My understanding is that the proper way to level the blade is by adjusting the two allen head set screws located at the base edge of the blade. NOTE: NEVER ADJUST THE SCREW FOUND IN THE CENTER HOLE OF THE BLADE. The way you demonstrate will may not remain in proper adjustment due to vibration of the machine causing the blade to slip out of adjustment. That is the purpose of the TWO leveling screws (NOT the two phillips head screws that secure the blade). They allow the blade to rest against them holding them solidly in position and preventing downward slippage when machine is in use. Another note: When tightening the two phillips head blade screws ALWAYS tighten the front screw first (as you correctly demonstrated). This prevents the torque from causing the opposite end of the blade to rise up while tightening causing the blade to be improperly positioned. This is a great video so don't think I'm criticizing. I have been dealing with these machines since the early '90's and had to learn these things the hard way. Hope this is helpful.
Is it ok to put lubricant between blade and blade shield to prevent rusting? Also would you be able to tell me where I can find the wiring diagram for this model as I’ve stripped down my machine to give it a full clean etc etc and for some reason (disconnected a connection and forgotten it’s place) it’s not turning on but there is power to the motor. It could also be a faulty switch as it’s been dormant for quite some time. Thanks
My swan machine blade barely moves past that leveling technique in the video when spinning the wheel to the left. I bought a polar pal from Amazon and that one goes up against the metal plate. What could be wrong? At its lowest point it goes 1/8 of an inch below the metal plate.
@@Christopherj1225 yea been looking the past couple hours used machines range from 400-2000 and new go for 2000 plus new but I don't really trust half these websites.seen the used ones most have big holes or look like crap or like you said are rusted 😒 man could make bank on hot days like this if I had one of them
@@icyskyy5875 Thanks for quick reply my swan 100e been sitting in my garage coverup for the last 5 years it still works g8 what a machine I sold maybe 100 customer before I stored it, blades looks in Excellent shape, Should I just buy a new one instead? Thanks In Advance
@@icyskyy5875 Wow!! What a machine it's the swan 100 manufactured in 88 according to stamp date.. going to buy concentrate mix from you guys. It's true that 1 concentrate gallon makes 32 gallons? How do I place my orders
Drew BBQ yep, it’s definitely high quality made to last! Yes, 1 gallon standard concentrate will make 32 gallon syrup. You can place your order at our website www.icyskyy.com. We look forward to working with you!
My understanding is that the proper way to level the blade is by adjusting the two allen head set screws located at the base edge of the blade. NOTE: NEVER ADJUST THE SCREW FOUND IN THE CENTER HOLE OF THE BLADE.
The way you demonstrate will may not remain in proper adjustment due to vibration of the machine causing the blade to slip out of adjustment. That is the purpose of the TWO leveling screws (NOT the two phillips head screws that secure the blade). They allow the blade to rest against them holding them solidly in position and preventing downward slippage when machine is in use.
Another note: When tightening the two phillips head blade screws ALWAYS tighten the front screw first (as you correctly demonstrated). This prevents the torque from causing the opposite end of the blade to rise up while tightening causing the blade to be improperly positioned.
This is a great video so don't think I'm criticizing. I have been dealing with these machines since the early '90's and had to learn these things the hard way. Hope this is helpful.
Is it ok to put lubricant between blade and blade shield to prevent rusting?
Also would you be able to tell me where I can find the wiring diagram for this model as I’ve stripped down my machine to give it a full clean etc etc and for some reason (disconnected a connection and forgotten it’s place) it’s not turning on but there is power to the motor. It could also be a faulty switch as it’s been dormant for quite some time. Thanks
in the description on the machine it states to turn the knob all the way to the right but in this video you turn the knob all the way left ??
Having trouble with ice getting between blade and ice block. Any ideas. Blades are sharp and calibrated. I do have SNO flo's on mine machines.
Que página recomiendas para la compra de las cuchillas
Can it shave thicker ice instead soft like real snow?
yes, you can adjust the ice texture from fine to coarse by adjusting the Blade adjustment knob. Hope this helps!
@@icyskyy5875 thx
My swan machine blade barely moves past that leveling technique in the video when spinning the wheel to the left. I bought a polar pal from Amazon and that one goes up against the metal plate. What could be wrong? At its lowest point it goes 1/8 of an inch below the metal plate.
How much did you get yours for 2g is a lot
@@zurz060 I bought the used swan for $600. The base is very rusty and I had to buy a drip tray for it separately.
@@Christopherj1225 yea been looking the past couple hours used machines range from 400-2000 and new go for 2000 plus new but I don't really trust half these websites.seen the used ones most have big holes or look like crap or like you said are rusted 😒 man could make bank on hot days like this if I had one of them
How many usages before replacement of new blade
Drew BBQ it is recommended to change the blade approximately every 3000 shavings.
@@icyskyy5875 Thanks for quick reply my swan 100e been sitting in my garage coverup for the last 5 years it still works g8 what a machine I sold maybe 100 customer before I stored it, blades looks in Excellent shape, Should I just buy a new one instead?
Thanks In Advance
Drew BBQ if it’s only been used for 100 times or so, the blade is probably still good unless you see a lot of chips or damages on the blade.
@@icyskyy5875 Wow!! What a machine it's the swan 100 manufactured in 88 according to stamp date.. going to buy concentrate mix from you guys. It's true that 1 concentrate gallon makes 32 gallons? How do I place my orders
Drew BBQ yep, it’s definitely high quality made to last! Yes, 1 gallon standard concentrate will make 32 gallon syrup. You can place your order at our website www.icyskyy.com. We look forward to working with you!