The board takes power from motor/ESC 1, but there is no need to remove the other power pins from the ESC's. I have built dozens of KK2 copters in every configuration and never had an issue. - Matt
You guys are correct, it's a 20 Amp max board. I tested the copter and I'm only drawing 19 Amps max and only for a fraction of a second at full throttle, the 30 Amp afros are total overkill. A direct harness would probably be better, but it's been fine so far and nothing on the copter gets at all warm in flight. My guess is that the distribution board is a bit under-rated. - Matt
Hi Matt, Absolutely brilliant series, very informative, Thanks, I've recently purchased the HK Scorpion Y650, KK2 1.6ver and gimbal and just getting it to fly now, any chance of a video on that model? Cannot get my gimbal to work though! Good work, many thanks and keep it up, Mark.
Hello Matt. I get this question once a day on the chat system at HK. Which one of the ESC BEC servo leads does the KK2 get it power from? I assume only one is tapped (to avoid voltage/current loading). Does the builder have to remove all of the unused plus (red) center leads from the other 3 ESC BEC's?? thanks. Robert Veach HK PS # 4
Matt, an Idea I have had is for a kit with everything needed to make a bare bones quad using the SK450 frame. Are there any plans for that at HK? I am hesitant to go out and spend on something I have no idea if it is right or not. Great series. I have the quad itch now!
i have a fly sky ct-6b transmitter and receiver i really don't know how to interface it with kk2.1/kk2.0 please help me , nor i know what settings to apply in t6 config please help me out.
I have the TBS discovery knock off. It seems the arm configuration is the opposite of this one. Looks like the TBS has the front arms shorter instead of longer so would the same setup go for the TBS as this one . Any help would be appreciated. My first quad and I did it from scratch. Seems to be functioning well just cant get it stable and very new to the quad thing. Before this I only flew planes.LOL.. Thanks in advance for any help.
Hi! Now I'm trying on Vertical Take off and Landing(VTOL) RC aircraft with two motors each at the wing tip , which is referenced to Tom Stanton's VTOL V2. And I'm using that Hobby King KK 2.1 Flight controller board to stabilize the aircraft. I find it difficult with some settings. And I'm wondering if you could help me with that.
Awesome video! So much to learn. I would like to build my own SK450 like the one you built in this video. You listed some of the major parts. Do you have a complete list of everything you used? Some of the parts were on back order from Hobby King. Can you recommend alternative parts for the ones that are on back order? The frame, motors and ESC's are not available right now and from some of the past posts that seems common. Do you recommend the SK450 for a beginner? I'm dying to get started! :)
Hi Matt, I'm about to set out on my first quad build & would like some advice. I am going to go with SK450 (with Dead Cat upgrade), Turnigy Aerodrive SK3 motors & 10" props. I am going to use a KK2.1HC, & I'm contemplating using a Qbrain 4x25a rather then 4 x individual ESC's. I noticed watching all your videos that you have never used the Qbrain on any of your builds & was wondering why? Is it an inferior setup as opposed to 4 x 30a Afro's?
Hey , can you help me with my quadcopter when ever i push the throttle the copter spins ccw and dose not strate upward i m working with kk2.1.5 with 30a ecs on f450 with fs-ct6b tx,vx
I have the same props, motor and mount kit. None of the spacer rings fit exactly. The closest fit barely goes over the thread of the mount kit if I screw it on. How do you get the props all the way down? Just force it with prop nut or do you drill them out a bit?
Hi, Having watched the video I have purchased (from HK) a X550 frame, Turnigy 2830 100kv motors and 10x4.5 props. Will your setup for the SK450 work for this setup as well.
330mm dead kitten? I'll take one. The SK450 gets a bit bigger when you change to a deadcat. And how did he attach his headlight? Or how do you attach accessories to booms for that matter. Also, how did you cover up your power distributor to keep it from shorting accidentally by debrie? I slathered all the contacts with hot glue all over mine and keep wondering if there was a better way.
awsome so much info. hey could you tell me what numbers i should use for the 500 size hercules from hk please thanks ps i threw these numbers in it i havent tried it yet though.
I have a f450 frame, 1000kv motors, x configuration, simonk 30a esc, kk2.1.5, I have tried absolutely everything but every time I try to take off it wants to flip to the right. what should i do.
Check if your motor leads are connected to the KK board in the right order, that was my problem. Had to find the solution on my own sadly... Also check if your props are put on correctly (CW, CCW).
Bought one of these flight controllers a few weeks ago. So far I like it. So, I decided to get another one, for just in case. Nobody has them? I’ve been looking all over, no luck.anybody know if they are available? Or when? Tia.
hi any chance on doing a vid on re flashing the Afro's ,, as im running Turnigy Multistar 4220-880Kv on them and they are cutting the motors randomly red light flashes when it cuts
ive been having trouble with getting mt kk2 to fly right, ive been using normal turnigy plush 30A esc's. i have ordered some 30A afro esc's, will these make a big difference? or should i have no trouble with plush esc's?
My KK2 quadcopter that I built with parts from hobby king two or three years ago was never able to fly and I try again to get it to work every couple of months. When ever I try to fly it, on take off it flips and sometimes in random directions and it turns in random directions. I have all the right types of blades and they are spinning in all the right directions, I have calibrated everything, and updated the firmware. Please help. My problem looks like this: ruclips.net/video/oAyggHIr_Qs/видео.htmlm2s
The board takes power from motor/ESC 1, but there is no need to remove the other power pins from the ESC's. I have built dozens of KK2 copters in every configuration and never had an issue. - Matt
You guys are correct, it's a 20 Amp max board. I tested the copter and I'm only drawing 19 Amps max and only for a fraction of a second at full throttle, the 30 Amp afros are total overkill.
A direct harness would probably be better, but it's been fine so far and nothing on the copter gets at all warm in flight. My guess is that the distribution board is a bit under-rated. - Matt
I've built a lot of multiwii copters, the boards tend to come with those wires. I'll see what we sell at HK that is comparable and post a link. - Matt
Hi Matt, Absolutely brilliant series, very informative, Thanks, I've recently purchased the HK Scorpion Y650, KK2 1.6ver and gimbal and just getting it to fly now, any chance of a video on that model? Cannot get my gimbal to work though! Good work, many thanks and keep it up, Mark.
thanks Matt for the quick response.
ESC calibration can be done with the KK board. I'll cover it in the next episode.
- Matt
Hello Matt. I get this question once a day on the chat system at HK. Which one of the ESC BEC servo leads does the KK2 get it power from? I assume only one is tapped (to avoid voltage/current loading). Does the builder have to remove all of the unused plus (red) center leads from the other 3 ESC BEC's??
thanks.
Robert Veach HK PS # 4
Coming soon to Hobbyking DeadKitten! I can't wait!
The props are 9 x 4.7 Turnigy slow fly. - Matt
Matt, an Idea I have had is for a kit with everything needed to make a bare bones quad using the SK450 frame. Are there any plans for that at HK? I am hesitant to go out and spend on something I have no idea if it is right or not. Great series. I have the quad itch now!
Great series guys, way to go!
i have a fly sky ct-6b transmitter and receiver i really don't know how to interface it with kk2.1/kk2.0 please help me , nor i know what settings to apply in t6 config please help me out.
I love those headlights on the 450. Are they available at HK or where?
Hi Matt,
Can you tell me what LED lights you use? They look like small headlights.
Fantastic series of vids - helping me heaps. M
I have the TBS discovery knock off. It seems the arm configuration is the opposite of this one. Looks like the TBS has the front arms shorter instead of longer so would the same setup go for the TBS as this one . Any help would be appreciated. My first quad and I did it from scratch. Seems to be functioning well just cant get it stable and very new to the quad thing. Before this I only flew planes.LOL.. Thanks in advance for any help.
Hi! Now I'm trying on Vertical Take off and Landing(VTOL) RC aircraft with two motors each at the wing tip , which is referenced to Tom Stanton's VTOL V2. And I'm using that Hobby King KK 2.1 Flight controller board to stabilize the aircraft. I find it difficult with some settings. And I'm wondering if you could help me with that.
Awesome video! So much to learn. I would like to build my own SK450 like the one you built in this video. You listed some of the major parts. Do you have a complete list of everything you used? Some of the parts were on back order from Hobby King. Can you recommend alternative parts for the ones that are on back order? The frame, motors and ESC's are not available right now and from some of the past posts that seems common. Do you recommend the SK450 for a beginner? I'm dying to get started! :)
I've set up the KK2 properly but cant seen to stat the motors. Is there a specific stick sequence you must do in order to start the copter?
when will you build hexadrone with kk2.0 broad. Also how do you know which wire will connect from kk2.0 board to receiver? Thanks
Where did you get these very cool front white lights???
Hi Matt, I'm about to set out on my first quad build & would like some advice. I am going to go with SK450 (with Dead Cat upgrade), Turnigy Aerodrive SK3 motors & 10" props. I am going to use a KK2.1HC, & I'm contemplating using a Qbrain 4x25a rather then 4 x individual ESC's. I noticed watching all your videos that you have never used the Qbrain on any of your builds & was wondering why? Is it an inferior setup as opposed to 4 x 30a Afro's?
Mike, I am want to do the same. What configuration did you come up with and are you happy? What components did you use and what did you spend?
Did i miss the prop size? Great episodes guys love the sk450. :-)
I have the deadcat pro with the upswept arms. will that effect any of the pid settings or will this configuration work?
+johnny benvenuti Shouldn't change too much.
Hey , can you help me with my quadcopter when ever i push the throttle the copter spins ccw and dose not strate upward i m working with kk2.1.5 with 30a ecs on f450 with fs-ct6b tx,vx
I have the same props, motor and mount kit. None of the spacer rings fit exactly. The closest fit barely goes over the thread of the mount kit if I screw it on. How do you get the props all the way down? Just force it with prop nut or do you drill them out a bit?
is this same for H Quda?
nice for att the newbs out there (including me) that someone actually tell you how to set thigs up propperly to begin with
Have you got link to the power distribution board please, also the the board that i think is the right one only has a max amp output of 20.
Hi, Having watched the video I have purchased (from HK) a X550 frame, Turnigy 2830 100kv motors and 10x4.5 props. Will your setup for the SK450 work for this setup as well.
I changed all the settings how you showed. (I have the sk450)
And it still oscillates whenever i take off :/
330mm dead kitten? I'll take one. The SK450 gets a bit bigger when you change to a deadcat.
And how did he attach his headlight? Or how do you attach accessories to booms for that matter.
Also, how did you cover up your power distributor to keep it from shorting accidentally by debrie? I slathered all the contacts with hot glue all over mine and keep wondering if there was a better way.
awsome so much info. hey could you tell me what numbers i should use for the 500 size hercules from hk please thanks ps i threw these numbers in it i havent tried it yet though.
I have a f450 frame, 1000kv motors, x configuration, simonk 30a esc, kk2.1.5, I have tried absolutely everything but every time I try to take off it wants to flip to the right. what should i do.
Check if your motor leads are connected to the KK board in the right order, that was my problem. Had to find the solution on my own sadly... Also check if your props are put on correctly (CW, CCW).
Bought one of these flight controllers a few weeks ago. So far I like it. So, I decided to get another one, for just in case. Nobody has them? I’ve been looking all over, no luck.anybody know if they are available? Or when? Tia.
Hi Will theses setting work well on a bumble bee quad copter thanks
hi any chance on doing a vid on re flashing the Afro's ,, as im running Turnigy Multistar 4220-880Kv on them and they are cutting the motors randomly red light flashes when it cuts
As others have posted and no reply, I have the same question: What are the headlights "eyes" you're using on this model?
What Props are you using on this?
What about Expo settings?
ive been having trouble with getting mt kk2 to fly right, ive been using normal turnigy plush 30A esc's.
i have ordered some 30A afro esc's, will these make a big difference? or should i have no trouble with plush esc's?
hey do you have to set the throttle range on each esc before installing them ?
Will that distribution board handle 30amp esc's? The web site said 20amp (max) I thought?
When will the KK2.0 re-stock in the International Warehouse?
After connecting everything the display at on the kk is blank
Please help me
which configurations for a hexacopter with kk2.1.5 ?
after connecting all the things kk2.1.5 display gone
please help me urgently
which battery are you using for this quad?
Where I can buy? KK 2.0 has gone in int. store
can you do smthin like this for kk v5.5 board
What size props are on this quad?
My KK2 quadcopter that I built with parts from hobby king two or three years ago was never able to fly and I try again to get it to work every couple of months. When ever I try to fly it, on take off it flips and sometimes in random directions and it turns in random directions. I have all the right types of blades and they are spinning in all the right directions, I have calibrated everything, and updated the firmware. Please help.
My problem looks like this: ruclips.net/video/oAyggHIr_Qs/видео.htmlm2s
You can use the KK2.1 board :)
Where did you get those lights?
can i run afro escs on stock sk450 quad ?
good info on these vids thanks ,,, Bart
enjoyed the clock face tattooed ..... Congratulations on the video I'm doing adjustment plate k2.2
I am tattoo artist, very original idea ....
I didn't see the trees moving in the winds.
Your's pi settings is not stable in my Quadcopter
it does shake a bit. But very stable anyway
I know its wired, but in the speed up part of the building i just watched the ice in the glass melt :)
Please any one tell me about pi settings in kk2.1.5
Hey nice watch!
What is “ p gain & i gain” and “p limit & i limit”
what kind of prop
Nice Mazda Miata ;)
Close call at the end. You may want to consider freezing some s p e r m, just in case! :)
I saw Tyler Durden.
Woot - thanks for killing the HK music, picking something decent, and turning it down while talking! :)
I want a Dead Kitten...
my 1motor fast ho jite ha
Dont do a dead kitten, do a DEAD MOUSE, and use the dead cat to chase it. OR 5 dead cats chasing 1 mouse.
woo first comment again
DEAD KITTEN!!!!! ....ROTFLMAO!!... :)
Where I can buy? KK 2.0 has gone in int. store