowels in the seams of the tile (any) !!!
qué tipo de tornillos se utiliza
I th😅nk I learned what music he likes more than how to use it
Your work is perfect...?
no VCL ???
эхх,такая красивая стена-была...
Why would anybody cover that beautiful stone wall
because it’s cold wall
I would have worked for Abel if he had called us
Gut Job, aber einige Sachen du bist falsch gemacht
A 🪚??
круто красава
This is residential, not commercial
❤️👍💪
want tools for this 4:35
читайте техническую документацию производителя перед началом монтажа, а не сочиняйте свой бред, а потом ещё это выкладывать в сеть. Зачем???
glボンドでボードを貼るやり方もあるので
Le cimentage et plafonnage , vous ne connaissez pas ????
Зачем то построил перегородку возле стены. Непонятно.
haha. sorry no good work. inside insulation and air between the Wall. happy birthday. condenswater is flowing.😅😅😅😅😅 no plastic membrane between insulation and pink Board. da kann man beim Schimmeln der Platten zusehen. innendämmung ist immer kritisch. der taupunkt wandert dadurch nach innen.😅😅
Is it that pink is water resistant board 🤔😉 or is pink for fire?
Less music and more details
kemm in oxx
Hay un error cuando puso el pedazo de panel arriba no puso metal en la división queda debilitado
NO es necesario, la cinta basta.
Видео " как делать нельзя".
Не повторять!
Thumbs down. Please don't use the word "Tutorial" and then just assault our ears with horrible music. Totally disappointed.
Doesn't your TV have a volume control? 🤦♂️
Always you're doing alone work
Der schimmel ist da .Erst schimmel sanieren vile Sache falsch.....
За труды видео 5 . Остальное 2 несоответствие названию
Неправильно брак работа стики надо продолни профила кинут АТО трешенку будит
Annoying music 😬
когда коту делать нечего..
straszne druciarstwo do łączenia profili cd60 że ściana używa się wieszaków ES a nie jak on to robi także łączenie profili cd60 z profilami cd60 łączy się za pomocą łączników poprzecznych cd60 a nie jak on to robi to jest cały system ,wrzucają filmy pseudo profesjonaliści a tak na serio to amatorka na 100% ,czym się tu chwalić, mnie by bylo wstyd to wrzucić na RUclips
Que lástima tapar esa pared tan bonita con esa porquería de pladur.
Should be criminal to cover up that wall
🤣🤣🤣👎🙆🤦
Ужас!
;;oDDD
No need for so much screws for the vertical studs . Just put them inside , no screw needed
Отвращение от всех ваших ремонтов и вас