Thank u after Taking it to the watch repair shop they told me it was done for after watching the video I change the original battery for the 1st time after 10 years and Wala back to life
Even after you reset and you don’t see any digits, it could be because the contacts on the back of the battery aren’t making a good enough connection. The old battery has probably been in there for several years and those contacts are flattened down. The remedy is to take the battery out and use a tweezer to pry them up just a little bit so they make a better connection. It may take a couple of tries. I also recommend putting a little silicone grease on the rubber gasket to try to maintain the water resistant rating for this watch. It doesn’t guarantee that, but it will help.
I had the same issue. I bent the contacts like you said and it wasn't quite working still. I applied a lot of random brute finger pressure to various parts of the watch face and then it started working. May have pressed a button or two also.
this did it for me. removing the battery and bending the contacts on the bottom to look further up so they press harder against the new battery. In combination with the short-circuit that can be seen in the video I feel like a hacker now, lel. also It was necessary to bend the contact plates from the 3 buttons on the sides to make the buttons work again. probably because of me fumbling around too much. My display had some minutes tho show numbers but not fully. It came back fully readable after some 1-2 minutes, though.
For anyone wondering with a Casio W-59 (very similar watch) on how to reset the CMOS (AC), I could only got it to by connecting the AC terminal directly with the + side of the battery
If the display shows random things, u have to RESET. Short circuit the AC (All Clear) point. This is a TINY hole, one from the many on the face (Top/North), a very hard to read sign indicates it. Try to move into the light to reflect for easier readability. Than use some metallish, thin tool to short the circuit. I used a clips, folded back to CONNECT THE BATTERY WITH THE AC POINT.
i managed to do the AC thing, and i got results, the watch shows all the right things, but some of the segments just dont show at all. worried that the watch might just be broken, i just got the watch today, and the display was missing segments before i had even opened it. do you have any tips, or is this a lost cause?
@@johne6081 Ensure one tweezer end pokes into the AC (all clear) hole, and other tweezer end should simultaneously touch the silver metal battery clip you just pressed on. That should reset it back to 1200 on Sunday 1. GL!
@@freedom55or95 Typo and I have the problem of dark segments, which evidently is related to the conductive rubber strip that connects the LCD display to the circuit board.
@@raouloctav Thank you for the reply. I did that a few times. I fiddled with it for more than an hour with no success. It might just be a problem with the quartz oscillator or a bad solder joint somewhere. It's a used watch I received without the battery so I have no idea if the problem existed before.
:) a fost un proiect din perioada comunista a unui mester, am vazut ceva similar la Gerber , lansat acum in 2020. ceva tip maceta, nu am numele acum dar poti cauta Gerber shotshow 2020
Thank u after Taking it to the watch repair shop they told me it was done for after watching the video I change the original battery for the 1st time after 10 years and Wala back to life
Voila not wala :)
Voila not wala :)
They want you to buy a new watch lmao
Even after you reset and you don’t see any digits, it could be because the contacts on the back of the battery aren’t making a good enough connection. The old battery has probably been in there for several years and those contacts are flattened down. The remedy is to take the battery out and use a tweezer to pry them up just a little bit so they make a better connection. It may take a couple of tries. I also recommend putting a little silicone grease on the rubber gasket to try to maintain the water resistant rating for this watch. It doesn’t guarantee that, but it will help.
I had the same issue. I bent the contacts like you said and it wasn't quite working still. I applied a lot of random brute finger pressure to various parts of the watch face and then it started working. May have pressed a button or two also.
this did it for me. removing the battery and bending the contacts on the bottom to look further up so they press harder against the new battery. In combination with the short-circuit that can be seen in the video I feel like a hacker now, lel. also It was necessary to bend the contact plates from the 3 buttons on the sides to make the buttons work again. probably because of me fumbling around too much. My display had some minutes tho show numbers but not fully. It came back fully readable after some 1-2 minutes, though.
Dude you saved my watch! Thank You so much!!!!
Thanks dude .. saved my 16 years old F91w
For anyone wondering with a Casio W-59 (very similar watch) on how to reset the CMOS (AC), I could only got it to by connecting the AC terminal directly with the + side of the battery
Thank you!! It works. :]
Thanks a lot - used a paper clip to do the 2.22 reset ;) So good to not just get another watch!!!
i didnt understand. what makes AC ? All clear??
If the display shows random things, u have to RESET. Short circuit the AC (All Clear) point. This is a TINY hole, one from the many on the face (Top/North), a very hard to read sign indicates it. Try to move into the light to reflect for easier readability. Than use some metallish, thin tool to short the circuit. I used a clips, folded back to CONNECT THE BATTERY WITH THE AC POINT.
Thank you mate, it is working again.
I removed the sticky piece of white paper, does it matters?
I also have this question.
😂 thanks a lot,I wanted to throw the watch in the trash before this video
Did the beep sound go away after battery replacement?
Buen trabajo,me ha salvado,muchas gracias!
My watch gets blinking the digits I used to watch your video and do like the way you does but it has a difference I just losses ah one screw here ?
Thanks a bunch. Saved mea watch!
GRACIAS!
Thank you, it works
It is a CR2016 Battery
i managed to do the AC thing, and i got results, the watch shows all the right things, but some of the segments just dont show at all. worried that the watch might just be broken, i just got the watch today, and the display was missing segments before i had even opened it. do you have any tips, or is this a lost cause?
That is precisely my problem, as well. I replaced the battery, and now I can't get all segments to light.
@@johne6081 Ensure one tweezer end pokes into the AC (all clear) hole, and other tweezer end should simultaneously touch the silver metal battery clip you just pressed on. That should reset it back to 1200 on Sunday 1. GL!
@@freedom55or95 Typo and I have the problem of dark segments, which evidently is related to the conductive rubber strip that connects the LCD display to the circuit board.
What are the prongs called to reset the AC. I’m trying to find some but not sure what to search.
Metal tweezer(s)
Saved my butt, I thought all was lost.
thank you so much!
Thank you so much
What is the size of the screw used in that watch?
It's a really small Philips, but i do not know the size. What i can tell you, it's standardized on lower ends Casio
It's the same which is normally used in eye glasses. I just got one from my local eye glasses shop and it was the perfect fit. Hope it helps.
2:23 after AC no display,why?
the VERY IMPORTANT part is not in video!!!!
I tried this but my LCD still doesnt work
Tks
My screen flickers after changing the battery, The AC reset doesn't fix it.
Hy. Check if everything is seated correctly. Replace or reseat the battery
@@raouloctav Thank you for the reply. I did that a few times. I fiddled with it for more than an hour with no success. It might just be a problem with the quartz oscillator or a bad solder joint somewhere. It's a used watch I received without the battery so I have no idea if the problem existed before.
What happens if i use a cr2032 battery?
I believe it's too thick
I’m 7 and use this watch dayliy
My watch remained dead... :(
The old battery was certainly discharged: 0.3V So I don't know what happened.
Well, after some adjustments it came back to life.
Sall de unde pot achizitiona palosul lui greuceanu
:) a fost un proiect din perioada comunista a unui mester, am vazut ceva similar la Gerber , lansat acum in 2020. ceva tip maceta, nu am numele acum dar poti cauta Gerber shotshow 2020
@@raouloctav mulțumesc
Thanks..after i replace battery..alarm sound no longer work
Hi ..remove the back cover and arrange it correctly, make sure the alarm pins are aligned with back cover speakers.
@@ranjankc121, you are right, the piezoelectric speaker needs to have contact to work properly, this if it has not gone kaput.
@@ranjankc121 thank you!!!
@@lorenzodelotto9690 your welcome...
after assmbling back cover (metal) then gonna work. try it before screwing. you ll see. ( i was terrifed same.. then i see)
I replaced battery my Casio watch but my watch was not working 😭😭
Please do something
It's taken years for anyone to reply to you but rest assured, I have now done something.
Use gloves
I didn't and I broke my watch