Thank you for sharing this! The adjustment you make in the video, does it move the axle? Or does it move the electrical windings and their metal end pieces?
@@ricodaray Do you have advice for aligning my motor? It is like yours except on mine it seems the magnets rotate with the wheel, since they are not attached to the hub. - See my 3 second video showing by movement that the magnets are not mounted on the hub: drive.google.com/file/d/1gjjfRtq4dyWCbFRhLJNcOxfH6aYI3hcK/view?usp=share_link - See also my photo showing the problem place where there is no gap between the magnets and end bars on windings: drive.google.com/file/d/1gj5ZHEC0OGj_Nj3as7keoZTkOI3WV7BI/view?usp=share_link
@@anthonyengland422 , your magnets are on the wheel just like in this video but yours are clean and his are rusty. The stator will always touch the magnets when one cover is off because the bearing which holds the magnets away is not there to do its job. When you assemble the motor it’s important to ensure the mating surfaces between the wheel and the covers are perfectly clean with no debris that will prevent it from seating properly. If the cover doesn’t seat perfectly center, the bearing wont be perfect center, and the magnet can rub the stator. To fix this you can mount the motor in the swingarm and loosen the cover screws 1/2 turn, then grab the tire top and bottom and try to tilt the wheel left snd right until the covers find center, then retighten the screws and check that the wheel spins freely. You can reduce the chance of this by leaving the cover on the side without the cable tight and it will stay in the correct position. Then you only need to get the other cover centered during reassembly. Once you have it spinning freely there might still be a tiny misalignment that you can see in the wheel wobbling. You can also just slightly loosen the cover screws so that it can slide a little when you bump the tire with your fist, then run it and bump it until it runs true.
@Miguelvs It was really hard to move the wheel, like something was touching on the inside. It could have been some other thing IDK. I returned it and I bought a bafang with fat tires, to have some degree of suspension. Let's see how it goes.
Hello. If you hear like a grinding soung inside your motor. Maybe you need to replace the bearing. Then checknif there's a portion touching when you drive.
Hi friends, നല്ല രീതിയിൽ കുഴികൾ ഉള്ള റോഡ് ആണ് ഞങ്ങളുടേത്. Daily 40km ഓട്ടം ഉണ്ട്. . Hub motor കുഴികൾ ഉള്ള റോഡിൽ പണി തരുമോ എന്നൊരു പേടി... ഇതേ situationil hub motor ഉപയോഗിക്കുന്നവരുടെ അഭിപ്രായം പറയാമോ?????
Good morning po sir. Paano po dapat gawin sa hub po kasi po yung motor po kasi nakadikit yung isang side yung kabilang side po ay hindi kaya pag pinaandar po ay kumakayod po sa magnet? Sana po po matulungan nyo po ako.
Hello po. Nadikit po talaga yan pag walang takip. Malalaman monlang na hindi align pag iniikoto mo may kumakaskas sa loob. Tulad nyang ginawako matigas ikotin kahit wala naman kalawang
@@ricodaray Sir nakita ko po kasi na halos maupod po yung motor sa pagkayod sa magnet pag pinapaandar o ginagamit. Ang lakas din po ng vibration at halos pigil po ang andar.
@@ricodaray ano po kayang magandang gawin o pwede nyong i sggest para po maalign po yung motor? Kailangan po ba na malakas ang pag pukpok hanggang makuha po yung tamang alignment o dapat na pong palitan ng motor hub?
Sir sa mga nagtitinda at humagawa ng ebike. Mag join ka po sa fb group maraming parts at technicians dun. Ito yung link facebook.com/groups/1627522320896890/?ref=share
sir yung sakin misalign din binuksan ko kasi tapos nilinis ko yung kalawang then yung na assemble ko na na ayaw na umikot sobrang tigas, ginawa ko yung ginawa mo na ipukpok para ma pumantay, pero ayaw pa rin. 😢 nakaka iyak
@@ricodaray sir intersado ako jan sa nwow ars na may pedal pano po kaya yan gawin sir? need ko yan sir kasi kahit iupgrade ko nwow ars ko hirap talaga umahon sa ahon dito sa amin need ko yata ng pedal assist😞 naghanap ako ng video pano gawin yan wala akong makita
nice video marami ako matutunan dito tungkol sa ebike..
Salamat sir
Thanks ang galing ng diskarte at technique.
Salamat sir😊
Thanks for showing me how to repair it
Welcome
amazing, you made it looks very easy
Thank you sir🙂
Thank you for sharing this!
The adjustment you make in the video, does it move the axle? Or does it move the electrical windings and their metal end pieces?
There is no movement happened, only push the edge of stator to align with the magnet.
@@ricodaray Do you have advice for aligning my motor? It is like yours except on mine it seems the magnets rotate with the wheel, since they are not attached to the hub.
- See my 3 second video showing by movement that the magnets are not mounted on the hub:
drive.google.com/file/d/1gjjfRtq4dyWCbFRhLJNcOxfH6aYI3hcK/view?usp=share_link
- See also my photo showing the problem place where there is no gap between the magnets and end bars on windings:
drive.google.com/file/d/1gj5ZHEC0OGj_Nj3as7keoZTkOI3WV7BI/view?usp=share_link
@@anthonyengland422 , your magnets are on the wheel just like in this video but yours are clean and his are rusty.
The stator will always touch the magnets when one cover is off because the bearing which holds the magnets away is not there to do its job.
When you assemble the motor it’s important to ensure the mating surfaces between the wheel and the covers are perfectly clean with no debris that will prevent it from seating properly. If the cover doesn’t seat perfectly center, the bearing wont be perfect center, and the magnet can rub the stator.
To fix this you can mount the motor in the swingarm and loosen the cover screws 1/2 turn, then grab the tire top and bottom and try to tilt the wheel left snd right until the covers find center, then retighten the screws and check that the wheel spins freely.
You can reduce the chance of this by leaving the cover on the side without the cable tight and it will stay in the correct position. Then you only need to get the other cover centered during reassembly.
Once you have it spinning freely there might still be a tiny misalignment that you can see in the wheel wobbling. You can also just slightly loosen the cover screws so that it can slide a little when you bump the tire with your fist, then run it and bump it until it runs true.
@@imho7250 Thank you!
Did this work?
Naku pag may nag loko sa e bike nmin soon eto makakatulong... Sa mechanic, ipapanood ko nlng s knila. 😊 Ayoko magkalikot, bahala cla.
Hahahaa dito lang po ako, PM is the key😁😁😁
wow! ganyan lang pala sir. tnx for sharing po
youre the only person ive seen on the internet doing this. is there any other videos or "how to's" to align a hub motor?
Thank you sir, i didn't see other doing like this. Align hub motor without using special tools.
Full watched. Salamat for this tip..
Amazing Friend 👌🏿👌🏿👌🏿
Thank you friend 🙏🙏
Ang galing naman po gumawa ng mga sasakyan
boss tanong ko lng po kung pwd ba masira ang controler ng Epedecab sa kadahilanan na putol yung wire ng trottle sa motor hubs?
Yes sir. Kahit isang wire maputol sa throttle at hub dina tatakbo
Thanks a lots bro
Thank you😊
i have same issues with my bike i going to try tomorrow
atleast now i know! salamat po
Need po natin to pag may e-bike na tyu. 😁
@@PartridgeTV onga pala wala pa pala tayo Ebike haha
Say goodbye to the threads on that axle.
Axle is stronger than cement and the treads still good.
Kawawa yung threads😢. Walang sapin kahit na matibay , magkakaron ng little damage. Improper disassembly.
Boss may video ka ng paano mag aign ng minebela at gulong
Na bunggo kaba sir
If nabangga ka pakit front shock or pa align mo sa machine shop para mag ok manebila mo sir
Lods, size ba ng rim nyan 2x12?
Saan po kaya makakabili nyang rim na yan na rim lang po, di kasama yung loob nya?
Ty lods...😊
Size nyan sir 14 kasya pa mio na gulong. Sa nwow po yan sir
Boss pwide poba sayo ko pa wiring paaayus motor Foldy E-bike ko take care
Dito ako sa Davao sir
pa request sir waterproofing ng hub motor hehe
Dude! Use block of wood when pressing out that motor. You're damaging that axle. 😳 That was painful to watch
Thank you sir
Saan po shop niyo pa align din ako ng kaabo mantis pro SE ko?, April pa available yung hub nakakaiyak
Sir wala po ako shop, employee po ako ni nwow. Dito po ako ngayun say mindanao
thanks sa idea cling tv
Boss ano po kaya pwedeng problem kapag laging umiinit yung phase wire ng hub yung 3 wires po hindi naman po loaded
Weak na yung wire sir. Putolin mo yung sunong na portion at dugtonggan or lagyan me ng bagong terminal. Make sure na mahigpit
Agila crisostomo gud day sir tnong lang saan po ba nakakabili ng brushless controller tester
Multi tester/ multimeter lang po gamit ko. Meron sa mag electronic store or sa lazada meron din
Thank you for sharing po.
taga saan po kayu sir??
naaayos pa po ba yung magneto ng hub?? Romai Nova
Sir dito po ako sa davao city. Mag join ka po sa fb group maraming technicians dun. Ito yung link sir
facebook.com/groups/1627522320896890/?ref=share
Sir ano b problima nebike ko kahit saglit lng ginamit sobra init ang puse
Linisin or higpitannyung holder ngnfuse sir. Pwede monrin taasan ampere nang fuse
Bakit nawala sa Balance yan sir, thank you sa Info, check mamaya hub ko
nangyayari yan pag kinalawang an yung loob kaya pagka tulak para ma buksan ay na deformed yung laman
Woah the quality control of these things are... inexistent. This happened literally on my second ride.
Good afternoon, how did you knew that the hub was misaligned? Did it make any sound? Did the motor started to break when you were riding?
@Miguelvs It was really hard to move the wheel, like something was touching on the inside. It could have been some other thing IDK.
I returned it and I bought a bafang with fat tires, to have some degree of suspension. Let's see how it goes.
Hello. If you hear like a grinding soung inside your motor. Maybe you need to replace the bearing. Then checknif there's a portion touching when you drive.
PRIMITIVE TECHNOLOGY....
:V
Basic DIY on how to fix motor without using any expensive tools or machine
sir anung sukat ng screw ng mga motorhub na 10' ,,anu tawag m5 m6? no idea kasi thanks
Hello po, mostly allen bolt po yung naka kabit 4mm
Hi friends, നല്ല രീതിയിൽ കുഴികൾ ഉള്ള റോഡ് ആണ് ഞങ്ങളുടേത്. Daily 40km ഓട്ടം ഉണ്ട്. . Hub motor കുഴികൾ ഉള്ള റോഡിൽ പണി തരുമോ എന്നൊരു പേടി... ഇതേ situationil hub motor ഉപയോഗിക്കുന്നവരുടെ അഭിപ്രായം പറയാമോ?????
Good morning po sir. Paano po dapat gawin sa hub po kasi po yung motor po kasi nakadikit yung isang side yung kabilang side po ay hindi kaya pag pinaandar po ay kumakayod po sa magnet? Sana po po matulungan nyo po ako.
Hello po. Nadikit po talaga yan pag walang takip. Malalaman monlang na hindi align pag iniikoto mo may kumakaskas sa loob. Tulad nyang ginawako matigas ikotin kahit wala naman kalawang
@@ricodaray Sir nakita ko po kasi na halos maupod po yung motor sa pagkayod sa magnet pag pinapaandar o ginagamit. Ang lakas din po ng vibration at halos pigil po ang andar.
@@ricodaray ano po kayang magandang gawin o pwede nyong i sggest para po maalign po yung motor? Kailangan po ba na malakas ang pag pukpok hanggang makuha po yung tamang alignment o dapat na pong palitan ng motor hub?
It's not a ebike it's a electric scooter 😂😂😂
Saan po makabili ng hub motor kung sira na po talaga???
Sir sa mga nagtitinda at humagawa ng ebike. Mag join ka po sa fb group maraming parts at technicians dun. Ito yung link
facebook.com/groups/1627522320896890/?ref=share
sir pwede po request 2 controller 2 hubs dynamo in 1 throttle how to connect plus the dis/advantage thanks
sir ano po ba tawag dun sa sealant anong tamang pangalan
Gasket maker po sir
s.lazada.com.ph/s.2fEy3
Pano pag maluwag na shafting
sir yung sakin misalign din binuksan ko kasi tapos nilinis ko yung kalawang then yung na assemble ko na na ayaw na umikot sobrang tigas, ginawa ko yung ginawa mo na ipukpok para ma pumantay, pero ayaw pa rin. 😢 nakaka iyak
Same here😅
Bravo peccato che devo tradurre però dopo un po' ho capito quello che stavi facendo un saluto
Hello my friend, I'm sorry but i dont understand what you say, if you have some to ask please say it in english. Thank you and godbless
sir bakit po may gear yan sa hub?
Sprocket po yan sir kasi di pidal po yan
parang sa nwow ars po yan sir no tapos di pedal?
@@gianskie1566 opo sir
@@ricodaray sir intersado ako jan sa nwow ars na may pedal pano po kaya yan gawin sir? need ko yan sir kasi kahit iupgrade ko nwow ars ko hirap talaga umahon sa ahon dito sa amin need ko yata ng pedal assist😞 naghanap ako ng video pano gawin yan wala akong makita
Sir bakit hirap baklasin Yong break shoe sa likod
Pag matagal di nabaklas at kinalawang matigas tanggalinnyung brake hub. Try mo spray ng wd40 sir tas pokpokin mo dahan dahan
@@ricodaray Yong takip po NG break shoe ayaw matangal po eh prang my naka bara
lodi