Hi, I just finished installing my awning shade but i have not tightened everything down. When I opened the shade it slopes down too low around 45 degrees. how do I adjust so that the end is higher, like 10 degrees slope?
Easy, look for the two nuts that can adjust the slope on both sides of the bar. Loosen it, turn toward the directions of the wall, then tighten the nuts again. The troubleshooting section of the manual should tell you the location of the two adjustment nuts. Hope it works!
Great job. I want to install the same thing. But, in my case, the brackets probably cannot be positioned right on the studs behind the stucco+plywood wall. I am thinking to add a 2x4x12 ledger board on the wall and mount the brackets on the ledger board. I am not sure if it is going to work or not.
So this took me and my neighbour 5 hours to do. The instructions say use a 14mm drill bit, but found it wasn’t big enough so used a 16mm and the bolts fitted fine with a tiny bit of hammering. Plus instructions wasn’t clear on what to do with extra cord thing that you push down the fabric so just cut them off.
Hi, your video shows the screws you used to attach the awning to the wall. I want to know the exact size/manufacturer/vendor so that I can use the same screws. Thank you.
Yes. But you still have to make a guess from outside by drilling several small holes in a row. Good news is that the steel bar would be able to block the incorrect drill holes. Good luck!
Question, I'm having a difficult time find my size 8'x8' , I noticed you put 2 poles together. Is it possible I can buy a wider piece and trim it on the inside to size?
Thanks for showing this can be done solo. Great work!
Good video! I’m going to be installing mine. I bought a combo 12x10’ Awning. Thanks for the video. I saved it and sent myself a link.
All the best to your awning installation! May God bless your family!
Hi, I just finished installing my awning shade but i have not tightened everything down. When I opened the shade it slopes down too low around 45 degrees. how do I adjust so that the end is higher, like 10 degrees slope?
Easy, look for the two nuts that can adjust the slope on both sides of the bar. Loosen it, turn toward the directions of the wall, then tighten the nuts again. The troubleshooting section of the manual should tell you the location of the two adjustment nuts. Hope it works!
@@enderchoo ok. Thanks! I just did it.
The only issue I now is that the retractable arm does not retract evenly. I had to manually assist one of arms. I guess I get what I paid for.
Great job. I want to install the same thing. But, in my case, the brackets probably cannot be positioned right on the studs behind the stucco+plywood wall. I am thinking to add a 2x4x12 ledger board on the wall and mount the brackets on the ledger board. I am not sure if it is going to work or not.
My best friend, Enjoyed watching this video my friend Really awesome views Thank you Stay connected
Thank you! Are you currently working on this project?
So this took me and my neighbour 5 hours to do. The instructions say use a 14mm drill bit, but found it wasn’t big enough so used a 16mm and the bolts fitted fine with a tiny bit of hammering. Plus instructions wasn’t clear on what to do with extra cord thing that you push down the fabric so just cut them off.
You are right! This instruction manual is not elaborate and accurate. You just have to improvise a little bit. Good job!
Hi, your video shows the screws you used to attach the awning to the wall. I want to know the exact size/manufacturer/vendor so that I can use the same screws. Thank you.
I use a 4 inches concrete screw. However, I locate the wood stud in the wall and screw into it. I hope this helps!
The same color as mine. It's great in the summer!
Thank you .very helpful video.
Where can I buy this canopy?
beautiful 🙌👏👏👏👏👏
Thanks!
kha milega ye
Can this one be folded to cover the window?
Sounds interesting! Can you explain a little bit more about your idea?
I'm installing one for a customer next week. How many hours should I expect thos to take? Thanks for the video!
Around 5 hours. Make sure you get the right tools. Finding wood studs from the exterior wall take away big chunk of time. Good luck and God bless you!
I want it for car shed for Maruti Baleno Zeeta version
Not to bad of a video ? But don't you really think you should slow it down to about 90 Percent ?
Thanks
It’s a terrible video. There’s a lot they could if they want good reviews on the product. The written instructions with the awning also suck.
Thank you
How did u find the wood stud? Did you use a stud finder from inside the house?
Yes. But you still have to make a guess from outside by drilling several small holes in a row. Good news is that the steel bar would be able to block the incorrect drill holes. Good luck!
Does it hold water when rains?
No, it wouldn't
Is this good to install on a rented property? Is it easy to move or do you recommend something else?
Pretty easy to remove. You can take it down one piece at a time. Oneman show.
Nice video , how to install , Thank you
How can i get it ,a belongs to Tadepalligudem in India
My prob is the sagging at the middle then it will have water ponding
Nice tips but what went wrong those tops six holes on a brick too high I guess.
Yes, it was too high at the beginning. Also the anchor screw didn't hold well on the stucco wall. I used my own screw to attach to the wood stud.
wau grayt veedeeo! thenk yoo!
You are welcome!
In nepal where we can buy
Give me number please.
Mujhe leni h ye
Im from jharkhand
Maddening music.
Is this available in the Philippines?
Do you have Amazon in Philippines?
Gracias es de muy buena ayuda su video en estos momentos vamos armar uno
Como les quedó? Las instrucciones no son muy claras en algunas partes.
Como encontraron las maderas internas de 2×4?
where will I buy this item
Amazon
What may be the price ?
I need 3 each one size 10'X10' . I need water proof high quality sheet so that may be dually utilised Sun/rain roof.
This thing is pretty durable. It's been three years now.
Question, I'm having a difficult time find my size 8'x8' , I noticed you put 2 poles together. Is it possible I can buy a wider piece and trim it on the inside to size?
What is your current size? Let me see if there's a way to double the size.
@@enderchoo it's 8' wide by 8 ' length
How can I get in touch with this person or anyone to install my awning
Do you live in the Bay area?
Ill do it
@@P1985SD lol
You are on miami?
Northern California
好厉害!一个人干的,哈哈
What were the two brass looking things hanging from the the underneath the front part of the awning?At 9:37
Thank you for your question! I guess it is to prevent the extender from going too far when you retract the tarp. The instruction isn't clear enough.
Good work but Nasty music
Top pen não consigo conplar in kite desse
wow so many views
Didn’t show bolting of arms to front valance bar. Lousy
Annoyying f music.