CUSTOM ENGINE HOIST MODIFICATIONS
HTML-код
- Опубликовано: 27 сен 2021
- This video shows the custom improvements I have made to a standard engine hoist, to make it stronger and more capable and easier to use.
Disclaimer:
This video is for entertainment purposes only. Due to factors out of the control of freeidaho, we cannot guarantee against improper use or unauthorized modifications of this information. There is no warranty written, expressed, or implied for accidents, injury or damages that may result from using any information in this video. Freeidaho assumes no liability or responsibility for property damages or injury incurred as a result of any information contained in this video. Use this information at your own risk. Any injury, damage, or loss that may result from improper use of tools, equipment, or from the information contained in this video is the sole responsibility of the user and not freeidaho. Be safe!
Thank you for watching. As usual, if you found my video useful or interesting, please click the Like button. If you want more motorcycle-related and fabrication-related videos, please click Subscribe and click on the Notification Bell.
Please leave me a comment about your thoughts. It can be simple or long, it can be stuff I need to do better or stuff you liked, or topics you would like to see covered. Virtually anything would be appreciated.
Nice ideas. Never be afraid to modify and be free.
Thank you!
I like the mods, especially lowering. One mod iI made is to epoxy a round water spigot 'handle to the relief valve. it allows me the kind of control you mentioned with the winch. Great job.
Thank you!
These are some top notch mods! Thanks for the inspiration.
Thank you Sir! Good luck!
Excellent mods. To your shop crane. I also added a hand winch and pulley to my crane for lifting in tight spaces like under a camper shell.
Thank you Sir! I'm not sure why a hand winch and pulley are not part of a standard engine hoist. But cheap ones up to expensive ones don't seem to do it.
Thanks for watching!
I have 2 hoists...I definitely want to mod my smaller hoist like this one to use just for engine lifting, but I now want to lowride both of them...awesome video...🖖🏿😎👍🏿
Thank you Sir, good luck!
Ideas are spread like wildfire.....Thanks!
Thank you!
Cool man. Nice shop, thanks for sharing!
Thank you for the kind words.
Хорошая работа, инженерный подход к конструкции крана, грамотно занизили раму что позволит без труда подкатить под низ автомобиля
Thank you!
Excellent!!
Thank you!
I like the height-lower hack.
Thank you Sir. My milling machine base is very low, and I made it to roll under there.
one other conversion i seen on a enginehoist was to put a lever or watertap knob to the releasevalve of the hydraulic cilinder , that way you dont need the pump arm to lower the boom , it allso gives you a little more leverage to be able to release the valve a little more carefully
i have a foldable version that if you take out the bottom bolt of the hydraulic cilinder can be made pretty compact for storage
i agree that the foldable one is less stable when lifting (it basicly drops forward about 2 inches when you put a load on it ) and youre correct that its a verry usable item to have if youre lugging heavy stuff around
Good idea, I did that for my hydraulic press here ruclips.net/video/HniXePBjjI0/видео.html
I'd siggest adding a hoop top the pulley to prevent the cable from coming off.
Thanks! In several years of usage, I have had no problems with the cable coming off of the pulley. The pulley is for about 3/4" cable or rope, so the groove is very deep.
I have to wonder if the lowrider mod reduces the capacity though, because now instead of the weight transferring to the wheels through a full box section of tube, now it's sitting on basically plate, which doesn't have as much strength in the vertical direction. I think if you wanted to do that, c channel should be used to retain more rigidity and strength from the frame to the wheels. Maybe the plate is thick enough to take the load though, you'd have to look it up in a structural steel chart. You did do a good job of reinforcing the boom where you added the pulley though!
Not a problem. Check out 2:44 in the video, which clearly shows reinforcement on the sides, "like a C channel" with room for the swivel caster wheel to turn. It is all made from 1/4" plate steel, unlike the square tubing which is about 16 gauge.
So far the heaviest thing I have lifted is 1400 lbs, without any flex anywhere.
nice work! Do yo have a video on your motorcycle lift or air compressor?
My moytorcycle lift and air compressor are shown briefly in this video ruclips.net/video/WMM1ffPIJt0/видео.html
What's the thickness measure for the metal bar bro?
I added metal bar stock in three places and you didn't say which.
1) Inside the boom to mount the pulley. 2) On top to strengthen the truss. 3) And to mount the caster wheels when the lift was lowered. The first two have dimensions given in the video. The wheels were cantilevered out with 1/4" thick bar stock.
@@freeidaho-videos randomly...
Trying to make one that can fit in the back of my truck so can haul heavy things away..
You may want something like this. ruclips.net/video/GQW25W6XLug/видео.html