Hey Mark, it seems you have misunderstood the correct situation to use the different settings. To start, I am referring to my own personal settings that I find best for my typical long range flight situation. I assume you are thinking that if I lose connection at the top of the mountain and the drone goes to whatever the max altitude was that it should get high enough to recover signal. In such a scenario that would be correct. But now with the same settings a different scenario, I'm on my way back down the mountain everything is going fine, I'm most of the way back now and decide to go and check out a waterfall that I pass near. But now I fly behind a ridge between myself and the drone, if I activate GPS rescue in max alt mode it will continue to gain altitude until I get signal back and turn rescue mode off myself. Again you're right for this scenario it works. But now lets stop thinking about only ourselves and dealing with an easily managed scenario. Drones are not 100% perfect they have bugs in firmware and the electronics are only consumer grade not aviation or military grade components. So say your goggle battery dies, or your FPV camera hits a branch and gets broken, or your crossfire antenna is damaged and you didn't notice. In all of these situations you will not be able to regain control of the drone and it will carry out the MAX ALTITUDE rescue mode. So I just flew up a 2.5km tall mountain and this happens close to home, so to start my drone will try to ascend 2.5km all at once, I fly with li-ion so it would never get up there it would kill the battery halfway up, die and drop. Say it has a half full lipo on board, ok so it doesn't drop it goes the whole 2.5km up but now its over top of me not the mountain so its literally 2.5km up in the air. That is absolutely not acceptable practice. This scenario would endanger full size aircraft and would be very irresponsible. Getting your drone back is not more important then making sure to stay out of the airspace of commercial aviation. Current altitude will work for most situations. It can be set to go to a certain number of meters above current altitude, 50 or 100 meters would be a good setting if you're really worried about it not going high enough. With proper route planning done pre flight you should never need to use max alt rescue setting. Its purpose is for people that are NOT flying up mountains, like following a river for 2km out and you lose signal, then max alt would be safe in all situations. That's why it's an option because no one setting is CORRECT for every situation. As well I am making a RUclips video that will be watched by thousands of people. It would be irresponsible for me to just tell everyone to use a potentially dangerous GPS rescue setting. Commercial aviation safety MUST ALWAYS be the first thought in long range flights, nothing else is acceptable.
I'm the only one among my FPV friends that has angle mode enabled for panic scenarios. I used to practice the muscle memory for hitting it regularly. It's saved me so many times, especially when getting stomped out by a nub plugging in without warning. Never understood why folks don't set it up. On another note, might be a good idea to make a LR fundamentals series. Things like flight planning, preflight check, battery level management, failsafe plan(s), etc. At the very least introduce people to things to consider beforehand.
That's a great idea. I am planning on doing more long range flights with in flight narration as I'm flying (another camera on me and my spotter). I have a couple of videos already made that will be getting posted soon that touch on this concept. I've been thinking about a pre flight planning video, actually even tried recording a couple of them. (I still have a video to do about losing a quad several months ago. I've been avoiding it because I feel a bit silly about how it happened. It was my first try at flying long range and talking to the camera at the same time. I got distracted by talking to the camera and my spotter got distracted by trying to think of helpful questions from a viewers perspective and we were both also distracted by what gopro shot to try getting next. In the end we both realized how low my battery was when it was too late! When I eventually get that video done it will have a few good lessons in it.)
to put it simply if it wasn't for this video I would have lost my quad three days ago because I did put it in angle mode and I did hit the throttle up and it did work because my goggles went dark but this gave me time to reconnect the goggles to the VTX I can never think this guy enough surfing CPA Hawaii
Alot of ppl dont actually know about how you can use both angle and GPS mode to get out of a bad situation, so this tip is a good one!.. of course I like to see more of the actual flight characteristics in real world situations. If you got more flight footage of these things, that would be entertaining!... thank you for your content.
Thanks. That brings to mind a good video idea. I have a lot of footage where I go through temporary video loss. It often happens multiple times over a day of long range flights. I should do a compilation of short clips of losing video and how I handle it. It would be a good follow up video.
I am almost sure that on Betaflight when the GPS Rescue is activated the Angle Model is selected automatically. After my first drone lost in long-range, I learned some things: (i) use powered beep; (ii) display and record the GPS coordinates on DVR goggles (never go flight without record is on); (iii) save automatically on the radio the flight log with GPS coordinates.
I started using angle on a switch when you recommended it awhile back. Very good advice I like to throw in angle and use yaw if needed to get signal back don't have to worry I'm upside down.
Can we make a switch in OpenTx which when hit - it automatically turns on Angle mode, rises throttle level a little bit higher than hovering level and adds a little bit yaw rotation?
@@edgafpv its the same setting as you have for sure for arm switch. just add in mixes next switch, go to betaflight, try if you get signal from your radio and add angle mode in bf.
@@edgafpv it may be possible watch one of the bard well videos regarding throttle curve altered by switch… I would suggest you just stick to using the throttle manually
This is the best video on how to setup gps rescue! I did try out gps rescue on my new quad and followed the steps from your experience. Worked exactly as expected 👍
I've become very comfortable with fixed wing inav rth on failsafe since I live in the city and get fail-safes with csrf @1w well within the 5.8 video due to interference. I've found with quads I trust inav gps way more than betaflight but tuning is like betaflight was 4+ years ago, a headache. But I like that my home arrow points home and rth actually flys home Everytime.
Yes exactly, it's too bad we have to choose between good GPS function and good flight characteristics. But it's understandable, one firmware won't be great at everything. It's crazy how amazing the dev's get these things flying though.
@@FalconRadFPV ya, I always have to check myself before complaining about open source stuff if done nothing to contribute to. It's like complaining about trail conditions when you haven't lifted a finger to do any work.
This is an incredibly helpful and underrated video. Thank you so much for putting the time and effort into showing others, greatly appreciated. This video just got you a new patreon 👌🏻
@@FalconRadFPV this format was awesome. I usually fly angle anyway because I’m not very good. Thus video takes the mystery out of your recoveries. There weren’t as many differences to my settings as I would have thought, but you have made me more curious about reading the betaflight wiki and educating myself
Finally a great video that explains all very good not like others. I just soldered today GPS to my Protek35. I do it because i fly in mountains where is many cell towers and had 3 rxlosses and my quad crashed. Hope GPS Rescue help me in situation like that when i lose rc link conection. Thx for great video. Tomorrow must test how it works :D
@@FalconRadFPV Im really happy with results. GPS Rescue works very well. I switched off my radio, done 3 failsafes and more. This thing for sure will rescue my quad. But im not sure about angle settings in bf. I used 35 and it work good. But in high mountains sometimes wind is 30-40km/h so maybe raise angle to 40?
settings are ok but i would add that if you are flying over terrain that is deserted it would be preferable to turn off sanity checks they will drop your quad out of the sky for all sorts of silly reasons. I would also turn off stage 1 failsafe or just reduce the delay to zero. On defaults the radio will have its own guard time and then betaflight will have a time where it just holds does nothing or even worse drop throttle before initiating gps rescue. Ideally you want gps rescue turning on as soon as the receiver indicates failsafe. I have had gps rescue save my drone from crashes when i got a short failsafes as i was diving at the ground. The downside of not turning off sanity checks is that you might burn an esc if the drone crashes near you on rescue as it wont switch off the motors but its better than dropping out of the sky over a mountain because the gps module had a hiccup or you have a desync and it decides you collided with something and disarms the drone. I wish they would add loiter mode to gps rescue as i do believe its much better a drone loiter until the battery is depleted than it crash with full power face blenders at its disposal.
Thanks for the comment. That's a good point you make about the delay of guard time. I think it shouldn't be 0 though. You don't want it kicking in all of a sudden because of a micro failsafe. Which are more common at longer ranges I think. I can't have sanity checks off where I live, well in the summer time at least, the chance of a fire is too great. I turn sanity checks off for everything except failsafes.
@@FalconRadFPV the radio system itself normally has a guard time but this is something you can test on the bench. I would rather set current limit on esc's rather than sanity checks ever be enabled if your worried about starting fires.
It’s possible to set a switch position that triggers failsafe. This is a good way to test the behaviour when having a failsafe without actually having to turn off the tx or force a failsafe by flying behind something or miles away.
yes under the modes tab you can put failsafe on a switch to test it, after you're comfortable remove it and switch it back to gps rescue, turning off the TX is really unsafe so this mode was designed to simulate that without having to turn off the TX
I saw this right before my maiden flight this morning and I should have watched it. I have rescue set up on my other 7" and it has save me a few time so I want it working on my Falcon 7 as well. On my second short flight I decided to flip my rescue switch to test it out and the quad tumbled out of the sky, luckily I test at low altitude. Can't seem to figure out what the difference is between my 2 set ups where one works and the other doesn't. Now I watch this video and see how you have it set up.
If you you flipped the switch and it just dropped then my guess would be that it failed the sanity checks. If you continue to have trouble with it you could try looking at what the blackbox says. Maybe there's a gps rescue status debug mode? Read the betaflight wiki, gps rescue section. There is a part on the sanity checks and what they are. You may want to set your sanity checks to failsafe only, just be careful when you use it and know what the different sanity check settings do. It's explained well in the wiki. There's a link in the video description to the GPS rescue page of the wiki.
@@FalconRadFPV I was thinking that was well and I thought it was possible I was too close. I changed the setting to 50 meters and it still responded oddly. I have to really look at it.
The remark about hitting disarm instead of rescue rings hard for me. I'm interested in long range coming from Freestyle, where you keep a finger on your arming switch basically the whole time. Could easily see myself reflexively disarming from a video loss... Thanks for the vid.
Excellent tutorial, I'm using it for my first long range flights! I wonder if using Li-ion batteries it is necessary to decrease the rate of ascent and ground speed, because they are batteries with lower discharge rates than Li-Po ones (mine is a Li-ion GNB 4000mah 10C). What do you think?
Man this is a GREAT video. Absolute nr.1 for GPS. I actually use the switches identically as you, just don't have angle+gps. What's the difference if there is only gps rescue? it goes into angle mode as-is.
Angle mode doesn't have to overlap gps rescue, but it's good to switch from rescue to angle mode then back to full control. It can help to avoid control issues as switching out of rescue mode.
Love your videos! Keep up the great work. Just ordered ur frame from the CNC place and brother hobby motors from. Rotor Village... Can't wait to build a nice 7in long range. Be a great addition to my 6in long range. Again, thanks so much for being so great about showing how u do what u do and how. 😁👍
Hi there, I've got a Source One 7 inch with HGLRC M80 Pro GPS and Zeus F722 stack in it with 2807 1700kv Emax ECO motors. The quad flies great and I've even thought of putting a 6s battery on it with a 70% throttle limit. However... GPS rescue... thats the last hurdle I can't seem to figure out. When I trigger gps rescue the quad will shoot up into the air and keep gaining altitude and in most cases also go off in a direction that is not "home". The home distance is always displayed correctly. I've tried betaflight 4.2, 4.3 and even 4.4... My throttle hover is set to 1250, my acend rate 3m/s and altitude mode is set to current altitude... I've tried 2x different Zeuse stacks (one with the BMI270 and the other with the MPU6000) both do the same thing. Before I put a 3rd flight controller in there (thinking of a Holybro F7 or a Mamba f405), I'm hoping you might have seen something like this before and could steer me into the right direction. All my other 5 inch quads have gps units (5x quads) and their gps rescure works just fine...
I would suggest trying to swap out the GPS for a different brand, or it could be the GPS settings. Have you tried GPS rescue with leaving all the settings on default, or as many settings on default as possible, but try to do it with everything on defaults. In very rare cases even a GPS setting can cause a hidden/unknown conflict or firmware issue. If it works fine on all defaults, then change each setting one at a time and test, until one of them causes the issue you described. But if you've tried two different stacks, I'd suggest trying a different GPS next.
@@FalconRadFPV thx for the reply.. Different stacks but same hglrc F722. One with Bmi270 a d and one with mpu6000. Still can try my mamba f405 stack. I've tried it all on defaults. I've also gone and changed one at a time... Results of my other quads and in the video also this 7 inch where you can see the issue : ruclips.net/video/gGBFUM1Q6bM/видео.html
Maybe you have a magnetometer (compass) on the GPS module or in the FC. It's recommended to not use them unless you can keep it far away from any other wires and electronics (10 cm minimum, which is not possible on most quads). The compass might show into the wrong direction because of interference. Also the orientation might be set up incorrectly in Betaflight. You should check the manual of your FC and GPS to set their orientation accordingly. A magnetometer has a separate orientation setting. Also check that it's all installed with the arrow facing forward.
In the failsafe procedure, you can choose drop or GPS rescue. In case of a broken receiver, the drone will drop or will fly back with GPS rescue. Since you cannot control the drone anymore with GPS rescue, I wouldn't want to be where there are buildings or people. My guess is that you better have your drone dropped, except when you are flying in the woods and mountains, like you are doing. Am I correct?
Yes that's right. When near buildings, vehicles or random people walking around then it's best to set it to drop. I always fly long range 20 or 30 km from the nearest buildings with very few people around.
Hi, i just tried gps rescue by switch for few times (BF v4.3.2), and i tried to fly my quad toward away from me (i face to east and i fly my quad to east too) and around 200m from Home Point, i turn on gps rescue switch, the quad suddenly turn 180deg and face to my position (which is good) and going up but why it flew far away from me? lol, so i turn off gps rescue switch and regain control. I set angle to 35, altitude mode= maximum, sanity check= failsafe only, initial altitude= 100m, minimum distance= 50 and others values are default value. thanks, subbed your RUclips channel.
Great video, thanks! I've just set up my Matek M8Q-5883 GPS, and all seems to be working except the home arrow; It doesn't point home, but the home distance is correct, I've tried uploading the font with the battery attached, and it still doesn't work. I was wondering if my tests need to be further from home to work. I've been flying 200m in a park on tests; the arrow is the wrong way or pointing to the side. I am nervous about flying far until I get this sorted. Thanks!
It's happened to me a few times, somehow it usually sorts it's self out if I fly over top of myself at the home point. That hasn't happened to me in months now though.
They are usually plagued with interference on quads. You might be able to place them somewhere on a fixed wing or very large quad where it has no interference from electrical components and wires, but usually it's better to use GPS for orientation. That requires flying away from the home point in a straight line for some distance (30-50 m should be fine) so Betaflight can get the direction right.
The setup should still be quite similar although 4.4 has a few more options than 4.2 did. As always, and especially with GPS rescue, stick to changing things that you understand the effect of and do more than one test of the setup before relying on it to save you.
Nice, just take it slow and don't go too far right away. A couple tips: Get to know what mah count (OSD mAh used) you get with each battery. Go 1 km out and back a bunch of times, to get an idea of total distance and flight times. Then always turn around and come home when you are 40% of the way through the total mAh count you are expecting for that pack.
Regarding the 3 pos switch, why do you have angle mode in the 2nd _and_ 3rd position? Won't GPS Rescue take over on the 3rd position anyway? I.e. wouldn't it be enough to have angle mode only on 2nd position? What are the benefits of having angle mode and GPS rescue at the same time?
The though is that the FC is always in angle mode when changing between the two end positions. I've heard of instabilities when changing out of GPS rescue mode. It doesn't hurt having angle mode go all the way over. I believe that if it does not that the quad when gps rescue is turned off would leave angle mode (part of gps rescue) then switch back into angle mode again right afterwards. It just seems reasonable to have it stay in that mode rather than exit and reenter it right away. In blackbox logs you can see that this process is actually quite rough unless you have the settings toned down in which case the gps rescue response is slowed and increases the risk of gps rescue crashing your quad.
Thanks for ur sharing.. It was great. I wanna ask u about failsafe setting. In menu failsafe switch choose stage 1 and stage 2 chose a gps. In failsafe switch why u use stage 1.
Stage one is a hold time between losing signal and activating gps rescue. This is so that if signal is lost for less than 1/2 a second it won't activate rescue mode unnecessarily.
@@FalconRadFPV so the gps it's ok right. Idont have to change the failsafe switch to stage 2. What is the difference when I choose the stage 2. Not stage 1.
Hi . I really like your videos. What do you think about betaflight vs INAV. You are not using the inav configurator. Why not ? Is Betaflig better? Obsession ?
I just like the way it tunes and flys with betaflight. I also don't feel the need for the automated stuff in INAV. That said, INAV has far superior GPS functions. The return to home works better, and it has stuff like hover in place and automated flight with way points and more. I just want to fly my quad up a mountain and keep it simple.
Great tips and video again. Totally agree with your recommendations.Thks for sharing. Off topic..was wondering if you have checked out sharkbyte vs analog. Very promising...I have been testing SB for LR.
Thanks. Interesting about sharkbyte. I was thought it may not have the necessary output power. I remember seeing a thumbnail for a sharkbyte video you did, I'll have to check it out!
@@FalconRadFPV the necessary power for LR is exactly what I've been testing. So far have been out 2 miles and I think one can push it further. A newer higher powered vtx is rumored to be in development.
Thanks for the video and tutorial. Am i correct the aux 3 switches between acro-angle-angle gps mode? When losing video signal do you switch the aux 3 to gps mode or does the fc go into failsafe gps mode. And when regaining video signal i would guess you make the switch out af gos mode and into pure angle mode. Thanks
I like to switch to angle mode and just throttle up to regain video rather than counting on GPS rescue. If that doesn't work I flick the switch alll the way to the end to engage GPS rescue. If your drone failsafes it is best to switch into GPS Rescue mode until your video returns and then switch back to acro and retake control. This is because in odd cases of failsafe the drone could regain connection to the TX and return control to you even though video is still out so you want to make sure it stays in GPS rescue mode until you are fully ready to retake control.
When engaging angle mode, what do you think about pulling the pitch back a little while increasing the throttle? I realize this slows forward momentum while bringing the quad up faster.
If you are comfortable giving the stick inputs with no video then, yes! I actually do exactly that pull back on pitch and increase the throttle, I'll often do just that and skip activating GPS rescue.
one more thing, so thankfull, that you taking time to answer, is it true that if a failsafe happens, and GPS Rescue gets automatically on, i have also to switch my AUX GPS Rescue on, because the quad will fall if i dont have turned the switch on? Oscar Liang has explained it like that and that makes me a bit confused, why it should drop as soon as i have RC Signal back?? i share the exakt part in a comment below
Oscar Liang: "Activate Failsafe mode. Now the quad should enter GPS Rescue mode. You should also activate Rescue mode now, as I mentioned earlier. When you get out of Failsafe, you can manually disengage Rescue mode and that gives you enough time to take back control, otherwise it would just drop to the ground."
Sorry I don't understand the question. I find the 3 position switch setup that I cover in this video is the best way to do it. I think he is talking about when you turn rescue mode off you have to move the sticks enough to let the FC know that you have taken back control. Just use the 3 position switch setup, it should prevent a fall out of the sky scenario.
Great video thank you!!! I am still a beginner in the field of FPV, but I have already collected a few hours, simulator and outside. Now I wanted to ask how I can extend the frequency or the range of my drone? (Law of the drone does not matter ;) ) Feeling 30 meters I can fly and the image is already bad in my FPV glasses and can no longer control the drone practically. What exactly do I have to set in Betaflight so that I can fly further? My equipment Protek 35 DJI Goggles V2 DJI FPV Remote Controller V2 Greetings from Switzerland
Hi FalconRad thanks for all your work. I’m using gps for the first time on my quad and set it up like you show in the video. Everything seems to work fine but sometimes mid flight e lose gps signal but after a few seconds i get it back. The number of sats seems to be stable before and after the signal loss. Do you know what might be the problem? Thanks
Nice flying sir, are you running dynamic mode on the crossfire module or locked at 50hz? Also what power output? I’m having some issues with dynamic and latency while jumping from mode 2. To mode 1
I just leave it on dynamic but I'm thinking about switching to locking it at 150 once I start doing more long range and less field testing in the spring. I use 500mW usually for power output.
The crossfire receiver should have the failsafe setting set to "cut". This will halt all signals in the event of a failsafe so the FC will realize it's a failsafe situation.
@@FalconRadFPV Finally complete my AOS falcon 7 build..it flew exceptionally well with the stock pid and filter setting..Have question with the GPS rescue. I noticed the quad drop in altitude after the GPS rescue initiation before its picking up the altitude in the next seconds. Is that a normal behaviour? Settings are as per your recommendation in the video.
Thanks for this Falcon! I've copied your settings but in betaflight modes settings I don't see the gps rescue turn yellow when I arm the switch. is that to be expected or am I missing a step somewhere?
Not sure, as long as you set it for aux XX and then you can see aux XX move in the transmitter tab when you flick the switch, then it should work as long it passes the sanity checks.
I am surprised you dont use iNAV.. I have BF on my 5" LR but my 7/8" LR has iNAV which not going to lie I do have 2 locations the compass gets thrown off though i didnt check the 5" there to see if it affects GPS at all Also I set my speed to 35mph just cause in testing I think that was allowing the drone to cover the most distance per battery mah. Granted changes with motors and props being used. Other thing I bring an extra battery to plug in and just fly around or idle waiting to get a lot of satellites. I usually wait for 10. I have a transmitter call out for over 10 satellites. one also for 5 if im impatient I dont like my angle switch with GPS rescue just cause i use angle sometimes to just hover a secend doing something. and i dont want to accidentally hit gps rescue. but i do try to remember to hit angle when i lose video also before going to GPS rescue
Honestly I'm not keen on learning new firmware, so I just keep using betaflight instead of inav. Although I might have to get around to learning inav at least for the position hold and way points.
hihi hoho haha hihi hoho .. 1:40 when you accidentaly hit the disarm switch .. lol hohohahah hihi ... happened to me lol hoho. Darwin-price goes to me :) So I put some soft-tape around that arm/disarm switch so I can feel, it's a special switch, and I make sure, I have no switch near there, what I would ever have to use on a flight. (especially the one just above the arm/disarm switch .. on that I have the vtx-on/off for now .. now until I figure out a better solution)
can't see details of what you show on betaflight on my laptop. everything is so small. this video would need to be viewed on a large screen TV to see what you are doing.
i have two quads with GPS , a 5 inch with BF 4.2.0 and a 7 with 4.3.6 do you think this settings will work for both? i really dont wanna change my firmwars. thanks. cool channel sub
The main settings should work for both, although I do not have any experience with BF 4.3. I'm waiting for it to get the bugs fixed and the final release before I start using it. I have noticed that BF 4.1.7 has a much more responsive GPS rescue mode. I wish BF 4.2 GPS rescue worked as well, it starts off really slowly losing altitude before kicking in properly.
@@FalconRadFPV yes , i did some tests com my quds , 7inch 4.3.6 and 4.2.0 , th gps activates super fast , but it takes more time to start reacting comparad to your videos. but it works.
@@FalconRadFPV but i think its okay for now . iam goint nowehre far like you. ill be mostly at 1.5 mile away. i was flying withou GPS on DJI Radio for the last year and a half. Now iam on crossfire and with GPS , gonna risk a little more. thanks for sharing your experience
There is no issue that I know of to do with the XT60. I've built this quad with the xt60 coming out the side, front and back. I'm using all the original TPU parts with no issues at all.
@@FalconRadFPV ok. The xt60 fits into the rectangular cut out on the tpu just below the falcon head . I assumed the xt60 fit there. I'll gladly secure the xt60 leads out the side. Thank you. Love the frame
hi , I have a question for you, how you make for configuration the altitude, yuo used barometer or gps or let default into the CLI, you can help me please thanks, this video is very interesting
The GPS will estimate the altitude, but if you have a barometer you can enable it in the configuration tab of betaflight. A barometer will help the flight controller to more accurately estimate the current altitude. No CLI needed for any altitude or barometer settings. Just the checkbox for barometer along with magnetometer and accelerometer in the config tab.
Yes I have, It's a common question in the comments. I'm comfortable with betaflight so I just stick to using it. It's probably time that I get an INAV quad setup though. I'm sure I could find some interesting uses for the extra features.
It depends on what your doing. Sometimes it uses a SET command and sometimes it doesn't (like with resources I think). If you want you can email me at falconradfpv@gmail.com and I'll help you out with some screen grabs + instructions or something like that.
I'm assuming GPS Rescue just kicks into action all on its own, right? Or am I totally off base here? 'Cause if it does, why the heck is there a button for it? I mean, what's the deal with that button if GPS Rescue is just doing its thing automatically, you know? It's like, "Hey, button, why you here if you ain't got no job to do?" :) I'm kinda confused about that, man.
It does kick in automatically, but only if the connection to the transmitter (joystick) is lost. The video connection is a completely separate thing. If my video connection goes down (can't see where the drone is going) then I will use the switch to activate gps rescue so that I don't have to fly the drone with no video (blind).
Gotta confess, it never crossed my mind, probably 'cause I've been rocking the DJI FPV setup, and that feature's not in the cards. Thanks for dropping that knowledge. I know I'm hitting you up with questions, but I'm gearing up to explore the long-range scene. I'm itching to pick up some insights, and this one's been elusive - how's the VIDEO signal rollin' with DJI Goggles 2 and DJI O3 Air Unit? Planning to soar with the iFlight Chimera Pro V2, RC Commando 8 (ELRS 918 MHz, 1W).@@FalconRadFPV
PLEASE JUST TAKE SHORT SEC: WHY the quad always drops at first till it rescues? if i get a failsafe close to gound (in dives or whatever in the mountains) my quad will still be lost even with GPS Rescue...i tested it, i always have to be like 20-30m off the ground, because if i am lower, the quad smashes the ground before gps rescue gets into it.... i will sent a paypal tip for you thanks so much
In the video I am using BF 4.1.7 GPS rescue is much faster and responsive in BF 4.1.7 I do fly BF 4.2 now but as you say the response in 4.2 is basically useless. I suggest practicing using the switch setup that I cover in the video so you can use auto level, throttle up, then engage rescue mode. I have thought several times about going back to BF 4.1.7 because of how bad BF 4.2 rescue mode is.
@@FalconRadFPV thank you so much, my biggest Problem is, firstly, BF 4.3 flys untuned soo freaking good and i cant tune my quads sadly, i dont get it to the point of a really good flying quad mostly. secondly only in BF 4.3 i can see RSSI / LQ in DJI Goggles, thats sooo stupid....so i have to choose between a good flying quad and RSSI/LQ displaying or BF 4.1.7 for a good GPS Rescue....thank you so much for your information, what i dont get is, why they made GPS Rescue worse in a newer firmware, cant imagine, that this is a typical "bug"...is it official information your just your personal experience?
@@FalconRadFPV ijust set my yaw to 100 in cli, yes i experience quad drift a little bit when hit rth, thats scary, and i see you explain how to manage the quad when hit the rth, immediately fast yaw and push very quickly thats important ^_^ thanks
I'm not sure if I'm understanding your question. You can change it as a setting, under "sanity checks" in the failsafe tab. WARNING turning sanity checks off can start fires!!! I've heard of quads hitting the ground and going full throttle with no sanity checks. I have sanity checks set to "failsafe only". So if I hit the switch to engage gps rescue mode it will bypass the sanity checks (risky know what you are doing!) but in the case of a failsafe it will still do sanity checks. READ THE BETAFLIGHT WIKI for gps rescue, read about the sanity checks.
I don't understand the logic behind having a combo of Angle and GPS Rescue. Isn't GPS rescue an autonomous mode? Isn't GPS rescue a self level mode in a way?
Yes that's right. Although, if you are near the ground and have trees to your left with open space on the right, then lose video. Do you engage angle mode, roll right a little and throttle up for a couple of seconds until you are clear of tree tops and then switch to gps rescue? OR just switch to gps rescue right away and cross you fingers and hope that it stays away from the trees? If you are new to long range then straight to gps rescue may be the right choice. If you are an experienced pilot with the right setup and you have practiced this method in can increase the chances of getting your quad and GoPro back safely. Also I've heard of people having control issues after switching out of gps rescue, it's always been fine for me, but going into angle mode on your way out of gps rescue should increase the chances of a smooth transition back to piloted flight.
@@FalconRadFPV I completely agree that the three position switch should have angle before the GPS rescue. It's a very logical step. And I'm doing that config on my LR quad. What I am wondering about is the third position where both angle and gps rescue are engaged. If sanity checks fail I think the quad will just do down and the angle will be bypassed. If the GPS rescue is toggled in the third position then the angle is again bypassed. So does enabling angle on the third position have any usefulness in any scenario? The second position angle mode is very useful. But is third position angle making any difference?
Hey I've tried to contact your email and through the site you use for the frame but haven't gotten a reply. Can I get the original files for the Fpv mount and the GPS mount. They are too small for what I need. Stl's are impossible to work with. Without it I can't use your frame
You should be able to get in touch through my email falconradfpv@gmial.com I only used an stl modeler for the 3d files. I could also give you an obj file if that's any better. Best to get in touch over email and I'll make sure to get something sorted out for you.
@@FalconRadFPV thank you very much, have no experience with Li-Ions... you say at 1:29 that you test it regularly, do you test it with the Failsafe AUX Switch or with the GPS Rescue Switch? Joshuar Bardwell made a video where he says you should test it always with the failsafe switch is that right or how would you do that? I have already lost one quad + GoPro on the Arcores Dez 2021...so i am Building GPS Builds 5&7 inch just for cinematic Long range dives...hopefully with GPS and your tutorial i can avoid it if next failsafe will acure.....thank you so much
@@FalconRadFPV when do you know, that the Li-Ion is empty, if it holds Voltage for so long? I want to get into it, but scared as fuck to loose a quad because of empty liion for example...it would be great to get a Battery Guide from you as a Video. Also for how you know, how far you can go up, till you have to dive down, to dont loose the quad because of empty battery with Li-Ion and Lipos....do you have a paypal to sent some money?
I've lost two quads that were never recovered. Not a bad record though, I must have done hundreds of long range flights now. Also I kinda push the limit sometimes so I'm expecting to lose one every now and again.
@@FalconRadFPV Sad to hear this. I recently lost 5" acro quad on analog. The shame is I didn't fly that far as it wasn't long range so it dropped somewhere near me up to 500 yards but in such a difficult wild nature terrain with high weeds and river - I didn't manage to find it again. I couldn't believe to what happened. It is devastating feeling. This and experiences like yours makes me want to fly micro just near me or local park and no further away anymore up to 100m. Quads are to small and to difficult to find. In my case I had GPS unit and buzzer all configured and tested many times yet it all has failed to help save and recover my quad. I hope you will never loose any again.
Current altitude is ABSOLUTELY NOT the best Mode to use! use should at least be using Max Alt! Please do your homework!
Hey Mark, it seems you have misunderstood the correct situation to use the different settings. To start, I am referring to my own personal settings that I find best for my typical long range flight situation. I assume you are thinking that if I lose connection at the top of the mountain and the drone goes to whatever the max altitude was that it should get high enough to recover signal. In such a scenario that would be correct. But now with the same settings a different scenario, I'm on my way back down the mountain everything is going fine, I'm most of the way back now and decide to go and check out a waterfall that I pass near. But now I fly behind a ridge between myself and the drone, if I activate GPS rescue in max alt mode it will continue to gain altitude until I get signal back and turn rescue mode off myself. Again you're right for this scenario it works.
But now lets stop thinking about only ourselves and dealing with an easily managed scenario. Drones are not 100% perfect they have bugs in firmware and the electronics are only consumer grade not aviation or military grade components. So say your goggle battery dies, or your FPV camera hits a branch and gets broken, or your crossfire antenna is damaged and you didn't notice. In all of these situations you will not be able to regain control of the drone and it will carry out the MAX ALTITUDE rescue mode. So I just flew up a 2.5km tall mountain and this happens close to home, so to start my drone will try to ascend 2.5km all at once, I fly with li-ion so it would never get up there it would kill the battery halfway up, die and drop. Say it has a half full lipo on board, ok so it doesn't drop it goes the whole 2.5km up but now its over top of me not the mountain so its literally 2.5km up in the air. That is absolutely not acceptable practice. This scenario would endanger full size aircraft and would be very irresponsible. Getting your drone back is not more important then making sure to stay out of the airspace of commercial aviation.
Current altitude will work for most situations. It can be set to go to a certain number of meters above current altitude, 50 or 100 meters would be a good setting if you're really worried about it not going high enough. With proper route planning done pre flight you should never need to use max alt rescue setting. Its purpose is for people that are NOT flying up mountains, like following a river for 2km out and you lose signal, then max alt would be safe in all situations. That's why it's an option because no one setting is CORRECT for every situation.
As well I am making a RUclips video that will be watched by thousands of people. It would be irresponsible for me to just tell everyone to use a potentially dangerous GPS rescue setting.
Commercial aviation safety MUST ALWAYS be the first thought in long range flights, nothing else is acceptable.
@@FalconRadFPV Boom...and that,s all she wrote! stick that in your pipe and smoke it mark crum..lol
@@FalconRadFPV haahahha the dude is still silent to this day :D
@@zeDoSauRus you can't necessarily know because youtube censors comments.
@@flat-earther lol yeah I'm sure he got censored 😂😂😂
I'm the only one among my FPV friends that has angle mode enabled for panic scenarios. I used to practice the muscle memory for hitting it regularly. It's saved me so many times, especially when getting stomped out by a nub plugging in without warning. Never understood why folks don't set it up.
On another note, might be a good idea to make a LR fundamentals series. Things like flight planning, preflight check, battery level management, failsafe plan(s), etc. At the very least introduce people to things to consider beforehand.
That's a great idea. I am planning on doing more long range flights with in flight narration as I'm flying (another camera on me and my spotter). I have a couple of videos already made that will be getting posted soon that touch on this concept. I've been thinking about a pre flight planning video, actually even tried recording a couple of them.
(I still have a video to do about losing a quad several months ago. I've been avoiding it because I feel a bit silly about how it happened. It was my first try at flying long range and talking to the camera at the same time. I got distracted by talking to the camera and my spotter got distracted by trying to think of helpful questions from a viewers perspective and we were both also distracted by what gopro shot to try getting next. In the end we both realized how low my battery was when it was too late! When I eventually get that video done it will have a few good lessons in it.)
to put it simply if it wasn't for this video I would have lost my quad three days ago because I did put it in angle mode and I did hit the throttle up and it did work because my goggles went dark but this gave me time to reconnect the goggles to the VTX I can never think this guy enough
surfing CPA Hawaii
Oh awesome! It's great to hear that it helped you out, that's one less lost quad!
Alot of ppl dont actually know about how you can use both angle and GPS mode to get out of a bad situation, so this tip is a good one!.. of course I like to see more of the actual flight characteristics in real world situations. If you got more flight footage of these things, that would be entertaining!... thank you for your content.
Thanks. That brings to mind a good video idea. I have a lot of footage where I go through temporary video loss. It often happens multiple times over a day of long range flights. I should do a compilation of short clips of losing video and how I handle it. It would be a good follow up video.
I’ll be waiting to see that! Sounds awesome!
Thank you so much for this! If there is anyone I would take GPS Rescue advice from it's you FalconRad! 😉
You're welcome!
After setting up betaflight I went back to re watch this gps video. Again very helpful. Thanks Conrad
Glad it helped!
I am almost sure that on Betaflight when the GPS Rescue is activated the Angle Model is selected automatically. After my first drone lost in long-range, I learned some things: (i) use powered beep; (ii) display and record the GPS coordinates on DVR goggles (never go flight without record is on); (iii) save automatically on the radio the flight log with GPS coordinates.
I started using angle on a switch when you recommended it awhile back. Very good advice I like to throw in angle and use yaw if needed to get signal back don't have to worry I'm upside down.
Thanks for the comment. Yes exactly, it gives that extra peace of mind when maneuvering blind for a couple of seconds.
You just need to make sure with gps / angle that when your quad calibration takes place your quad is actually flat and reasonably level.
Can we make a switch in OpenTx which when hit - it automatically turns on Angle mode, rises throttle level a little bit higher than hovering level and adds a little bit yaw rotation?
@@edgafpv its the same setting as you have for sure for arm switch. just add in mixes next switch, go to betaflight, try if you get signal from your radio and add angle mode in bf.
@@edgafpv it may be possible watch one of the bard well videos regarding throttle curve altered by switch… I would suggest you just stick to using the throttle manually
This is the best video on how to setup gps rescue! I did try out gps rescue on my new quad and followed the steps from your experience. Worked exactly as expected 👍
I've become very comfortable with fixed wing inav rth on failsafe since I live in the city and get fail-safes with csrf @1w well within the 5.8 video due to interference. I've found with quads I trust inav gps way more than betaflight but tuning is like betaflight was 4+ years ago, a headache. But I like that my home arrow points home and rth actually flys home Everytime.
Yes exactly, it's too bad we have to choose between good GPS function and good flight characteristics. But it's understandable, one firmware won't be great at everything. It's crazy how amazing the dev's get these things flying though.
@@FalconRadFPV ya, I always have to check myself before complaining about open source stuff if done nothing to contribute to. It's like complaining about trail conditions when you haven't lifted a finger to do any work.
What a relief as the video came back
yes it sure was, my heart was beating like crazy!
Set up my Falcon7 just like this and it works.
angle mode on gps rescue switch is gold jerry gold I tell you. Thanks man
Glad it helped you out.
This is an incredibly helpful and underrated video. Thank you so much for putting the time and effort into showing others, greatly appreciated. This video just got you a new patreon 👌🏻
You're very welcome!
Excellent, better explanation than many of the guys around! THANKS.
You're welcome!
Thanks for this video, I will definitely change my switching to a single switch for angle and then GPS rescue.
Glad it helped
Have set my 3 position switch the same way as you, works fine for me too 👍🏻
Nice 👍
Fantastic tips, dude! Thanks a lot! 😃
Stay safe there with your family! 🖖😊
Thanks very much! You to my friend. 👋👍
I was going to bother you yesterday for this video. Thank you so much fir posting it!
You're welcome. I really struggle with this type of video but I'm getting more comfortable with it as I do more of them.
@@FalconRadFPV this format was awesome. I usually fly angle anyway because I’m not very good. Thus video takes the mystery out of your recoveries. There weren’t as many differences to my settings as I would have thought, but you have made me more curious about reading the betaflight wiki and educating myself
Finally a great video that explains all very good not like others. I just soldered today GPS to my Protek35. I do it because i fly in mountains where is many cell towers and had 3 rxlosses and my quad crashed. Hope GPS Rescue help me in situation like that when i lose rc link conection. Thx for great video. Tomorrow must test how it works :D
I think it'll help, good luck with your testing!
@@FalconRadFPV Im really happy with results. GPS Rescue works very well. I switched off my radio, done 3 failsafes and more. This thing for sure will rescue my quad. But im not sure about angle settings in bf. I used 35 and it work good. But in high mountains sometimes wind is 30-40km/h so maybe raise angle to 40?
settings are ok but i would add that if you are flying over terrain that is deserted it would be preferable to turn off sanity checks they will drop your quad out of the sky for all sorts of silly reasons.
I would also turn off stage 1 failsafe or just reduce the delay to zero.
On defaults the radio will have its own guard time and then betaflight will have a time where it just holds does nothing or even worse drop throttle before initiating gps rescue. Ideally you want gps rescue turning on as soon as the receiver indicates failsafe.
I have had gps rescue save my drone from crashes when i got a short failsafes as i was diving at the ground.
The downside of not turning off sanity checks is that you might burn an esc if the drone crashes near you on rescue as it wont switch off the motors but its better than dropping out of the sky over a mountain because the gps module had a hiccup or you have a desync and it decides you collided with something and disarms the drone.
I wish they would add loiter mode to gps rescue as i do believe its much better a drone loiter until the battery is depleted than it crash with full power face blenders at its disposal.
Thanks for the comment. That's a good point you make about the delay of guard time. I think it shouldn't be 0 though. You don't want it kicking in all of a sudden because of a micro failsafe. Which are more common at longer ranges I think. I can't have sanity checks off where I live, well in the summer time at least, the chance of a fire is too great. I turn sanity checks off for everything except failsafes.
@@FalconRadFPV the radio system itself normally has a guard time but this is something you can test on the bench.
I would rather set current limit on esc's rather than sanity checks ever be enabled if your worried about starting fires.
Lots of good info! I'm gonna put angle mode and GPS rescue on the same 3 position switch ASAP.
Glad I could help!
It’s possible to set a switch position that triggers failsafe. This is a good way to test the behaviour when having a failsafe without actually having to turn off the tx or force a failsafe by flying behind something or miles away.
yes under the modes tab you can put failsafe on a switch to test it, after you're comfortable remove it and switch it back to gps rescue, turning off the TX is really unsafe so this mode was designed to simulate that without having to turn off the TX
Yes that's a good point! That would be a good way to test it.
Very useful! Thank you very much for the video!
I saw this right before my maiden flight this morning and I should have watched it. I have rescue set up on my other 7" and it has save me a few time so I want it working on my Falcon 7 as well. On my second short flight I decided to flip my rescue switch to test it out and the quad tumbled out of the sky, luckily I test at low altitude. Can't seem to figure out what the difference is between my 2 set ups where one works and the other doesn't. Now I watch this video and see how you have it set up.
If you you flipped the switch and it just dropped then my guess would be that it failed the sanity checks. If you continue to have trouble with it you could try looking at what the blackbox says. Maybe there's a gps rescue status debug mode? Read the betaflight wiki, gps rescue section. There is a part on the sanity checks and what they are. You may want to set your sanity checks to failsafe only, just be careful when you use it and know what the different sanity check settings do. It's explained well in the wiki. There's a link in the video description to the GPS rescue page of the wiki.
@@FalconRadFPV I was thinking that was well and I thought it was possible I was too close. I changed the setting to 50 meters and it still responded oddly. I have to really look at it.
@@FalconRadFPV I turned off sanity checks because of that
The remark about hitting disarm instead of rescue rings hard for me.
I'm interested in long range coming from Freestyle, where you keep a finger on your arming switch basically the whole time.
Could easily see myself reflexively disarming from a video loss...
Thanks for the vid.
why would you keep your finger on the disarm switch the whole time while freestyling? never disarm! :D
Very well made. Thanks for taking the time to explain this in such fine detail.
Thanks for the video! I build a lr 7 in based on your quad over a year ago and haven’t set it up yet.
wow, well I hope this was last thing you were waiting for to get it done!
I use GPS rescue this is a great tutorial
Thanks!
Excellent tutorial, I'm using it for my first long range flights!
I wonder if using Li-ion batteries it is necessary to decrease the rate of ascent and ground speed, because they are batteries with lower discharge rates than Li-Po ones (mine is a Li-ion GNB 4000mah 10C).
What do you think?
Man this is a GREAT video. Absolute nr.1 for GPS. I actually use the switches identically as you, just don't have angle+gps. What's the difference if there is only gps rescue? it goes into angle mode as-is.
Angle mode doesn't have to overlap gps rescue, but it's good to switch from rescue to angle mode then back to full control. It can help to avoid control issues as switching out of rescue mode.
@@FalconRadFPV yeah that makes sense :) thank you for the reply!
Go on my friend ....
I don't get it? But thanks anyways!
Very helpfull indeed, i know the most but i can always learn more. Im gonna use the same switch set up because it makes alot of sense
Thank you!
@@FalconRadFPV no thank you for sharing your knowledge so we can learn from you.
Very informative.. thanks for sharing your knowledge and experience
Glad it was helpful!
Love your videos! Keep up the great work. Just ordered ur frame from the CNC place and brother hobby motors from. Rotor Village... Can't wait to build a nice 7in long range. Be a great addition to my 6in long range.
Again, thanks so much for being so great about showing how u do what u do and how. 😁👍
Oh thanks so much! I really appreciate you saying that!
Hi there, I've got a Source One 7 inch with HGLRC M80 Pro GPS and Zeus F722 stack in it with 2807 1700kv Emax ECO motors. The quad flies great and I've even thought of putting a 6s battery on it with a 70% throttle limit. However... GPS rescue... thats the last hurdle I can't seem to figure out.
When I trigger gps rescue the quad will shoot up into the air and keep gaining altitude and in most cases also go off in a direction that is not "home". The home distance is always displayed correctly.
I've tried betaflight 4.2, 4.3 and even 4.4...
My throttle hover is set to 1250, my acend rate 3m/s and altitude mode is set to current altitude...
I've tried 2x different Zeuse stacks (one with the BMI270 and the other with the MPU6000) both do the same thing.
Before I put a 3rd flight controller in there (thinking of a Holybro F7 or a Mamba f405), I'm hoping you might have seen something like this before and could steer me into the right direction.
All my other 5 inch quads have gps units (5x quads) and their gps rescure works just fine...
I would suggest trying to swap out the GPS for a different brand, or it could be the GPS settings. Have you tried GPS rescue with leaving all the settings on default, or as many settings on default as possible, but try to do it with everything on defaults. In very rare cases even a GPS setting can cause a hidden/unknown conflict or firmware issue. If it works fine on all defaults, then change each setting one at a time and test, until one of them causes the issue you described. But if you've tried two different stacks, I'd suggest trying a different GPS next.
@@FalconRadFPV thx for the reply.. Different stacks but same hglrc F722. One with Bmi270 a d and one with mpu6000. Still can try my mamba f405 stack.
I've tried it all on defaults.
I've also gone and changed one at a time... Results of my other quads and in the video also this 7 inch where you can see the issue : ruclips.net/video/gGBFUM1Q6bM/видео.html
Maybe you have a magnetometer (compass) on the GPS module or in the FC. It's recommended to not use them unless you can keep it far away from any other wires and electronics (10 cm minimum, which is not possible on most quads). The compass might show into the wrong direction because of interference.
Also the orientation might be set up incorrectly in Betaflight. You should check the manual of your FC and GPS to set their orientation accordingly. A magnetometer has a separate orientation setting.
Also check that it's all installed with the arrow facing forward.
@@razorblade7108 thx for the reply. Swapping out the fc fixed all the issues. Seems the Zeus F722 stacks are just not that great.
Thanks for the great information!
Glad it was helpful!
In the failsafe procedure, you can choose drop or GPS rescue. In case of a broken receiver, the drone will drop or will fly back with GPS rescue. Since you cannot control the drone anymore with GPS rescue, I wouldn't want to be where there are buildings or people. My guess is that you better have your drone dropped, except when you are flying in the woods and mountains, like you are doing. Am I correct?
Yes that's right. When near buildings, vehicles or random people walking around then it's best to set it to drop. I always fly long range 20 or 30 km from the nearest buildings with very few people around.
Hi, i just tried gps rescue by switch for few times (BF v4.3.2), and i tried to fly my quad toward away from me (i face to east and i fly my quad to east too) and around 200m from Home Point, i turn on gps rescue switch, the quad suddenly turn 180deg and face to my position (which is good) and going up but why it flew far away from me? lol, so i turn off gps rescue switch and regain control. I set angle to 35, altitude mode= maximum, sanity check= failsafe only, initial altitude= 100m, minimum distance= 50 and others values are default value. thanks, subbed your RUclips channel.
great video series, I have the same three position switch setup
Thanks!
Hello merci beaucoup pour ce beau tuto 👏👏👏
Great video, thanks! I've just set up my Matek M8Q-5883 GPS, and all seems to be working except the home arrow; It doesn't point home, but the home distance is correct, I've tried uploading the font with the battery attached, and it still doesn't work. I was wondering if my tests need to be further from home to work. I've been flying 200m in a park on tests; the arrow is the wrong way or pointing to the side. I am nervous about flying far until I get this sorted. Thanks!
It's happened to me a few times, somehow it usually sorts it's self out if I fly over top of myself at the home point. That hasn't happened to me in months now though.
I almost have complete trust in inav rth. Betaflight not so much. But I generally fly quads in close proximity to myself and use fixed wings for lr.
Ya betaflight GPS fuction is very limited compared to INav. I keep thinking about getting an FPV plane setup....
Subscribed, thanks for the tips!
Good video. Doing a first time setup. Maybe I’ve missed it but what is the reasoning in turning off Mag?
Thanks! I don't have one installed. Mag also known as compass.
They are usually plagued with interference on quads. You might be able to place them somewhere on a fixed wing or very large quad where it has no interference from electrical components and wires, but usually it's better to use GPS for orientation. That requires flying away from the home point in a straight line for some distance (30-50 m should be fine) so Betaflight can get the direction right.
Very nice, I noticed you were using 4.2 back then. Are these settings still good for 4.4 version? Thanks.
The setup should still be quite similar although 4.4 has a few more options than 4.2 did. As always, and especially with GPS rescue, stick to changing things that you understand the effect of and do more than one test of the setup before relying on it to save you.
Great video, gives me more courage to do it. Thanks Cheers
Nice, just take it slow and don't go too far right away. A couple tips:
Get to know what mah count (OSD mAh used) you get with each battery.
Go 1 km out and back a bunch of times, to get an idea of total distance and flight times.
Then always turn around and come home when you are 40% of the way through the total mAh count you are expecting for that pack.
Great video! Wish this was up, before i had to learn all of these lessons the hard way XD Thanks for your effort & keep adding cool content!;-)
Thanks, will do!
Two thumbs up!
Always valuable advice.Thank's
My pleasure!
Excellent
You got a new sub!
great video and tips! thanks!!
Glad it was helpful!
Thank you 😊👍
You're welcome 😊
Regarding the 3 pos switch, why do you have angle mode in the 2nd _and_ 3rd position? Won't GPS Rescue take over on the 3rd position anyway? I.e. wouldn't it be enough to have angle mode only on 2nd position? What are the benefits of having angle mode and GPS rescue at the same time?
The though is that the FC is always in angle mode when changing between the two end positions. I've heard of instabilities when changing out of GPS rescue mode. It doesn't hurt having angle mode go all the way over. I believe that if it does not that the quad when gps rescue is turned off would leave angle mode (part of gps rescue) then switch back into angle mode again right afterwards.
It just seems reasonable to have it stay in that mode rather than exit and reenter it right away. In blackbox logs you can see that this process is actually quite rough unless you have the settings toned down in which case the gps rescue response is slowed and increases the risk of gps rescue crashing your quad.
Thanks for ur sharing.. It was great. I wanna ask u about failsafe setting. In menu failsafe switch choose stage 1 and stage 2 chose a gps. In failsafe switch why u use stage 1.
Stage one is a hold time between losing signal and activating gps rescue. This is so that if signal is lost for less than 1/2 a second it won't activate rescue mode unnecessarily.
@@FalconRadFPV so the gps it's ok right. Idont have to change the failsafe switch to stage 2. What is the difference when I choose the stage 2. Not stage 1.
Hi . I really like your videos. What do you think about betaflight vs INAV. You are not using the inav configurator. Why not ? Is Betaflig better? Obsession ?
I just like the way it tunes and flys with betaflight. I also don't feel the need for the automated stuff in INAV. That said, INAV has far superior GPS functions. The return to home works better, and it has stuff like hover in place and automated flight with way points and more. I just want to fly my quad up a mountain and keep it simple.
Thanks for the answer . Greetings from Hungary .
top content - you are my long range education! ;)
Thanks very much!
Very helpful content. Thanks!
You're welcome!
Great tips and video again. Totally agree with your recommendations.Thks for sharing. Off topic..was wondering if you have checked out sharkbyte vs analog. Very promising...I have been testing SB for LR.
Thanks. Interesting about sharkbyte. I was thought it may not have the necessary output power. I remember seeing a thumbnail for a sharkbyte video you did, I'll have to check it out!
@@FalconRadFPV the necessary power for LR is exactly what I've been testing. So far have been out 2 miles and I think one can push it further. A newer higher powered vtx is rumored to be in development.
nice video 😀 liked & subscribed, thanks for sharing 😀
Thanks and welcome
This might be a new feature, but what about "gps_rescue_alt_buffer"? My understanding is that this a the altitude added to "current altitude".
Great point to add! Yes the distance above current altitude is also a modifiable variable.
Great content, thanks for sharing! 👍
Thank you too!
Thanks for the video and tutorial. Am i correct the aux 3 switches between acro-angle-angle gps mode? When losing video signal do you switch the aux 3 to gps mode or does the fc go into failsafe gps mode. And when regaining video signal i would guess you make the switch out af gos mode and into pure angle mode. Thanks
I like to switch to angle mode and just throttle up to regain video rather than counting on GPS rescue. If that doesn't work I flick the switch alll the way to the end to engage GPS rescue.
If your drone failsafes it is best to switch into GPS Rescue mode until your video returns and then switch back to acro and retake control. This is because in odd cases of failsafe the drone could regain connection to the TX and return control to you even though video is still out so you want to make sure it stays in GPS rescue mode until you are fully ready to retake control.
When engaging angle mode, what do you think about pulling the pitch back a little while increasing the throttle? I realize this slows forward momentum while bringing the quad up faster.
If you are comfortable giving the stick inputs with no video then, yes! I actually do exactly that pull back on pitch and increase the throttle, I'll often do just that and skip activating GPS rescue.
one more thing, so thankfull, that you taking time to answer, is it true that if a failsafe happens, and GPS Rescue gets automatically on, i have also to switch my AUX GPS Rescue on, because the quad will fall if i dont have turned the switch on? Oscar Liang has explained it like that and that makes me a bit confused, why it should drop as soon as i have RC Signal back?? i share the exakt part in a comment below
Oscar Liang: "Activate Failsafe mode. Now the quad should enter GPS Rescue mode. You should also activate Rescue mode now, as I mentioned earlier. When you get out of Failsafe, you can manually disengage Rescue mode and that gives you enough time to take back control, otherwise it would just drop to the ground."
Sorry I don't understand the question. I find the 3 position switch setup that I cover in this video is the best way to do it.
I think he is talking about when you turn rescue mode off you have to move the sticks enough to let the FC know that you have taken back control. Just use the 3 position switch setup, it should prevent a fall out of the sky scenario.
Great video thank you!!!
I am still a beginner in the field of FPV, but I have already collected a few hours, simulator and outside. Now I wanted to ask how I can extend the frequency or the range of my drone? (Law of the drone does not matter ;) ) Feeling 30 meters I can fly and the image is already bad in my FPV glasses and can no longer control the drone practically. What exactly do I have to set in Betaflight so that I can fly further?
My equipment
Protek 35
DJI Goggles V2
DJI FPV Remote Controller V2
Greetings from Switzerland
Sorry I don't use the DJI FPV system. I use analog which is much different.
Question: did you set gps_use_3d_speed = ON or OFF? does it measure vertical and horizontal? is it really need? thank you
I left it set to off. I assume it tries to calculate vertical drop into the gps speed since gps speed.
Thanks great info
Hi FalconRad thanks for all your work. I’m using gps for the first time on my quad and set it up like you show in the video. Everything seems to work fine but sometimes mid flight e lose gps signal but after a few seconds i get it back. The number of sats seems to be stable before and after the signal loss. Do you know what might be the problem? Thanks
It could possibly be some sort of interference. Try moving the wires for the GPS away from other stuff like the VTX or receiver.
Nice flying sir, are you running dynamic mode on the crossfire module or locked at 50hz? Also what power output? I’m having some issues with dynamic and latency while jumping from mode 2. To mode 1
I just leave it on dynamic but I'm thinking about switching to locking it at 150 once I start doing more long range and less field testing in the spring. I use 500mW usually for power output.
@@FalconRadFPV thanks mate👍. If is just long range I’d definitely recommend locking it at 50hz, but more latency but heaps more penetration and range.
Thanks for sharing..it was in depth sharing as usual. Any spesific failsafe setting required in crossfire for this GPS rth to work flawlessl?
The crossfire receiver should have the failsafe setting set to "cut". This will halt all signals in the event of a failsafe so the FC will realize it's a failsafe situation.
@@FalconRadFPV thanks..👍👍👍
@@FalconRadFPV Finally complete my AOS falcon 7 build..it flew exceptionally well with the stock pid and filter setting..Have question with the GPS rescue. I noticed the quad drop in altitude after the GPS rescue initiation before its picking up the altitude in the next seconds. Is that a normal behaviour? Settings are as per your recommendation in the video.
Thanks for this Falcon! I've copied your settings but in betaflight modes settings I don't see the gps rescue turn yellow when I arm the switch. is that to be expected or am I missing a step somewhere?
Not sure, as long as you set it for aux XX and then you can see aux XX move in the transmitter tab when you flick the switch, then it should work as long it passes the sanity checks.
@@FalconRadFPV awesome thanks!
I am surprised you dont use iNAV.. I have BF on my 5" LR but my 7/8" LR has iNAV which not going to lie I do have 2 locations the compass gets thrown off though i didnt check the 5" there to see if it affects GPS at all
Also I set my speed to 35mph just cause in testing I think that was allowing the drone to cover the most distance per battery mah. Granted changes with motors and props being used.
Other thing I bring an extra battery to plug in and just fly around or idle waiting to get a lot of satellites. I usually wait for 10. I have a transmitter call out for over 10 satellites. one also for 5 if im impatient
I dont like my angle switch with GPS rescue just cause i use angle sometimes to just hover a secend doing something. and i dont want to accidentally hit gps rescue. but i do try to remember to hit angle when i lose video also before going to GPS rescue
Honestly I'm not keen on learning new firmware, so I just keep using betaflight instead of inav. Although I might have to get around to learning inav at least for the position hold and way points.
@FalconRadFPV position hold is nice. I didn't get way points working. Only tried once. Been meaning to try again. Also quad cruise mode
hihi hoho haha hihi hoho .. 1:40 when you accidentaly hit the disarm switch .. lol hohohahah hihi ... happened to me lol hoho. Darwin-price goes to me :)
So I put some soft-tape around that arm/disarm switch so I can feel, it's a special switch, and I make sure, I have no switch near there, what I would ever have to use on a flight. (especially the one just above the arm/disarm switch .. on that I have the vtx-on/off for now .. now until I figure out a better solution)
awesome content - thx!
Thanks for the comment!
Do you have an update to your settings with beta flight 4.5
I'm only just switching over to bf 4.5 now. I like to wait till all the bugs are worked out. I'm getting a couple of new quads tuned in bf 4.5 now.
can't see details of what you show on betaflight on my laptop. everything is so small. this video would need to be viewed on a large screen TV to see what you are doing.
Thanks, I'll keep that in mind for future videos.
i have two quads with GPS , a 5 inch with BF 4.2.0 and a 7 with 4.3.6
do you think this settings will work for both?
i really dont wanna change my firmwars.
thanks.
cool channel
sub
The main settings should work for both, although I do not have any experience with BF 4.3. I'm waiting for it to get the bugs fixed and the final release before I start using it. I have noticed that BF 4.1.7 has a much more responsive GPS rescue mode. I wish BF 4.2 GPS rescue worked as well, it starts off really slowly losing altitude before kicking in properly.
@@FalconRadFPV yes , i did some tests com my quds , 7inch 4.3.6 and 4.2.0 , th gps activates super fast , but it takes more time to start reacting comparad to your videos.
but it works.
@@FalconRadFPV but i think its okay for now . iam goint nowehre far like you.
ill be mostly at 1.5 mile away.
i was flying withou GPS on DJI Radio for the last year and a half. Now iam on crossfire and with GPS , gonna risk a little more.
thanks for sharing your experience
Regarding the issue of the top pIate covering the xt60. Is there a new design for the tpu?
There is no issue that I know of to do with the XT60. I've built this quad with the xt60 coming out the side, front and back. I'm using all the original TPU parts with no issues at all.
@@FalconRadFPV ok. The xt60 fits into the rectangular cut out on the tpu just below the falcon head . I assumed the xt60 fit there. I'll gladly secure the xt60 leads out the side. Thank you. Love the frame
One question again, in that video when u use a gps switch, how to u back to normal flying again.? By switching a angle mode or what
Moving the switch back to idle turns gps rescue mode back off and returns control to you.
@@FalconRadFPV thanks..
When the GPS Rescue is in control, it’s auto returns or manual?
It auto returns. The flight controller will do its best to try and fly the quad back towards you automatically.
Brother, I try to put the command, gps_rescue_yaw_p = 100 but the error window appears, what am I doing wrong?
Sorry about the late reply. Type set before the other stuff, so "set gps_rescue_yaw_p = 100"
hi , I have a question for you, how you make for configuration the altitude, yuo used barometer or gps or let default into the CLI, you can help me please thanks, this video is very interesting
The GPS will estimate the altitude, but if you have a barometer you can enable it in the configuration tab of betaflight. A barometer will help the flight controller to more accurately estimate the current altitude. No CLI needed for any altitude or barometer settings. Just the checkbox for barometer along with magnetometer and accelerometer in the config tab.
@@FalconRadFPVhi, Thanks, I'm going to set up my drone that way,👍👍👍
@@FalconRadFPV hi,Thanks, I'm going to set up my drone that way
Thank you, I was just trying to understand the GPS Rescue, and now I know! ¶ :-)
Happy to help!
Have you considered using inav?
Yes I have, It's a common question in the comments. I'm comfortable with betaflight so I just stick to using it. It's probably time that I get an INAV quad setup though. I'm sure I could find some interesting uses for the extra features.
master, by mistake I bought a gps without a compass, the matek SAM-M8Q, do you consider that the compass is very necessary?
No the compass isn't necessary. I just used the one with the compass because some people that use INav need it.
@@FalconRadFPV the gps without a compass will not show the arrow of my initial location? or the arrow is shown on all gps?
How do you set gps mag to off Wont accept gps_rescue_use_mag = Off when i put this in cli Cheers
use "set gps_rescue_use_mag = off"
How do you edit the settings inside the CLI? Thanks
It depends on what your doing. Sometimes it uses a SET command and sometimes it doesn't (like with resources I think). If you want you can email me at falconradfpv@gmail.com and I'll help you out with some screen grabs + instructions or something like that.
I'm assuming GPS Rescue just kicks into action all on its own, right? Or am I totally off base here? 'Cause if it does, why the heck is there a button for it?
I mean, what's the deal with that button if GPS Rescue is just doing its thing automatically, you know? It's like, "Hey, button, why you here if you ain't got no job to do?" :)
I'm kinda confused about that, man.
It does kick in automatically, but only if the connection to the transmitter (joystick) is lost. The video connection is a completely separate thing. If my video connection goes down (can't see where the drone is going) then I will use the switch to activate gps rescue so that I don't have to fly the drone with no video (blind).
Gotta confess, it never crossed my mind, probably 'cause I've been rocking the DJI FPV setup, and that feature's not in the cards.
Thanks for dropping that knowledge.
I know I'm hitting you up with questions, but I'm gearing up to explore the long-range scene. I'm itching to pick up some insights, and this one's been elusive - how's the VIDEO signal rollin' with DJI Goggles 2 and DJI O3 Air Unit?
Planning to soar with the iFlight Chimera Pro V2, RC Commando 8 (ELRS 918 MHz, 1W).@@FalconRadFPV
Hello i dont manage det get gps_rescue_yaw_p = 100. What command do you put in and what betaflight Version do you use?
Raising yaw P will make the quad turn around more quickly. It will do that with any betaflight version.
@@FalconRadFPV yes i know that , But what command do you write into cli to set it?
PLEASE JUST TAKE SHORT SEC: WHY the quad always drops at first till it rescues? if i get a failsafe close to gound (in dives or whatever in the mountains) my quad will still be lost even with GPS Rescue...i tested it, i always have to be like 20-30m off the ground, because if i am lower, the quad smashes the ground before gps rescue gets into it.... i will sent a paypal tip for you thanks so much
In the video I am using BF 4.1.7 GPS rescue is much faster and responsive in BF 4.1.7
I do fly BF 4.2 now but as you say the response in 4.2 is basically useless. I suggest practicing using the switch setup that I cover in the video so you can use auto level, throttle up, then engage rescue mode.
I have thought several times about going back to BF 4.1.7 because of how bad BF 4.2 rescue mode is.
@@FalconRadFPV thank you so much, my biggest Problem is, firstly, BF 4.3 flys untuned soo freaking good and i cant tune my quads sadly, i dont get it to the point of a really good flying quad mostly. secondly only in BF 4.3 i can see RSSI / LQ in DJI Goggles, thats sooo stupid....so i have to choose between a good flying quad and RSSI/LQ displaying or BF 4.1.7 for a good GPS Rescue....thank you so much for your information, what i dont get is, why they made GPS Rescue worse in a newer firmware, cant imagine, that this is a typical "bug"...is it official information your just your personal experience?
Hi, about gps rescue mag off, what it used for? Thanks
It's referring to a magnetometer, which is a compass for a quad. I don't use it so I turn it off.
@@FalconRadFPV ijust set my yaw to 100 in cli, yes i experience quad drift a little bit when hit rth, thats scary, and i see you explain how to manage the quad when hit the rth, immediately fast yaw and push very quickly thats important ^_^ thanks
good, when ı pull the rescue switch, if dont gps fix or something drone disarm, how ı can provide dont disarm keep acro mode
I'm not sure if I'm understanding your question. You can change it as a setting, under "sanity checks" in the failsafe tab. WARNING turning sanity checks off can start fires!!! I've heard of quads hitting the ground and going full throttle with no sanity checks.
I have sanity checks set to "failsafe only". So if I hit the switch to engage gps rescue mode it will bypass the sanity checks (risky know what you are doing!) but in the case of a failsafe it will still do sanity checks. READ THE BETAFLIGHT WIKI for gps rescue, read about the sanity checks.
@@FalconRadFPV no this is not atually, ı want when ı pull the resue swith, if drone is not resue capability drone keep going aro mode, not drop
that is for sure part of the sanity checks.
why failsafe switvh on stage 1? not use stage 2?
I'm pretty sure when you activate GPS rescue it skips right to stage 2.
@@FalconRadFPV yess, nope 0.40 second stage 1 to hover and angle mode
I don't understand the logic behind having a combo of Angle and GPS Rescue. Isn't GPS rescue an autonomous mode? Isn't GPS rescue a self level mode in a way?
Yes that's right. Although, if you are near the ground and have trees to your left with open space on the right, then lose video. Do you engage angle mode, roll right a little and throttle up for a couple of seconds until you are clear of tree tops and then switch to gps rescue? OR just switch to gps rescue right away and cross you fingers and hope that it stays away from the trees? If you are new to long range then straight to gps rescue may be the right choice. If you are an experienced pilot with the right setup and you have practiced this method in can increase the chances of getting your quad and GoPro back safely.
Also I've heard of people having control issues after switching out of gps rescue, it's always been fine for me, but going into angle mode on your way out of gps rescue should increase the chances of a smooth transition back to piloted flight.
@@FalconRadFPV I completely agree that the three position switch should have angle before the GPS rescue. It's a very logical step. And I'm doing that config on my LR quad.
What I am wondering about is the third position where both angle and gps rescue are engaged. If sanity checks fail I think the quad will just do down and the angle will be bypassed. If the GPS rescue is toggled in the third position then the angle is again bypassed. So does enabling angle on the third position have any usefulness in any scenario? The second position angle mode is very useful. But is third position angle making any difference?
Hey I've tried to contact your email and through the site you use for the frame but haven't gotten a reply. Can I get the original files for the Fpv mount and the GPS mount. They are too small for what I need. Stl's are impossible to work with. Without it I can't use your frame
You should be able to get in touch through my email falconradfpv@gmial.com
I only used an stl modeler for the 3d files. I could also give you an obj file if that's any better.
Best to get in touch over email and I'll make sure to get something sorted out for you.
12:30 how you got home over 3km with only 3,2V on that battery??🤯
Li-ion batteries run at slightly different voltage levels than a lipo does. It'll hang out at 3.3 to 3.2 for the whole trip home.
@@FalconRadFPV thank you very much, have no experience with Li-Ions... you say at 1:29 that you test it regularly, do you test it with the Failsafe AUX Switch or with the GPS Rescue Switch? Joshuar Bardwell made a video where he says you should test it always with the failsafe switch is that right or how would you do that? I have already lost one quad + GoPro on the Arcores Dez 2021...so i am Building GPS Builds 5&7 inch just for cinematic Long range dives...hopefully with GPS and your tutorial i can avoid it if next failsafe will acure.....thank you so much
@@FalconRadFPV when do you know, that the Li-Ion is empty, if it holds Voltage for so long? I want to get into it, but scared as fuck to loose a quad because of empty liion for example...it would be great to get a Battery Guide from you as a Video. Also for how you know, how far you can go up, till you have to dive down, to dont loose the quad because of empty battery with Li-Ion and Lipos....do you have a paypal to sent some money?
HI!!
Hey buddy! 👋
Did You ever recover You lost drones?
I've lost two quads that were never recovered. Not a bad record though, I must have done hundreds of long range flights now. Also I kinda push the limit sometimes so I'm expecting to lose one every now and again.
@@FalconRadFPV Sad to hear this. I recently lost 5" acro quad on analog. The shame is I didn't fly that far as it wasn't long range so it dropped somewhere near me up to 500 yards but in such a difficult wild nature terrain with high weeds and river - I didn't manage to find it again. I couldn't believe to what happened. It is devastating feeling. This and experiences like yours makes me want to fly micro just near me or local park and no further away anymore up to 100m. Quads are to small and to difficult to find. In my case I had GPS unit and buzzer all configured and tested many times yet it all has failed to help save and recover my quad. I hope you will never loose any again.
Do you adjust guard time and throttle low delay for Stage 2, or stick with default values? Thank you for sharing your settings.
I leave it on the defaults for those.
This guy walks on water if you ask me.
Over 60 Surfing CPA Hawaii